ATTINY84-20MU 20MHz 8KB AVR MCU | Microchip Technology
MPN: ATTINY84-20MU ✓ AktifATTINY84-20MU Ringkasan
An 8-bit microcontroller is a microprocessor integrated with memory, peripherals, and I/O in one semiconductor package. The ATtiny84 belongs to the TinyAVR family, which combines the AVR enhanced RISC architecture with low-power operation and a compact pin count. Within the hierarchy of embedded semiconductors, ATtiny84 devices are microcontrollers, controllers, and programmable logic devices commonly used for local sensing, actuation, signal conversion, and system supervision.
Key features include an 8-bit AVR core operating at up to 20 MHz, 8 KB of built-in flash, 512 bytes of EEPROM, 512 bytes of SRAM, 12 general-purpose I/O pins, and an 8-channel 10-bit ADC. Two 8-bit and 16-bit timer/counter sections provide timing and PWM functions, while internal and external interrupt sources support responsive event-driven control. The operating range of 2.7 V to 5.5 V allows use in both 3.3 V and 5 V systems.
The TinyAVR architecture is based on a RISC processor core using 32 general-purpose working registers. The ATTINY84-20MU combines this register-based execution model with on-chip nonvolatile storage and analog conversion, reducing external component count. Its 20-QFN-EP construction supports compact boards, while the exposed-pad package option requires attention to PCB copper and soldering during assembly.
Typical applications include compact sensor nodes, industrial condition-monitoring modules, low-power instrument controls, LED lighting controllers, battery-operated accessories, and small automation products. The 12 I/O lines can connect switches, sensors, indicators, and actuators, while the ADC supports direct measurement of analog inputs. The 8 KB flash capacity is suitable for moderate control logic rather than connectivity-heavy firmware.
PCB design should preserve clean routing around the exposed pad and provide the decoupling and programming access required by the device package. Confirm ADC input ranges, timer outputs, reset behavior, and programming connections against the manufacturer pin description table before layout release. The -40°C to +85°C specification supports industrial-temperature environments, but the finished assembly must also remain within its own thermal limits.
This page combines the ATtiny84 manufacturer specifications, package information, lifecycle status, practical design guidance, and comparison data to support component selection and PCB planning. It also distinguishes exact drop-in options from alternatives that require different memory configurations or package construction.
Pilihan pengganti yang segera untuk ATTINY84-20MU — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera ATTINY84-20MU (sama faktor bentuk dan kaki) — berbeza dalam EEPROM Memory, Flash Memory, PWM Channels, SRAM, Architecture.
ATTINY84A-MU
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ATTINY84A-MMH
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ATTINY84A-MMHR
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ATTINY84-20MU Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | 8-bit AVR Flash Microcontroller |
| Frekuensi Klock Maksimum | 20 MHz |
| Flash Memory | 8 KB (4K x 16 bits) |
| EEPROM Memory | 512 bytes |
| SRAM | 512 bytes |
| General-Purpose I/O Pins | 12 pins |
| ADC Resolution | 10 bits |
| ADC Channels | 8 channels |
| Operating Voltage Range | 2.7 V to 5.5 V |
| Gambaran Suhu Operasi | -40°C to +85°C |
| Timer/Counter Sections | 2 sections (8-bit and 16-bit) |
| PWM Channels | 2 channels per timer/counter section |
| General-Purpose Working Registers | 32 registers |
| Programmable Gain Stage | 1x and 20x gains |
| Kemasan | 20-QFN-EP, 4 x 4 mm |
| Jenis Pemasangan | Surface Mount |
| Program Memory Type | Built-in Flash |
| Architecture | AVR enhanced RISC |
| Status RoHS | Compliant |
Konfigurasi Pin ATTINY84-20MU
| Pin 1 | PA0 — General-purpose I/O and ADC input |
| Pin 2 | PA1 — General-purpose I/O and ADC input |
| Pin 3 | PA2 — General-purpose I/O and ADC input |
| Pin 4 | PA3 — General-purpose I/O and ADC input |
