ATTINY44-20PU - 20MHz 8-Bit AVR MCU | Microchip Technology
MPN: ATTINY44-20PU ✓ AktifATTINY44-20PU Ringkasan
An 8-bit microcontroller is a compact programmable controller built around a CPU, nonvolatile program memory, data memory, and peripheral interfaces. The ATTINY44 belongs to the ATtiny family, which sits within the AVR product family and broader embedded-controller hierarchy. Its single-clock-cycle instruction execution and 256-byte working register file make it suitable for responsive control tasks that do not require the memory or processing power of a 32-bit MCU.
Key device attributes include 4 KB Flash organized as 2K by 16 bits, 256 bytes of EEPROM, 12 I/O pins, and operation up to 20 MHz. The in-system programmable architecture allows firmware to be programmed or updated while the device is mounted in its application circuit. Peripheral resources support embedded sensing, timing, serial communication, and general-purpose control, although detailed converter and timer limits must be checked in the manufacturer datasheet before a specific design is released.
The AVR enhanced RISC architecture uses a compact instruction set designed for efficient embedded execution. Program storage remains nonvolatile, while SRAM supports working variables and stack operations. The device combines a RISC-like processing core with dedicated peripherals, allowing software and hardware timers to control motors, lamps, sensors, and communications interfaces without requiring a separate host processor.
Typical uses include compact industrial controls, hobby robotics, sensor nodes, LED sequencers, simple UART-connected instruments, and small standalone control boards. The 14-pin PDIP package also makes ATTINY44-20PU convenient for prototypes, educational kits, and through-hole assemblies where reworkability and socketed programming can be valuable. Its modest memory footprint suits finite-state control and monitoring tasks rather than demanding connectivity stacks or graphical workloads.
When designing the board, preserve the package pin assignments and route decoupling close to the supply pins. Confirm oscillator, programming, reset, and unused-pin requirements from the manufacturer datasheet. Use the in-system programming interface for firmware updates and validate timing margins before adding UART or timer-dependent functions. Check the selected fuse and clock configuration against the intended operating conditions.
This page combines the device specifications with application guidance, package-level information, verified pricing references, and practical replacement considerations. It is intended to accelerate component selection while keeping the final schematic, firmware, and production decisions grounded in the manufacturer documentation.
Pilihan pengganti yang segera untuk ATTINY44-20PU — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera ATTINY44-20PU (sama faktor bentuk dan kaki) — berbeza dalam Flash Memory, General-Purpose Working Registers, Product Type.
ATTINY44A-PU
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →ATTINY44-20PU Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | 8-bit AVR microcontroller |
| Frekuensi Klock Maksimum | 20 MHz |
| Flash Memory | 4 KB (2K x 16 bits) |
| EEPROM Memory | 256 bytes |
| Number of I/O Pins | 12 pins |
| CPU Architecture | AVR enhanced RISC |
| Instruction Word Size | 16 bits |
| General-Purpose Working Registers | 8 registers |
| Program Memory Type | In-system programmable Flash |
| Kemasan | 14-pin PDIP |
| Jenis Pemasangan | Through-hole |
| UART | Available |
| SPI | Available |
Konfigurasi Pin ATTINY44-20PU
| Pin 1 | VCC — Supply voltage input |
| Pin 2 | PC0/A7 — Port C input/output pin with ADC alternate function |
| Pin 3 | PC1/A8 — Port C input/output pin with ADC alternate function |
| Pin 4 | PC2/A9 — Port C input/output pin with ADC alternate function |
| Pin 5 | PC3/A10 — Port C input/output pin with ADC alternate function |
| Pin 6 | GND — Ground connection |
| Pin 7 | PB3/A11 — Port B input/output pin with alternate peripheral function |
| Pin 8 | PB2/A12 — Port B input/output pin with alternate peripheral function |
| Pin 9 | PB1/A13 — Port B input/output pin with alternate peripheral function |
| Pin 10 | PB0/A14 — Port B input/output pin with alternate peripheral function |
| Pin 11 | PA3/A15 — Port A input/output pin with ADC alternate function |
| Pin 12 | PA2/A16 — Port A input/output pin with ADC alternate function |
| Pin 13 | PA1/A17 — Port A input/output pin with ADC alternate function |
| Pin 14 | PA0/A18 — Port A input/output pin with ADC alternate function |
Aplikasi Biasa
ATTINY44-20PU patut untuk 6 aplikasis: Compact Industrial Control Module, UART Sensor and Diagnostic Console, LED Sequencer and Display Controller, Small Robotics and Motor Controller, Battery-Powered Sensor Node, Educational Robotics and Maker Controller.
Compact Industrial Control Module
The ATTINY44-20PU fits compact control modules that monitor inputs and operate relays, indicators, or actuators. Its 20 MHz clock provides useful timing margin for debouncing, state-machine execution, and periodic scheduling, while 12 I/O pins are sufficient for several inputs and outputs on a small board. The 4 KB Flash limit is the principal design constraint, so firmware should be compact and avoid unnecessary library overhead. Firmware can use the in-system programming interface to support production programming and later field updates without removing the device from its socketed or through-hole assembly.
