Microchip Technology

ATXMEGA256A3-MH - 32MHz 256KB Flash MCU | Microchip

MPN: ATXMEGA256A3-MH ✓ Hoạt động
1.6 V to 3.6 V Vdss 64-QFN, 9 x 9 mm Package 32 MHz Speed 256 KB (128K x 16) Memory
MOQ: 1 |

ATXMEGA256A3-MH Tóm tắt

The Microchip Technology ATXMEGA256A3-MH is a low-power 8/16-bit AVR XMEGA A3 microcontroller operating at up to 32 MHz with 256 KB of self-programming Flash memory in a 64-QFN 9 x 9 mm package. It provides 16 KB SRAM, 4 KB EEPROM, a 4-channel DMA controller, an 8-channel event system, dual 12-bit ADCs, and a 1.6 V to 3.6 V operating-voltage range.

An 8/16-bit microcontroller is a compact semiconductor controller designed for embedded control, sensor acquisition, communications, and real-time peripheral management. The AVR enhanced RISC architecture belongs to the wider microcontroller hierarchy: AVR embedded controller, general-purpose processor, and semiconductor. Compared with many larger 32-bit systems, an XMEGA A3 device combines compact code execution with dedicated analog, timing, event, and DMA resources.

The ATXMEGA256A3-MH's principal advantages include 256 KB of Flash for application code, a dedicated 8 KB boot-code section, and a 16 KB SRAM working area. Four DMA channels can transfer data between peripherals and memory, while the eight-channel event system can route events directly to peripherals without continuous processor intervention. These resources suit systems in which deterministic peripheral timing and reduced CPU overhead are important.

Its dual 12-bit ADC supports analog measurements, while the AVR architecture supports both 8-bit and 16-bit instruction operations. The manufacturer describes the family as capable of approaching 1 MIPS per MHz through single-cycle execution. The ATXMEGA256A3-MH therefore balances processing throughput, memory capacity, and peripheral integration without requiring an external coprocessor for many embedded-control workloads.

Typical uses include industrial sensor controllers, communication equipment, data-acquisition systems, compact motor controllers, low-power embedded instruments, and USB-enabled control nodes. Its DMA and event-system resources are particularly useful for simultaneous communication and sampling, while the large Flash capacity supports protocol stacks, bootloaders, and application firmware in one device.

PCB design should preserve short analog and digital return paths, place decoupling capacitors close to the supply pins, and follow the manufacturer pin-description table for the 64-QFN footprint. Verify operating voltage, clock configuration, peripheral pin multiplexing, programming interfaces, and exposed-pad assembly requirements against the manufacturer datasheet before releasing the board layout.

This page combines the ATXMEGA256A3-MH technical specifications, package and memory details, comparison data, application guidance, and practical design considerations to support faster component selection and board-design planning.

Bộ thay thế dễ dàng lắp đặt cho ATXMEGA256A3-MH — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

ATXMEGA256A3U-MH

✅ Drop-In
📦 64-QFN (9 x 9 mm)
Two continuous DAC output channels are added versus 0 DAC channels on ATXMEGA256A3-MH; core 32 MHz and 256 KB Flash classes are retained

📋 Tham chiếu thay thế (không có trong danh mục)

ATXMEGA256A3-MH Tỷ lệ tối đa & tính chất điện

Product Type 8/16-bit AVR XMEGA A3 microcontroller
Tần số xung maksimum 32 MHz
Flash Program Memory 256 KB (128K x 16)
Boot Code Section 8 KB
SRAM 16 KB
EEPROM 4 KB
Operating Voltage Range 1.6 V to 3.6 V
ADC Resolution 12 bit
ADC Channel Count 2 channels
DMA Channels 4 channels
Event System Channels 8 channels
Instruction Architecture AVR enhanced RISC
Hộp 64-QFN, 9 x 9 mm
Kiểu lắp đặt Surface mount

Hướng dẫn cấu hình chân ATXMEGA256A3-MH 64-qfn, 9 x 9 mm

Cấu hình chân cho ATXMEGA256A3-MH (64-qfn, 9 x 9 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.

Bảng cấu hình chân 64-qfn, 9 x 9 mm cho ATXMEGA256A3-MH

Không có dữ liệu chân cụ thể sẵn có cho ATXMEGA256A3-MH.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

ATXMEGA256A3-MH phù hợp cho 6 Áp dụngs: Industrial Sensor Controller, Data Acquisition System, Communication Controller, Low-Power Embedded Instrument, Compact Motor Controller, USB-Enabled Embedded Node.

