AD976BRRL - 16-Bit 100 kSPS SAR ADC | Analog Devices
MPN: AD976BRRL ✓ AktifAD976BRRL Ringkasan
An ADC is an analog-to-digital converter, a semiconductor that samples a continuously varying voltage and produces a corresponding digital code. The AD976 belongs to the successive-approximation ADC family, which compares the sampled input against a controlled reference and resolves each conversion bit in successive steps. Its switched-capacitor internal architecture supports accurate, repeatable conversion while allowing the device to operate from one 5 V supply.
Key features include 16-bit resolution, 100 kSPS throughput, one analog input, a parallel interface, and operation from a single 5 V source. The AD976 family is fabricated using Analog Devices' proprietary BiCMOS process, combining bipolar components with CMOS circuitry. The manufacturer also offers a related AD976A family with 200 kSPS throughput, while AD976BRRL remains the 100 kSPS member.
The parallel interface exposes the converted data directly across dedicated output pins, making the AD976BRRL suitable for systems where a microprocessor, digital signal processor, programmable logic device, or latch bank captures each conversion result. System timing must account for acquisition and conversion intervals, and the input driver must satisfy the converter's source-impedance requirements to allow the internal sampling network to settle accurately.
Typical uses include industrial process monitoring, instrumentation, laboratory data acquisition, communications equipment, embedded measurement systems, and control loops that require precise digitization without the throughput of a much faster converter. The 28-pin SOIC package also supports compact analog and digital routing on conventional through-hole assembly boards.
For reliable operation, use a clean 5 V supply and place the required bypass capacitors close to the device. Preserve the manufacturer's recommended analog and digital grounding arrangement, provide a low-impedance input source, and route the parallel output bus away from sensitive analog input traces. These measures reduce supply disturbance and switching-related conversion error.
This product page organizes the AD976BRRL's conversion rate, resolution, interface, package, ordering information, and practical selection considerations. It also distinguishes the 100 kSPS AD976 from the faster 200 kSPS AD976A and identifies the verified drop-in alternatives that can be used without changing the 28-pin SOIC footprint.
Pilihan pengganti yang segera untuk AD976BRRL — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
AD976BRZRL
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
AD976BRRL Penilaian maksimum & Ciri-ciri Elektrik
| Converter Type | Successive-approximation ADC |
| Pemecahkatan | 16 bit |
| kadar sampling | 100 kSPS |
| Analog Input Count | 1 input |
| Architecture | Switched-capacitor ADC |
| Process Technology | Proprietary BiCMOS |
| Tegangan Pemberi Arus | 5 V single supply |
| Data Interface | Parallel |
| Output Data Width | 16 bit |
| Kemasan | 28-SOIC, 0.295 in (7.50 mm) body width |
| Terminal Count | 28 terminals |
| Jenis Pemasangan | Surface mount |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Packaging | Tape and reel |
| Temperature Grade | Industrial |
| Maximum Power Dissipation | 100 mW |
| Internal Reference | Selectable internal or external reference |
Panduan Konfigurasi Pin AD976BRRL rectangular
Konfigurasi pin untuk AD976BRRL (rectangular pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk AD976BRRL.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
AD976BRRL patut untuk 6 aplikasis: Industrial Process Monitoring, Laboratory Data Acquisition, Industrial Control Systems, Communications Signal Conditioning, Embedded Measurement Systems, Audio and Vibration Measurement.
Industrial Process Monitoring
The AD976BRRL fits process-monitoring systems that digitize pressure, temperature, flow, or position signals at up to 100 kSPS. Its 16-bit resolution preserves fine amplitude detail, while the parallel interface allows a controller or logic device to capture each conversion without requiring a high-speed serial link. The single 5 V supply simplifies integration with industrial control electronics. The main design consideration is source impedance: the analog input driver should settle the converter’s switched-capacitor sampling network within the acquisition interval specified by Analog Devices. A clean 5 V rail and short analog traces are also important for avoiding conversion error in systems containing switching power converters.
Disebarkan
Laboratory Data Acquisition
The AD976BRRL is suitable for laboratory instruments that sample quasi-static or moderately dynamic analog waveforms at 100 kSPS. A 16-bit code width supports detailed amplitude measurement, and the parallel output can feed a buffer, FPGA, or embedded controller with predictable acquisition timing. The 28-pin SOIC package also makes the converter practical for modular laboratory equipment built on conventional assembled circuit boards. Designers should preserve the manufacturer's recommended decoupling and grounding arrangement and verify that the source impedance, bandwidth, and input range satisfy the AD976 acquisition requirements. A 5 V reference or external reference arrangement must also follow the device’s specified configuration.