| Pin 5 | PA4 — General-purpose I/O and ADC input |
| Pin 6 | PA5 — General-purpose I/O and ADC input |
| Pin 7 | PA6 — General-purpose I/O and ADC input |
| Pin 8 | PA7 — General-purpose I/O and ADC input |
| Pin 9 | PB0 — General-purpose I/O and timer counter input |
| Pin 10 | PB1 — General-purpose I/O and timer counter input |
| Pin 11 | PB2 — General-purpose I/O and timer counter output |
| Pin 12 | PB3 — General-purpose I/O and timer counter output |
| Pin 13 | VCC — Power supply input |
| Pin 14 | GND — Ground connection |
| Pin 15 | RESET — Active-low reset input |
| Pin 16 | AREF — Analog reference input |
| Pin 17 | AVCC — Analog power supply input |
| Pin 18 | GND — Analog ground connection |
| Pin 19 | NC — Not connected (per datasheet) |
| Pin 20 | NC — Not connected (per datasheet) |
Aplikasi Biasa
ATTINY84-20MU patut untuk 6 aplikasis: Industrial Sensor Node, Battery-Powered Condition Monitor, LED Lighting Controller, Compact Automation Controller, Battery Charger Controller, Instrumentation and Data Logger.
Industrial Sensor Node
The ATTINY84-20MU fits compact industrial sensor nodes because it combines an 8-channel, 10-bit ADC, 12 general-purpose I/O lines, and 8 KB of flash in a 4 x 4 mm package. The microcontroller can sample analog sensors, apply filtering or threshold logic, and transmit status through a serial interface while retaining local control capability. Its 2.7 V to 5.5 V operating range supports both 3.3 V and 5 V sensor platforms. At temperatures from -40°C to +85°C, it is suitable for equipment placed outside climate-controlled enclosures. Design the analog front end around the manufacturer ADC input limits, provide local decoupling, and use the 20 MHz clock only when timing and power requirements justify it.
Disebarkan
Battery-Powered Condition Monitor
The ATTINY84-20MU is well suited to battery-powered condition monitoring because its AVR controller combines 512 bytes of EEPROM, 512 bytes of SRAM, and 8 KB of program memory for compact acquisition and control firmware. The 10-bit ADC can evaluate temperature, voltage, or resistive sensor inputs, while timers and interrupts help schedule measurements without continuous polling. Its low-power TinyAVR architecture can remain active for low-duty-cycle sensing and wake for scheduled or event-driven measurements. The 20-QFN-EP footprint also conserves board area in a wearable or remote-monitoring product. Optimize energy use by running the ADC and unused peripherals only during acquisition, and confirm low-power timing and sleep currents against the manufacturer electrical characteristics.
Disebarkan
LED Lighting Controller
The ATTINY84-20MU can implement compact LED lighting and dimming controllers through its 12 I/O lines and two timer/counter sections with PWM channels. A 20 MHz clock provides timing resolution for animation, status sequences, and adjustable brightness, while 8 KB of flash is sufficient for control tables and moderate user-interface logic. The 2.7 V to 5.5 V range permits use from a regulated 3.3 V rail or a 5 V supply, subject to LED-driver requirements. PWM outputs should drive transistor or driver stages rather than high-current LED strings directly. Check the I/O drive limits, select a current-limiting circuit, and place the MCU decoupling capacitor close to its supply pins to prevent switching-related voltage disturbance.
Disebarkan
Compact Automation Controller
The ATTINY84-20MU supports small automation modules that must combine logic, analog measurement, and timed outputs in a limited board area. Its 8-bit AVR core and 32 working registers are suitable for sequencing, state machines, and basic process-control algorithms, while the 8-channel 10-bit ADC accepts sensor inputs and two timer/counter sections generate timing or PWM outputs. The 20-QFN-EP, 4 x 4 mm package leaves more board area for power conversion and interfaces than a larger controller. For 24 V industrial systems, use a suitable front-end protection and regulation stage rather than connecting the MCU directly to the bus. Validate logic thresholds, isolation boundaries, output drive topology, and restart behavior before connecting actuators.