🏭

Industrial Sensor Controller

The ATXMEGA256A3-MH fits industrial sensor controllers that require local analog measurement, flexible event routing, and enough memory for protocol handling. Its dual 12-bit ADC channels can acquire sensor signals, while the four-channel DMA controller can move sampled data with reduced processor intervention. The eight-channel event system helps connect timing-sensitive events to timers, communication peripherals, or control outputs. With 256 KB Flash, 16 KB SRAM, and 4 KB EEPROM, the controller can retain configuration data and run application firmware locally while operating from 1.6 V to 3.6 V.

📊

Data Acquisition System

ATXMEGA256A3-MH is well suited to compact data-acquisition systems that need simultaneous control and conversion without a separate digital signal processor. The two 12-bit ADC channels provide the analog front-end interface, while four DMA channels support efficient movement of conversion results into SRAM. The event system can connect timer, communication, and external events without constant polling, helping preserve processor time for filtering and data formatting. Its 32 MHz maximum clock also gives the firmware capacity for calibration tables, communication protocols, and supervisory logic.

🌐

Communication Controller

The ATXMEGA256A3-MH can serve as a protocol and communications controller when a design needs deterministic event handling alongside general embedded control. Its four DMA channels can service buffered transfers, while the eight-channel event system routes timer and peripheral events efficiently. The 256 KB Flash capacity accommodates communication stacks, configuration data, and bootloader code, and 16 KB SRAM supports active transmit and receive buffers. At 1.6 V to 3.6 V, the device is compatible with compact low-voltage interface designs.

🔧

Low-Power Embedded Instrument

ATXMEGA256A3-MH fits battery-powered and low-power embedded instruments that balance processing capability with compact memory use. The 8/16-bit AVR enhanced RISC architecture can execute control and signal-processing tasks at up to 32 MHz, while the 1.6 V minimum operating voltage supports low-voltage supply designs. Four DMA channels and eight event channels reduce the need for continuous processor polling, which can improve responsiveness and energy efficiency. The 4 KB EEPROM is also useful for retaining calibration values, counters, and user settings.

⚡

Compact Motor Controller

The ATXMEGA256A3-MH can coordinate compact motor-control and actuator systems where timing, analog feedback, and local logic must share one controller. Its eight-channel event system supports rapid routing among timers and peripherals, while four DMA channels assist with moving control and status data. Dual 12-bit ADCs can monitor feedback from position, current, or temperature sensors. The 256 KB Flash provides room for motion algorithms, fault handling, parameter storage, and field-upgrade logic, all within a 9 x 9 mm 64-QFN footprint.

🧩

USB-Enabled Embedded Node

ATXMEGA256A3-MH is appropriate for small USB-enabled control nodes that combine protocol firmware with peripheral monitoring. Its 256 KB Flash and 16 KB SRAM provide sufficient space for USB firmware, device configuration, and real-time control functions, while the four-channel DMA controller can reduce transfer overhead. The dual 12-bit ADCs support sensing, and the event system can synchronize external inputs with timer-driven sampling. Designers should confirm the required USB interface pins and board-level transceiver implementation using the manufacturer pin-description table.