Disebarkan
Industrial Control Systems
The AD976BRRL can serve as the analog front-end converter in closed-loop industrial control equipment that operates below the device’s 100 kSPS throughput limit. Its 16-bit resolution supports accurate feedback measurement, and the parallel bus simplifies direct connection to digital control logic. Single 5 V operation helps align the converter with common embedded control rails. For motor, actuator, or power-converter systems, the analog input must be conditioned to prevent out-of-range transients, and digital output activity should be routed away from the analog node. The acquisition path should include enough settling time for the converter’s switched-capacitor input and should be validated across the intended signal bandwidth.
Disebarkan
Communications Signal Conditioning
The AD976BRRL is applicable to communications equipment that digitizes received or monitored analog channels at moderate rates. Its 16-bit resolution is useful when preserving signal amplitude information, while the 100 kSPS sampling capability and parallel interface support straightforward integration into channel-processing logic. The converter’s single 5 V supply can simplify board-level power planning, although system designers must isolate sensitive RF or baseband paths from digital switching noise. Proper bypass placement, a controlled reference configuration, and a low-noise analog input driver are necessary to maintain conversion quality. The selected sampling rate should also satisfy the applicable bandwidth and aliasing requirements rather than relying only on the converter’s nominal throughput.
Disebarkan
Embedded Measurement Systems
The AD976BRRL is well suited to embedded measurement systems that convert one analog channel into a 16-bit parallel result for a microprocessor or digital signal controller. Its 100 kSPS maximum sampling rate supports many sensor and feedback signals while avoiding the routing and timing complexity of a high-speed serial ADC. The 28-pin SOIC package is convenient for leaded assembly and repair. To achieve consistent results, the input buffer must provide low noise and adequate settling, while the digital bus should be properly terminated according to the system architecture. Supply decoupling and analog grounding should follow the manufacturer layout guidance so that switching activity does not consume the converter’s available precision.
Disebarkan
Audio and Vibration Measurement
The AD976BRRL can be used for audio or vibration acquisition paths whose useful bandwidth can be represented within a 100 kSPS sampling rate. The 16-bit resolution provides a substantial dynamic range for amplitude analysis, and the parallel interface allows each sample to be transferred into a digital processing chain. Input scaling must keep the signal within the converter’s permitted range, while anti-alias filtering must be selected for the actual sampling rate rather than the nominal conversion throughput alone. Low-noise analog routing, controlled grounding, and careful separation from digital clock and return currents are essential. The single 5 V operating requirement simplifies common test and measurement rails but does not remove the need for local supply bypassing.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk AD976BRRL — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | AD976BRZRL |
|---|---|---|
| Package | 28-SOIC | 28-SOIC - same |
| Brand | Analog Devices | Analog Devices |
| Resolution | 16 bit | 16 bit |
| Sampling Rate | 100 kSPS | 100 kSPS |
| Converter Architecture | Successive-approximation, switched-capacitor | Successive-approximation, switched-capacitor |
| Supply Voltage | 5 V single supply | 5 V single supply |
| Data Interface | Parallel | Parallel |
| Process Technology | Proprietary BiCMOS | Proprietary BiCMOS |
| Analog Input Count | 1 input | 1 input |
Penyeberangsung Jelas
- 16-bit resolution at a 100 kSPS sampling rate (vsAD976A)
- Parallel digital output simplifies direct system capture (vsAD976A)
- Single 5 V operation reduces supply complexity (vsAD976BRZRL)
Catatan Desain
Place the required 5 V bypass capacitors immediately adjacent to the supply and ground pins, and route them through the shortest practical path. Keep the analog input and reference traces away from the 16-bit parallel output bus, especially clock and control lines. Use the analog and digital grounding arrangement specified in the manufacturer datasheet; separating noisy return currents prevents switching activity from appearing as errors on the converted code.
Design the analog source network so that it settles completely during the converter’s acquisition interval. The switched-capacitor input can draw transient charge during sampling, so a source impedance that is too high may cause incomplete settling and correlated conversion error. Use a low-noise buffer when the sensor or divider cannot present the required impedance, and include an anti-alias filter whose cutoff is appropriate for the 100 kSPS sampling rate.
Do not substitute the AD976A for the AD976BRRL without redesigning the acquisition timing. The AD976A is specified for 200 kSPS, while AD976BRRL is specified for 100 kSPS; the twofold throughput change alters signal-bandwidth, acquisition, and downstream timing assumptions. Also verify the complete ordering suffix, temperature grade, package drawing, and reference configuration before using AD976BRZRL as a replacement.
Maklumat Kesediaan
The AD976 product page and listed distributor information do not explicitly establish the requested environmental or material-compliance declarations. AEC-Q100 is not applicable because the AD976BRRL is an industrial ADC rather than an automotive-qualified device.