ATXMEGA256A3-MH - 32MHz 256KB Flash MCU | Microchip
MPN: ATXMEGA256A3-MH ✓ AktifATXMEGA256A3-MH Ringkasan
An 8/16-bit microcontroller is a compact semiconductor controller designed for embedded control, sensor acquisition, communications, and real-time peripheral management. The AVR enhanced RISC architecture belongs to the wider microcontroller hierarchy: AVR embedded controller, general-purpose processor, and semiconductor. Compared with many larger 32-bit systems, an XMEGA A3 device combines compact code execution with dedicated analog, timing, event, and DMA resources.
The ATXMEGA256A3-MH's principal advantages include 256 KB of Flash for application code, a dedicated 8 KB boot-code section, and a 16 KB SRAM working area. Four DMA channels can transfer data between peripherals and memory, while the eight-channel event system can route events directly to peripherals without continuous processor intervention. These resources suit systems in which deterministic peripheral timing and reduced CPU overhead are important.
Its dual 12-bit ADC supports analog measurements, while the AVR architecture supports both 8-bit and 16-bit instruction operations. The manufacturer describes the family as capable of approaching 1 MIPS per MHz through single-cycle execution. The ATXMEGA256A3-MH therefore balances processing throughput, memory capacity, and peripheral integration without requiring an external coprocessor for many embedded-control workloads.
Typical uses include industrial sensor controllers, communication equipment, data-acquisition systems, compact motor controllers, low-power embedded instruments, and USB-enabled control nodes. Its DMA and event-system resources are particularly useful for simultaneous communication and sampling, while the large Flash capacity supports protocol stacks, bootloaders, and application firmware in one device.
PCB design should preserve short analog and digital return paths, place decoupling capacitors close to the supply pins, and follow the manufacturer pin-description table for the 64-QFN footprint. Verify operating voltage, clock configuration, peripheral pin multiplexing, programming interfaces, and exposed-pad assembly requirements against the manufacturer datasheet before releasing the board layout.
This page combines the ATXMEGA256A3-MH technical specifications, package and memory details, comparison data, application guidance, and practical design considerations to support faster component selection and board-design planning.
Pilihan pengganti yang segera untuk ATXMEGA256A3-MH — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
ATXMEGA256A3U-MH
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ATXMEGA256A3-MH Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | 8/16-bit AVR XMEGA A3 microcontroller |
| Frekuensi Klock Maksimum | 32 MHz |
| Flash Program Memory | 256 KB (128K x 16) |
| Boot Code Section | 8 KB |
| SRAM | 16 KB |
| EEPROM | 4 KB |
| Operating Voltage Range | 1.6 V to 3.6 V |
| ADC Resolution | 12 bit |
| ADC Channel Count | 2 channels |
| DMA Channels | 4 channels |
| Event System Channels | 8 channels |
| Instruction Architecture | AVR enhanced RISC |
| Kemasan | 64-QFN, 9 x 9 mm |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin ATXMEGA256A3-MH 64-qfn, 9 x 9 mm
Konfigurasi pin untuk ATXMEGA256A3-MH (64-qfn, 9 x 9 mm pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk ATXMEGA256A3-MH.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
ATXMEGA256A3-MH patut untuk 6 aplikasis: Industrial Sensor Controller, Data Acquisition System, Communication Controller, Low-Power Embedded Instrument, Compact Motor Controller, USB-Enabled Embedded Node.
Industrial Sensor Controller
The ATXMEGA256A3-MH fits industrial sensor controllers that require local analog measurement, flexible event routing, and enough memory for protocol handling. Its dual 12-bit ADC channels can acquire sensor signals, while the four-channel DMA controller can move sampled data with reduced processor intervention. The eight-channel event system helps connect timing-sensitive events to timers, communication peripherals, or control outputs. With 256 KB Flash, 16 KB SRAM, and 4 KB EEPROM, the controller can retain configuration data and run application firmware locally while operating from 1.6 V to 3.6 V.
Disebarkan
Data Acquisition System
ATXMEGA256A3-MH is well suited to compact data-acquisition systems that need simultaneous control and conversion without a separate digital signal processor. The two 12-bit ADC channels provide the analog front-end interface, while four DMA channels support efficient movement of conversion results into SRAM. The event system can connect timer, communication, and external events without constant polling, helping preserve processor time for filtering and data formatting. Its 32 MHz maximum clock also gives the firmware capacity for calibration tables, communication protocols, and supervisory logic.