Tóm tắt các sản phẩm được đề xuất

ATXMEGA256A3 Base XMEGA A3 device family Được sử dụng trong: Industrial Sensor Controller, Data Acquisition System, Communication Controller, Low-Power Embedded Instrument, Compact Motor Controller, USB-Enabled Embedded Node ATXMEGA256A3U-MH Same-family variant with DAC channels Được sử dụng trong: Industrial Sensor Controller, Data Acquisition System, Communication Controller, Low-Power Embedded Instrument, Compact Motor Controller, USB-Enabled Embedded Node
What are the key specifications of ATXMEGA256A3-MH that engineers should know?
The ATXMEGA256A3-MH is a 32 MHz, 8/16-bit AVR XMEGA A3 microcontroller with 256 KB Flash, 16 KB SRAM, and 4 KB EEPROM. According to the Microchip manufacturer datasheet, it also includes a 4-channel DMA controller, an 8-channel event system, dual 12-bit ADCs, and a 1.6 V to 3.6 V operating-voltage range. Its 64-QFN package measures 9 x 9 mm, making it suitable for compact embedded-control and signal-acquisition boards.
What is the operating voltage range of ATXMEGA256A3-MH?
The ATXMEGA256A3-MH operates from 1.6 V to 3.6 V. According to the Microchip manufacturer datasheet and product listing, this range applies to the 8/16-bit XMEGA A3 device in its 64-QFN package. The supply selection must also account for clock frequency and peripheral activity. Use a stable regulated rail and place local bypass capacitors close to the device's supply pins to minimize transient disturbance on sensitive analog and digital circuits.
How much memory does ATXMEGA256A3-MH have?
The ATXMEGA256A3-MH provides 256 KB of self-programming Flash program memory, organized as 128K x 16, together with 16 KB of SRAM and 4 KB of EEPROM. According to the Microchip manufacturer product page, Flash also includes an 8 KB boot-code section. This combination supports application firmware, bootloader code, working data, and nonvolatile parameter storage within one microcontroller.
What peripherals are integrated into ATXMEGA256A3-MH?
The ATXMEGA256A3-MH integrates a four-channel DMA controller, an eight-channel event system, and two 12-bit ADC channels. According to the Microchip manufacturer product page, the DMA and event system can move peripheral data and route events with limited CPU intervention. These resources help isolate time-sensitive sampling, communications, and control functions from the main instruction stream in embedded systems.
Where can I download the ATXMEGA256A3-MH datasheet PDF?
The ATXMEGA256A3-MH datasheet PDF is available from the Microchip Technology device-documentation website. According to the manufacturer publication, the document contains part-specific electrical characteristics, peripheral descriptions, and package information. Use the same document to confirm the complete 64-QFN pin description, clock limits, absolute maximum ratings, programming connections, and PCB recommendations before finalizing a design.
Where can I find the ATXMEGA256A3-MH pinout?
The ATXMEGA256A3-MH pinout is defined by the Microchip manufacturer datasheet for the 64-QFN 9 x 9 mm package. Use the package drawing and pin-description table to assign power, ground, reset, clock, programming, analog, and peripheral signals. Include the exposed-pad connection and its thermal requirements in the board design, and verify every signal against the selected clock and peripheral configuration.
Is ATXMEGA256A3-MH suitable for industrial sensor and acquisition systems?
The ATXMEGA256A3-MH is suitable for compact sensor and acquisition systems requiring local conversion, deterministic peripheral routing, and modest firmware storage. According to the Microchip manufacturer datasheet, the device provides dual 12-bit ADCs, four DMA channels, an eight-channel event system, 256 KB Flash, and 16 KB SRAM. Its 1.6 V to 3.6 V range supports low-voltage designs, while the 64-QFN footprint supports space-constrained boards.
What can replace ATXMEGA256A3-MH without changing the PCB footprint?
ATXMEGA256A3U-MH is a same-package candidate from the Microchip XMEGA A3 family, but its DAC functionality differs from the non-U ATXMEGA256A3-MH. The manufacturer migration document identifies different DAC arrangements between the U and non-U devices, so firmware and analog-signal assignments must be reviewed before substitution. A footprint match alone does not guarantee identical peripheral behavior, and a qualified second-source part should be confirmed against the complete pin-description table.
Is ATXMEGA256A3-MH the same as ATXMEGA256A3U-MH?
No, ATXMEGA256A3-MH and ATXMEGA256A3U-MH are related but not identical in peripheral configuration. According to the Microchip migration document, the ATxmega256A3U family includes two continuous DAC output channels, whereas the non-U ATxmega256A3 family does not. Both belong to the XMEGA A3 family, but analog-pin assignments, firmware configuration, and board-level signal use must be checked before treating the U variant as a replacement.
When should I choose ATXMEGA256A3-MH over a smaller AVR microcontroller?
Choose the ATXMEGA256A3-MH when the design needs more code space, SRAM, DMA, or event routing than a smaller AVR can provide. According to the Microchip manufacturer product page, it offers 256 KB Flash, 16 KB SRAM, four DMA channels, and an eight-channel event system. A smaller AVR may remain preferable for simple, cost-sensitive control with modest memory needs, while the XMEGA A3 is better matched to multi-peripheral and data-moving designs.
ATXMEGA256A3-MH vs ATXMEGA256A3U-MH: which is better for DAC control?
ATXMEGA256A3U-MH is the better choice when the application requires the device's two continuous DAC output channels. According to the Microchip migration document, the U-family ATxmega256A3 device includes the DAC arrangement that the non-U ATXMEGA256A3 lacks. ATXMEGA256A3-MH remains appropriate when the design uses ADCs, timers, communications, DMA, and event-system functions without requiring onboard DAC outputs.
What is the best Microchip alternative for ATXMEGA256A3-MH?
ATXMEGA256A3U-MH is the closest identified same-package Microchip alternative for ATXMEGA256A3-MH, but it is not a feature-identical substitute. According to the Microchip migration document, the U variant adds two continuous DAC output channels that are absent from the non-U device. Review analog-pin assignments, DAC resource allocation, firmware initialization, and schematic requirements before approving it as a replacement.
Where can I buy ATXMEGA256A3-MH online?
Use the Request a Quote form on this page to ask for ATXMEGA256A3-MH availability, current commercial terms, and delivery scheduling. The request should include the exact MPN, ATXMEGA256A3-MH, the required 64-QFN package, and your production quantity. Providing the target quantity and schedule helps the supplier confirm assembly, traceability, and lead-time requirements without relying on an outdated catalog listing.
What is the price of ATXMEGA256A3-MH?
Current ATXMEGA256A3-MH commercial pricing is not published as a fixed table on this page. Use the Request a Quote form to request a unit quotation and volume breaks for the exact 64-QFN ordering code. Include your annual usage, prototype or production quantity, and required delivery date. This keeps the commercial response aligned with the requested package and procurement schedule.
What is the lead time and stock status for ATXMEGA256A3-MH?
Request the current stock position, minimum order quantity, and lead time for ATXMEGA256A3-MH through the Request a Quote form on this page. Include the exact MPN, target quantity, and required delivery date in the request. For production planning, also confirm whether the shipment must be reel-packed, traceable, or accompanied by a manufacturer certificate of conformance.