Disebarkan
Battery Charger Controller
The ATTINY84-20MU can serve as the supervisory controller in a small battery-charging or power-management module because it combines a 20 MHz control core, 8 KB of flash, ADC inputs, timers, and 12 I/O lines. Firmware can monitor battery voltage, control charge-state indicators, sequence external switching stages, and record thresholds in EEPROM. The 512-byte EEPROM is useful for retaining calibration or operating parameters, while the ADC supports analog supervision; however, a dedicated analog front end remains necessary for accurate current measurement and suitable battery limits. Keep the MCU on a regulated rail protected from charger transients, and verify every maximum and minimum electrical limit in the manufacturer documentation before connecting a cell.
Disebarkan
Instrumentation and Data Logger
The ATTINY84-20MU is appropriate for compact instrumentation that records a limited set of measurements and coordinates a serial data link. Its 8-channel 10-bit ADC can acquire several analog channels, and 512 bytes of SRAM supports short acquisition buffers, while 8 KB of flash holds firmware, calibration tables, and a communication protocol. The 20 MHz clock gives sufficient processing headroom for sampled control and framing, and the microcontroller's 12 I/O pins can support status signals, external triggers, and an interface. Storage endurance and write timing should be considered when using EEPROM for frequent logs. Use a serial interface appropriate to the host, define buffer-overrun handling, and preserve a programming route for field upgrades without exposing sensitive test points.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk ATTINY84-20MU — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | ATTINY84A-MU | ATTINY84A-MMH | ATTINY84A-MMHR |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-QFN-EP (4x4) | 20-QFN-EP (4x4) - same | 20-QFN-EP (4x4) - same | 20-QFN-EP (4x4) - same |
| Product Family | ATtiny84 | ATtiny84A | ATtiny84A | ATtiny84A |
| Architecture | 8-bit AVR | 8-bit AVR | 8-bit AVR | 8-bit AVR |
| Flash Memory | 8 KB | 8 KB | 8 KB | 8 KB |
| EEPROM | 512 bytes | 512 bytes | 512 bytes | 512 bytes |
| SRAM | 512 bytes | 512 bytes | 512 bytes | 512 bytes |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
Penyeberangsung Jelas
- Exact ATTINY84 ordering code with 8 KB of flash (vsATTINY84A-MU)
- 20 MHz operation in a compact 4 x 4 mm package (vsATTINY84A-MU)
- 12 I/O pins and an 8-channel 10-bit ADC (vsATTINY84A-MMHR)
Catatan Desain
Place the decoupling capacitor immediately between the VCC and GND pins, with a short return path and minimal loop area. Connect analog decoupling at AVCC and maintain a clean AREF network. Keep switching-node and high-current load paths away from ADC inputs because the 10-bit converter can be sensitive to supply ripple and common-mode disturbance.
Allocate exposed-pad copper according to the manufacturer land-pattern and assembly requirements. Use the package drawing to distinguish the electrical ground pad from any additional package terminals, and verify the stencil and solder-paste design with the contract manufacturer. Uneven exposed-pad soldering can create thermal voids and assembly stress in the 4 x 4 mm QFN package.
Do not treat ATTINY84 and ATTINY84A ordering codes as interchangeable without checking the current manufacturer documentation. Review ADC channels, timer resources, clock options, interrupt behavior, electrical characteristics, errata, and programming requirements. A matching package and 20 MHz clock rating alone do not establish complete firmware or peripheral compatibility.
Select the operating rail so that it remains within 2.7 V to 5.5 V, including transient excursions. For battery systems, verify the minimum regulator output during load changes and prevent deep discharge from pulling the MCU rail below its operating limit. Use the manufacturer sleep and active-current characteristics to estimate battery life rather than relying on nominal clock speed alone.
Maklumat Kesediaan
RoHS compliance is identified in the component listing. The ATtiny84 is an industrial and general-purpose microcontroller, so AEC-Q100 qualification is not applicable.