ADM232AARNZ - 200kbps RS-232 Transceiver | Analog Devices
MPN: ADM232AARNZ ✓ AktifADM232AARNZ Ringkasan
An RS-232 transceiver is a semiconductor interface that combines digital line drivers and receivers with level-shifting circuitry for unbalanced serial communication. The broader hierarchy is transceiver → serial interface IC → interface IC → semiconductor. It converts logic-level signals from a host, microcontroller, or data-processing system into bipolar RS-232 signals, while receiving and translating remote RS-232 signals back into logic-compatible levels. This makes the ADM232A family appropriate for point-to-point serial links where longer reach and noise immunity are more important than the low cost of a 3.3 V RS-232 interface.
Key features include two transmit channels, two receive channels, a maximum data rate of 200 kB/s, operation from one 5 V supply, and 0.1 µF charge-pump capacitors. The approximately ±9 V transmit swing and ±30 V receiver input capability provide compatibility with standard RS-232 equipment. The device is designed for higher signaling speeds than the lower-speed ADM232L family, making it useful where command, configuration, or control traffic must move reliably across an RS-232 connection.
Internally, the charge pump converts the single 5 V supply into the positive and negative voltages required by RS-232 drivers. The receiver side detects the bipolar input levels and produces a logic-level output for the host. The Analog Devices ADM232A product page identifies the ADM232A as a pin-compatible, high-speed upgrade for the AD232 and ADM232L. It is offered in 16-lead DIP and narrow or wide surface-mount SOIC packages, giving designers multiple package options when balancing footprint, assembly cost, and thermal considerations.
Typical uses include industrial control consoles, laboratory instrumentation, barcode scanners, service equipment, point-of-sale systems, and embedded systems that retain an RS-232 communication port. The two-driver, two-receiver arrangement suits full-duplex point-to-point links carrying data in both directions. In cable-based systems, the RS-232 electrical standard is intended for short-distance, unbalanced, point-to-point communication, so the ADM232AARNZ should be paired with suitable connectors and cable routing.
PCB implementation requires close placement of the 0.1 µF charge-pump capacitors and careful treatment of the RS-232 pins as high-voltage signal nodes. Keep unprotected connector-side traces away from low-voltage logic, preserve adequate spacing, and provide a stable ground reference. Confirm the complete pin assignment, including any no-connect or enable-related pins, against the manufacturer datasheet before assigning tracks or producing a footprint.
This page combines manufacturer specifications, package information, sourcing guidance, cross-reference candidates, and application-specific design considerations. It also identifies where package, pinout, or qualification details must be confirmed in the datasheet before a component is approved for production.
Pilihan pengganti yang segera untuk ADM232AARNZ — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera ADM232AARNZ (sama faktor bentuk dan kaki) — berbeza dalam Package, Charge-Pump Capacitor Value, Product Type, Number of Drivers, Number of Receivers.
ADM231LAR
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →ADM234LAR
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →ADM237LARZ
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ADM232AARNZ Spesifikasi
| Product Type | 2/2 RS-232 transceiver |
| Driver Channels | 2 |
| Receiver Channels | 2 |
| Maximum Transmission Rate | 200 kB/s |
| Tegangan Pemberi Arus | 5 V |
| Charge-Pump Capacitor Value | 0.1 µF |
| Driver Output Swing | ±9 V |
| Receiver Input Levels | ±30 V |
| RS-232 Compliance | EIA-232-E and V.28 |
| Logic Type | CMOS RS-232 driver/receiver |
| Kemasan | 16-lead narrow SOIC |
| Kiraan Pin | 16 pins |
| Jenis Pemasangan | Surface mount |
| On-Board DC-DC Converter | Yes |
Panduan Konfigurasi Pin ADM232AARNZ 16-lead narrow soic
Konfigurasi pin untuk ADM232AARNZ (16-lead narrow soic pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk ADM232AARNZ.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
ADM232AARNZ patut untuk 6 aplikasis: Industrial Control Console, Laboratory Test Instrument, Point-of-Sale Terminal, Embedded Serial Service Port, Barcode and Data Collection Equipment, Instrumentation and Control Backplane.
Industrial Control Console
The ADM232AARNZ fits a legacy industrial console that must retain an RS-232 service port while moving commands and status data in both directions. Its two drivers and two receivers support a full-duplex point-to-point arrangement, while the 200 kB/s rate is appropriate for short control frames and configuration sequences. The single 5 V supply simplifies system power design, and the on-chip charge pump avoids a discrete negative supply. Place the 0.1 µF charge-pump capacitors close to the device and keep the RS-232 traces away from sensitive logic. Because the console may expose an external connector, maintain suitable spacing from unprotected low-voltage circuitry and provide a reliable ground connection.