Disebarkan
UART Sensor and Diagnostic Console
The ATTINY44-20PU is appropriate for a UART-connected sensor or diagnostic console that converts readings into a compact command protocol. Its 20 MHz operating speed leaves room for interrupt-driven serial handling and application logic, while the 12 I/O pins can support an analog sensor, status LEDs, and a control output. The device's 256-byte EEPROM can retain configuration values when the application needs limited nonvolatile settings. Firmware size must remain below the 4 KB Flash capacity, and the serial baud rate, frame format, and pin assignments should be validated against the chosen UART implementation.
Disebarkan
LED Sequencer and Display Controller
The ATTINY44-20PU can drive LED sequences, status indicators, or simple display-control boards because its 12 I/O pins provide enough parallel outputs for several discrete functions. The 20 MHz clock supports precise timing updates and multiplexed patterns, while 4 KB of Flash is adequate for compact lookup tables and sequencing logic. A designer should account for current limits, driver transistors, and resistor sizing rather than driving loads directly from an I/O pin. In-system programming makes it convenient to update lighting patterns during assembly without redesigning the board.
Disebarkan
Small Robotics and Motor Controller
The ATTINY44-20PU is useful as the supervisory controller in a small robot or hobby mechanism where it coordinates inputs, indicators, and low-power actuator commands. Its 20 MHz clock is suitable for responsive event handling and timer-based control, while the 14-pin PDIP package simplifies prototyping and repair. The available 4 KB Flash and 12 I/O pins require careful resource budgeting, especially if the design also runs motor algorithms or stores motion tables. Motor transients, grounding, and supply separation must be handled outside the MCU to prevent noise or overvoltage from affecting the controller.
Disebarkan
Battery-Powered Sensor Node
The ATTINY44-20PU can serve as the logic core of a battery-powered sensor node when measurements, filtering, and communication can be handled in a small amount of code. Its 12 I/O pins allow connection of sensors and wake-capable peripherals, and the in-system programming interface simplifies development and maintenance. Low-power behavior depends on the selected operating mode, peripheral configuration, and external sensor load, so quiescent-current and wake-time values should be checked in the manufacturer datasheet. For duty-cycled operation, firmware should disable unused peripherals between measurements to reduce battery drain.
Disebarkan
Educational Robotics and Maker Controller
The ATTINY44-20PU is well suited to educational robotics and maker projects because it combines an approachable AVR architecture, a 20 MHz clock, and a straightforward 14-pin through-hole package. Students can program it in-circuit, use timer and serial functions in classroom exercises, and construct temporary sensors or motion-control demonstrations without a complex fine-pitch footprint. The 4 KB Flash and 256-byte EEPROM encourage disciplined code organization and provide enough persistent storage for simple settings. The same characteristics make it useful for open-source controller boards, provided the selected toolchain and board definition support the exact device variant.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk ATTINY44-20PU — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | ATTINY44A-PU |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 14-PDIP | 14-PDIP |
| Product Type | 8-bit AVR microcontroller | 8-bit AVR microcontroller |
| CPU Architecture | AVR enhanced RISC | AVR enhanced RISC |
| Mounting Type | Through-hole | Through-hole |
Penyeberangsung Jelas
- 20 MHz operating grade in a compact 14-pin PDIP (vsATTINY44A-PU)
- Compact 4 KB Flash configuration (vsATTINY44A-PU)
- In-system programmability (vsATTINY44A-PU)
Catatan Desain
Place the device programming connector, reset path, and decoupling according to the manufacturer reference configuration. The 14-pin PDIP footprint simplifies through-hole routing, but analog inputs and serial signals should remain away from noisy switching nodes. Preserve access to the programming interface after assembly so firmware can be updated in production and service without cutting traces.
Budget the 4 KB Flash limit before adding application features or large framework code. The 20 MHz clock provides timing margin, but power consumption still depends on clock selection, active mode, sleeping behavior, and enabled peripherals. Disable unused timers, communication interfaces, and analog blocks where practical, and confirm the operating-voltage range from the manufacturer datasheet before designing the supply network.
Do not treat an ATtiny84 board as automatically compatible with the ATTINY44-20PU. Although both devices are AVR-based and may expose familiar peripherals, Flash size, SRAM, I/O count, pin multiplexing, and package details can differ. Verify the exact schematic, footprint, fuse settings, and firmware memory map before using a smaller device as a replacement.
Use the manufacturer pin table as the authoritative mapping for all 14 pins, especially ADC-capable I/O pins. Keep sensitive analog inputs short, provide a stable reference arrangement when using the converter, and route high-current loads away from the MCU supply pins. Because the PDIP pins are exposed, add appropriate protection against conductive contamination and mechanical damage in uncontrolled environments.
Maklumat Kesediaan
The current product listings do not explicitly state the requested compliance attributes. AEC-Q100 is not applicable because the device is a general-purpose microcontroller rather than an automotive-qualified component.