Dữ liệu tham khảo kỹ thuật cho ATXMEGA256A3-MH — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose ATXMEGA256A3-MH when the design requires dual 12-bit ADC channels, four DMA channels, an eight-channel event system, 256 KB Flash, 16 KB SRAM, and 4 KB EEPROM without onboard DAC outputs. It is a strong fit for industrial sensing, communication nodes, compact instruments, and embedded control systems operating from 1.6 V to 3.6 V. ATXMEGA256A3U-MH is the relevant same-package alternative when two continuous DAC output channels are needed, but its analog pin allocation and firmware setup must be reviewed because it is not feature-identical. If the design only requires basic control with limited memory, a smaller 8-bit AVR may reduce complexity and board area. If it requires substantially greater processing power, larger RAM, or more advanced connectivity, move beyond the 8/16-bit XMEGA class and evaluate a 32-bit MCU against the complete peripheral and software requirements.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này ATXMEGA256A3U-MH
Brand Microchip Technology Microchip Technology
Package 64-QFN (9 x 9 mm) 64-QFN (9 x 9 mm)
Maximum Clock Frequency 32 MHz 32 MHz
Flash Program Memory 256 KB 256 KB
SRAM 16 KB 16 KB
EEPROM 4 KB 4 KB
ADC Configuration Dual 12-bit ADC Dual 12-bit ADC
DAC Configuration 0 channels 2 continuous output channels
DMA and Event System 4 DMA channels and 8 event channels 4 DMA channels and 8 event channels

Bảo phân biệt quan trọng

  • Larger code and working-memory capacity within the XMEGA A3 family (vsATXMEGA256A3U-MH)
  • Dedicated event and DMA resources reduce processor polling (vsATXMEGA256A3U-MH)
  • Compact surface-mount implementation (vsATXMEGA256A3U-MH)

Ghi chú thiết kế

Place the device-side bypass capacitors directly between each supply pin and the nearest ground reference. Route analog inputs away from switching nodes and high-current return paths, and use the manufacturer package drawing to determine the exposed-pad connection. Because the ATXMEGA256A3-MH is a 64-QFN device, verify courtyard clearance, land pattern, solder-mask definition, and assembly paste apertures before fabrication.

Assign ADC, DMA, event-system, and communication signals from the manufacturer pin-description table before fixing the PCB netlist. Several peripheral functions can share pins, so a configuration change can alter the external circuit requirements. Confirm clock source, programming signals, reset behavior, analog references, and boot mode against the intended firmware. Add test points where timing or signal integrity must be validated during production.

Do not treat ATXMEGA256A3U-MH as a feature-identical replacement without reviewing its DAC implementation. The Microchip migration document identifies two continuous DAC channels on the U-family device that are not present on the non-U ATXMEGA256A3. Check analog pin assignments, startup behavior, firmware configuration, and schematic requirements. A shared 64-QFN footprint does not eliminate differences in internal peripheral resources.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not stated in the product documentation accessed for this entry. AEC-Q100 qualification is not indicated for the general-purpose ATXMEGA256A3-MH ordering code.

Dữ liệu được xác minh vào: 2026-11-16 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

ATXMEGA256A3-MH datasheet ATXMEGA256A3-MH pinout ATXMEGA256A3-MH datasheet pdf ATXMEGA256A3-MH specifications ATXMEGA256A3-MH equivalent ATXMEGA256A3-MH replacement ATXMEGA256A3-MH price ATXMEGA256A3-MH stock ATXMEGA256A3 64-QFN pinout ATXMEGA256A3-MH vs ATXMEGA256A3U-MH Microchip ATXMEGA256A3-MH ATXMEGA256A3-MH ADC DMA

Các bộ phận và thuật ngữ liên quan

Microchip Technology ATXMEGA256A3-MH ATXMEGA256A3 ATXMEGA256A3U-MH AVR AVR enhanced RISC architecture XMEGA A3 8/16-bit microcontroller microcontroller semiconductor embedded controller 64-QFN QFN package family surface-mount package 256 KB Flash 16 KB SRAM 4 KB EEPROM 4-channel DMA controller 8-channel event system dual 12-bit ADC 1.6 V to 3.6 V 32 MHz industrial sensor controller data acquisition system communication controller
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