Disebarkan
Laboratory Test Instrument
The ADM232AARNZ is suitable for a laboratory instrument that accepts setup commands and returns measurements through a wired RS-232 link. The 200 kB/s transmission rate supports short measurement records and command responses without requiring a high-speed differential bus. Two transmit and two receive channels allow bidirectional communication with a host computer, while the approximately ±9 V driver swing and ±30 V receiver capability support conventional RS-232 signaling. Use the receiver input rating to define connector protection requirements, and keep the long external cable interface isolated from sensitive analog measurement circuitry. The single 5 V operating supply also simplifies portable test equipment power trees.
Disebarkan
Point-of-Sale Terminal
The ADM232AARNZ can serve a point-of-sale terminal or peripheral that uses an RS-232 receipt printer, scanner, or customer-display interface. Its 2/2 channel arrangement supports simultaneous command transmission and response reception, while 200 kB/s is more than adequate for short transaction and status packets. Operating from one 5 V rail reduces the number of external power rails in compact equipment, and the charge-pump capacitors require only 0.1 µF each. Route connector-side RS-232 nets away from display and switching-power sections, observe the receiver's ±30 V input range, and verify the cable shield and ground strategy to reduce common-mode interference in retail installations.
Disebarkan
Embedded Serial Service Port
The ADM232AARNZ fits an embedded controller or data-acquisition module that retains a wired service and configuration port. The two receivers can monitor command and status lines, while the two drivers support outbound responses on a full-duplex connection. Its 200 kB/s maximum rate allows firmware to exchange setup files or diagnostic packets through RS-232, and the internal charge pump eliminates the need for a separate negative power rail. Treat the external interface as a potential surge and ESD entry point, place protection appropriately without degrading receiver operation, and keep transceiver switching and connector traces separated from precision analog and high-impedance measurement nodes.
Disebarkan
Barcode and Data Collection Equipment
The ADM232AARNZ is appropriate for barcode scanners and local data-collection devices that communicate with a host over RS-232. The 2/2 transceiver arrangement supports inbound scan data and outbound configuration or acknowledgment messages, while 200 kB/s provides ample margin for short packets. A single 5 V supply suits battery-operated and handheld equipment, and the charge-pump implementation reduces required external capacitance. Keep the transceiver and protection network close to the connector, use a low-impedance ground plane, and route the interface away from radios, motor controls, and switching supplies that could inject noise onto the external cable.
Disebarkan
Instrumentation and Control Backplane
The ADM232AARNZ can be used as a point-to-point interface between a controller and remotely located instrumentation over RS-232. The 200 kB/s rate supports control commands, status polling, and compact telemetry blocks, while the ±30 V receiver range accommodates standard bipolar RS-232 levels. Its single-supply architecture reduces power-distribution complexity in multi-card systems, but the designer must still account for the voltage difference between logic-side ground and connector-side ground. Establish a deliberate common reference, consider isolation when ground potentials may vary, and follow the manufacturer's pin and capacitor placement guidance to preserve reliable data transmission.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk ADM232AARNZ — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | ADM231LAR | ADM234LAR | ADM237LARZ |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-lead narrow SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Transceiver Configuration | 2/2 RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver |
| On-Chip Charge Pump | Yes | Yes | Yes | Yes |
Penyeberangsung Jelas
- Documented high-speed capability (vsADM231LAR)
- Established RS-232 electrical alignment (vsADM234LAR)
- Small charge-pump capacitor requirement (vsADM237LARZ)
- Full-duplex channel count (vsADM231LAR)
Catatan Desain
Place the two 0.1 µF charge-pump capacitors as close as practical to the ADM232AARNZ charge-pump pins, using short traces and a continuous ground reference. Confirm the exact capacitor polarity and connection from the manufacturer datasheet before layout release. Keep the associated switching-node copper compact and away from receiver inputs, clocks, and analog measurement signals to minimize capacitive coupling.
Treat the connector-side RS-232 nets as bipolar signal nodes that can operate to ±30 V. Maintain adequate clearance from low-voltage logic and exposed conductive features, and do not rely on the IC package alone for user-accessible isolation. If an exposed DB-9 or equivalent connector is used, assess connector insulation, surge protection, and the return-current path as part of the complete interface design.
Do not substitute a candidate solely because it is described as a functional replacement. Before approving ADM231LAR, ADM234LAR, or ADM237LARZ, compare every pin name, logic threshold, propagation delay, driver slew rate, receiver threshold, supply limit, and charge-pump capacitor value against the ADM232AARNZ datasheet. Also verify the exact 16-pin narrow-SOIC outline and land pattern rather than assuming that every 16-pin SOIC is dimensionally interchangeable.
Route the external RS-232 cable interface away from switching regulators, high-speed clocks, and sensitive analog inputs. Provide a low-impedance common ground between the transceiver and its communicating equipment, and use a shield termination strategy appropriate for the installation. These practices reduce common-mode conversion and cable-coupled noise, which can otherwise cause intermittent receive errors even when the data rate is well below the 200 kB/s maximum.
Maklumat Kesediaan
The available product information does not explicitly state the requested compliance attributes. No environmental or automotive qualification is assumed.