ATTINY841-MMH - 16MHz 8KB AVR MCU | Microchip Technology
MPN: ATTINY841-MMH ✓ AktifATTINY841-MMH Ringkasan
A microcontroller is a programmable semiconductor that integrates a processor core, memory and peripheral circuits on one die. Within the product hierarchy, the ATTINY841-MMH is an AVR embedded MCU, part of the TinyAVR family, and belongs to the broader 8-bit microcontroller and embedded-controller category. Its compact footprint makes it particularly suitable for small control modules, sensor nodes and compact consumer equipment where every board area matters.
Key features include 8 KB of flash memory for firmware, a 16 MHz operating clock and a 20-pin VQFN package. The ATtiny841 family also supports integrated analog-to-digital conversion, analog comparison and port pin-change interrupt functions. These features allow a design to replace discrete sensing and control circuitry, reducing component count while retaining deterministic firmware-based behavior. The manufacturer lists the ATtiny841 family as in production.
The ATTINY841-MMH uses Microchip's AVR architecture and combines program memory, data EEPROM and SRAM with configurable I/O ports. Port pins support digital input and output as well as alternate functions including analog comparator and ADC channels. The family's 16 MHz operating point provides a practical balance between processing throughput, power consumption and clock design simplicity for embedded control tasks.
Typical applications include compact industrial sensor modules, building and appliance control boards, battery-powered IoT devices, LED lighting controllers and small motor-control subsystems. For motor or relay outputs, designers should account for the load transients and supply requirements of the external driver rather than driving the output directly from the MCU.
A critical layout consideration is the exposed thermal pad on the 20-VQFN package. It must be connected to the intended ground plane and soldered according to the manufacturer's land-pattern and reflow guidance. Place decoupling capacitors close to the supply pins, preserve the recommended clock layout, and route sensitive analog inputs away from fast-switching nodes.
This page combines the manufacturer's device status and datasheet information with practical selection guidance, verified package details, programming references and drop-in alternatives for engineers evaluating the ATTINY841-MMH.
Pilihan pengganti yang segera untuk ATTINY841-MMH — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
ATTINY84A-MMH
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ATTINY441-MMH
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
ATTINY841-MMH Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | 8-bit AVR embedded microcontroller |
| Architecture | AVR |
| Family | ATtiny841 |
| Frekuensi Klock Maksimum | 16 MHz |
| Flash Memory | 8 KB (8K x 8) |
| ADC | Integrated analog-to-digital converter |
| Analog Comparator | Integrated analog comparator |
| Port Pin-Change Interrupts | Supported |
| Bilangan Pin | 20 pins |
| Kemasan | VQFN-20 (3 x 3 mm) |
| Jenis Pemasangan | Surface mount |
| Programmable I/O Port | 8-bit port with pull-up resistors and alternate pin functions |
| Programming Interface | MPLAB PICkit 5 compatible programming and debugging |
| Status Lingkungan Hidup | In production |
Panduan Konfigurasi Pin ATTINY841-MMH vqfn-20 (3 x 3 mm)
Konfigurasi pin untuk ATTINY841-MMH (vqfn-20 (3 x 3 mm) pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk ATTINY841-MMH.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
ATTINY841-MMH patut untuk 6 aplikasis: Compact Industrial Sensor Nodes, Battery-Powered IoT Devices, LED Lighting Control, Appliance Control Boards, Small Motor Control Subsystems, Programmable Logic and Timing Modules.
Compact Industrial Sensor Nodes
The ATTINY841-MMH fits compact industrial sensing modules because its 8 KB flash stores control firmware while the integrated ADC and analog comparator support direct sensor conditioning and threshold decisions. Its 16 MHz clock provides additional timing headroom for sampling, filtering and communication tasks. The 20-VQFN, 3 x 3 mm package also reduces board footprint in space-constrained sensor assemblies. Place the MCU close to the sensor interface, keep analog traces away from switching nodes and validate the ADC reference and grounding strategy against the required measurement accuracy.
Disebarkan
Battery-Powered IoT Devices
The ATTINY841-MMH is appropriate for small battery-powered IoT devices that require local sensing, state-machine control and periodic communications. The 8 KB flash capacity accommodates embedded firmware, and the 16 MHz operating speed supports responsive event handling without the overhead of a larger MCU. Its small VQFN footprint leaves board area for the radio, power conversion and energy-storage components. The design should use the low-power modes described in the family datasheet, disable unused peripherals and measure average current across sleep, wake and radio-transmit intervals.