Disebarkan
Communication Controller
The ATXMEGA256A3-MH can serve as a protocol and communications controller when a design needs deterministic event handling alongside general embedded control. Its four DMA channels can service buffered transfers, while the eight-channel event system routes timer and peripheral events efficiently. The 256 KB Flash capacity accommodates communication stacks, configuration data, and bootloader code, and 16 KB SRAM supports active transmit and receive buffers. At 1.6 V to 3.6 V, the device is compatible with compact low-voltage interface designs.
Disebarkan
Low-Power Embedded Instrument
ATXMEGA256A3-MH fits battery-powered and low-power embedded instruments that balance processing capability with compact memory use. The 8/16-bit AVR enhanced RISC architecture can execute control and signal-processing tasks at up to 32 MHz, while the 1.6 V minimum operating voltage supports low-voltage supply designs. Four DMA channels and eight event channels reduce the need for continuous processor polling, which can improve responsiveness and energy efficiency. The 4 KB EEPROM is also useful for retaining calibration values, counters, and user settings.
Disebarkan
Compact Motor Controller
The ATXMEGA256A3-MH can coordinate compact motor-control and actuator systems where timing, analog feedback, and local logic must share one controller. Its eight-channel event system supports rapid routing among timers and peripherals, while four DMA channels assist with moving control and status data. Dual 12-bit ADCs can monitor feedback from position, current, or temperature sensors. The 256 KB Flash provides room for motion algorithms, fault handling, parameter storage, and field-upgrade logic, all within a 9 x 9 mm 64-QFN footprint.
Disebarkan
USB-Enabled Embedded Node
ATXMEGA256A3-MH is appropriate for small USB-enabled control nodes that combine protocol firmware with peripheral monitoring. Its 256 KB Flash and 16 KB SRAM provide sufficient space for USB firmware, device configuration, and real-time control functions, while the four-channel DMA controller can reduce transfer overhead. The dual 12-bit ADCs support sensing, and the event system can synchronize external inputs with timer-driven sampling. Designers should confirm the required USB interface pins and board-level transceiver implementation using the manufacturer pin-description table.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk ATXMEGA256A3-MH — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | ATXMEGA256A3U-MH |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 64-QFN (9 x 9 mm) | 64-QFN (9 x 9 mm) |
| Maximum Clock Frequency | 32 MHz | 32 MHz |
| Flash Program Memory | 256 KB | 256 KB |
| SRAM | 16 KB | 16 KB |
| EEPROM | 4 KB | 4 KB |
| ADC Configuration | Dual 12-bit ADC | Dual 12-bit ADC |
| DAC Configuration | 0 channels | 2 continuous output channels |
| DMA and Event System | 4 DMA channels and 8 event channels | 4 DMA channels and 8 event channels |
Penyeberangsung Jelas
- Larger code and working-memory capacity within the XMEGA A3 family (vsATXMEGA256A3U-MH)
- Dedicated event and DMA resources reduce processor polling (vsATXMEGA256A3U-MH)
- Compact surface-mount implementation (vsATXMEGA256A3U-MH)
Catatan Desain
Place the device-side bypass capacitors directly between each supply pin and the nearest ground reference. Route analog inputs away from switching nodes and high-current return paths, and use the manufacturer package drawing to determine the exposed-pad connection. Because the ATXMEGA256A3-MH is a 64-QFN device, verify courtyard clearance, land pattern, solder-mask definition, and assembly paste apertures before fabrication.
Assign ADC, DMA, event-system, and communication signals from the manufacturer pin-description table before fixing the PCB netlist. Several peripheral functions can share pins, so a configuration change can alter the external circuit requirements. Confirm clock source, programming signals, reset behavior, analog references, and boot mode against the intended firmware. Add test points where timing or signal integrity must be validated during production.
Do not treat ATXMEGA256A3U-MH as a feature-identical replacement without reviewing its DAC implementation. The Microchip migration document identifies two continuous DAC channels on the U-family device that are not present on the non-U ATXMEGA256A3. Check analog pin assignments, startup behavior, firmware configuration, and schematic requirements. A shared 64-QFN footprint does not eliminate differences in internal peripheral resources.
Maklumat Kesediaan
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not stated in the product documentation accessed for this entry. AEC-Q100 qualification is not indicated for the general-purpose ATXMEGA256A3-MH ordering code.