Disebarkan
LED Lighting Control
The ATTINY841-MMH can implement compact LED lighting control with dimming sequences, current feedback, fault handling and local button or sensor input. Its integrated analog functions allow the controller to monitor a representative LED supply or current-sense signal, while the 16 MHz clock supports timely PWM updates. The 3 x 3 mm VQFN package is useful in dense luminaires and driver boards. Keep high-current LED paths separate from the MCU and analog ground, provide local bulk and high-frequency decoupling, and use suitable transistor or LED-driver circuitry instead of driving the load directly.
Disebarkan
Appliance Control Boards
The ATTINY841-MMH suits compact appliance controllers where a dedicated MCU must coordinate buttons, relays, sensors and timing functions. Its 8 KB flash can hold compact control firmware, and the ADC and analog comparator support input monitoring without additional discrete logic. The 20-VQFN package reduces board area in space-constrained control assemblies. For mains-adjacent or relay-driven equipment, maintain strict separation between low-voltage control circuitry and switching domains. Confirm relay driver ratings, flyback protection, creepage and clearance in accordance with the complete appliance safety design.
Disebarkan
Small Motor Control Subsystems
The ATTINY841-MMH can control small brushed-motor or actuator subsystems where speed, position, current or limit-switch information must be processed locally. The 16 MHz clock supports rapid control updates, and the ADC and analog comparator can support feedback and protection functions. The compact 3 x 3 mm VQFN package fits beneath mechanical assemblies where larger controllers are impractical. The MCU should supervise, not carry, motor current. Use an appropriately rated driver, include flyback or other required protection, isolate noisy motor paths and validate stall current, thermal rise and electromagnetic interference before production release.
Disebarkan
Programmable Logic and Timing Modules
The ATTINY841-MMH can implement compact programmable timers, sequence controllers and logic modules where multiple digital inputs must trigger coordinated outputs. Its 8-bit AVR architecture provides straightforward firmware-based control, while the 16 MHz clock and configurable port interrupts support responsive event handling. The 20-VQFN package enables dense controller placement without requiring a through-hole footprint. Define pin multiplexing carefully, debounce mechanical inputs in firmware or hardware, provide stable clock and reset paths, and use the exposed-pad land pattern required for reliable assembly and thermal performance.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk ATTINY841-MMH — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | ATTINY84A-MMH | ATTINY441-MMH |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | VQFN-20 (3 x 3 mm) | VQFN-20 (3 x 3 mm) | VQFN-20 (3 x 3 mm) |
| Architecture | 8-bit AVR | 8-bit AVR | 8-bit AVR |
| Flash Memory | 8 KB | 8 KB | 6 KB |
| ADC | Integrated | Integrated | Integrated |
| Analog Comparator | Integrated | Integrated | Integrated |
Penyeberangsung Jelas
- Higher flash capacity within the related ATtiny441 package family (vsATTINY441-MMH)
- Higher maximum clock frequency for event handling and control loops (vsATTINY441-MMH)
- Family-specific combination of flash capacity, analog functions and compact packaging (vsATTINY84A-MMH)
Catatan Desain
Use the 20-VQFN land pattern from the manufacturer's package drawing and connect the exposed thermal pad to the designated ground plane. The pad is a major low-inductance return path, so incomplete soldering can increase ground noise and thermal resistance. Follow the manufacturer’s land-pattern, copper, solder-mask and reflow recommendations rather than treating the package as a leadless QFN without thermal design.
Place the required bypass capacitor directly beside the supply and ground pins, with the shortest practical ground connection. Route the clock network away from ADC inputs, relay-driver nodes and other switching traces. Analog inputs should use a quiet return path, and external clock or sensitive-signal traces should avoid crossing high-current power routes to minimize coupling.
Do not treat the same-package alternatives as automatic firmware-compatible devices. Before replacing the ATTINY841-MMH, compare the pin-description table, memory sizes, clock limits, peripheral registers, interrupt vectors, fuse configuration and startup code. The ATtiny841 datasheet's application notes and the programmer's device support list should both be checked before releasing a substitute to production.
Budget the MCU supply separately from loads connected to its I/O pins. Input pins should not exceed the device's specified voltage range, and any externally powered peripheral connected to a GPIO must not back-power an unpowered MCU. Use the family datasheet's supply, reset and input-overvoltage limits when designing the power tree and choosing pull-up resistors.
Maklumat Kesediaan
The manufacturer identifies the ATtiny841 family as in production. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free and conflict-minerals declarations were not identified for the exact package suffix.