C8051F582-IQ - 50MHz 128KB Automotive 8051 MCU | Silicon Labs
MPN: C8051F582-IQ ✓ AktifC8051F582-IQ Ringkasan
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into a single chip. The C8051F58x family belongs to the 8051 embedded-control hierarchy, where each device executes firmware to monitor inputs, process data, and control outputs. The C8051F582-IQ extends this architecture with automotive-oriented mixed-signal and network functionality suitable for distributed electronic control units, sensor interfaces, and CAN-to-LIN gateway equipment.
Key features include a maximum 50 MHz clock, 128 KB Flash, 8 KB RAM, CAN 2.0, LIN 2.1, SPI, two UARTs, and I2C. A dedicated VIO pin permits the Port I/O and reset interface to operate with 5 V logic while the internal core runs from a lower supply. The mixed-signal section provides an ADC with programmable gain and a 200 ksps class throughput, supporting compact automotive sensing and control functions without requiring a separate analog processor.
The device uses the Silicon Labs C8051 instruction set and retains the familiar 8051 core while integrating more capable communication, timing, and analog blocks. Its 32-pin QFP package exposes the required communications, digital I/O, analog inputs, clock, reset, and power connections in a widely supported surface-mount format. Pin-compatible family options allow designers to balance peripheral requirements while retaining a common PCB footprint.
Typical applications include CAN-to-LIN gateways, body-control modules, automotive sensor controllers, actuator drivers, industrial communication nodes, and mixed-signal monitoring systems. Its combination of CAN, LIN, analog conversion, and 8051-compatible software support targets distributed networks where space, deterministic control, and multiple interface types are important.
When laying out the PCB, treat the VIO supply independently from the main core supply and provide the decoupling, oscillator, and programming-interface connections recommended by the manufacturer datasheet. Confirm startup, reset, and 5 V I/O behavior in the final vehicle or industrial electrical environment.
This page consolidates the device identity, interface capabilities, family-package information, sourcing path, and practical replacement considerations. It also identifies where alternate family members require application-level verification rather than implying that every C8051F58x device is interchangeable.
Pilihan pengganti yang segera untuk C8051F582-IQ — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera C8051F582-IQ (sama faktor bentuk dan kaki) — berbeza dalam Package, Product Type, ADC Resolution, Flash Memory, Serial Interfaces.
C8051F583-IQ
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →C8051F586-IQ
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
C8051F587-IQ
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
C8051F582-IQ Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | 8-bit automotive and industrial microcontroller |
| Architecture | C8051 8051-compatible MCU |
| Frekuensi Klock Maksimum | 50 MHz |
| Maximum Throughput | 50 MIPS |
| Program Flash Memory | 128 KB |
| RAM Memory | 8 KB |
| Supply Voltage Options | 2.5 V, 3.3 V, or 5 V |
| External I/O Logic Voltage | 5 V |
| CAN Interface | CAN 2.0 |
| LIN Interface | LIN 2.1 |
| SPI Interface | 1 SPI interface |
| UART Interface | 2 UART interfaces |
| I2C Interface | 1 I2C interface |
| ADC Resolution | 12-bit |
| ADC Throughput | 200 ksps |
| ADC Integral Nonlinearity | ±1 LSB |
| Kemasan | 32-pin QFP |
| Jenis Pemasangan | Surface mount |
| Programmable Hysteresis | Supported |
Panduan Konfigurasi Pin C8051F582-IQ 32-pin qfp
Konfigurasi pin untuk C8051F582-IQ (32-pin qfp pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk C8051F582-IQ.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
C8051F582-IQ patut untuk 6 aplikasis: Automotive CAN-to-LIN Gateway, Vehicle Body-Control Module, Automotive Sensor Controller, Industrial Communication Node, Actuator and Relay Control, Mixed-Signal Monitoring System.
Automotive CAN-to-LIN Gateway
The C8051F582-IQ suits an automotive gateway because it combines CAN 2.0, LIN 2.1, a 50 MHz 8051-compatible core, 128 KB Flash, and 8 KB RAM in a 32-pin QFP. The MCU can manage protocol translation, diagnostic routines, and coordination between CAN-connected body modules and LIN-attached sensors or actuators. Its 12-bit ADC supports local analog supervision, while the programmable digital peripherals support debouncing and event-driven control. Separate CAN and LIN transceivers, protection networks, and vehicle-specific isolation or filtering remain required. Firmware should include bus-off recovery, timeout handling, and message validation rather than assuming that the MCU-side interface provides complete network protection.
Disebarkan
Vehicle Body-Control Module
The C8051F582-IQ provides a practical combination of control performance and communication for space-constrained body-control modules. Its 50 MHz processing capability supports deterministic state-machine execution, while 128 KB Flash provides room for application firmware and 8 KB RAM supports protocol buffers and diagnostic data. CAN and LIN connectivity allows the controller to participate in both vehicle network segments, and the 12-bit ADC can monitor resistive sensors or analog feedback. The 32-pin QFP package also reduces reliance on external logic when compared with a larger general-purpose MCU. Production design work must verify wake behavior, reset handling, 5 V I/O compatibility through VIO, and the exact automotive qualification conditions for the -IQ ordering code.
Disebarkan
Automotive Sensor Controller
The C8051F582-IQ fits distributed sensor-controller duties where an embedded 8051 core must combine measurement and network communication in one package. Its 12-bit ADC operates at up to 200 ksps and includes programmable gain, allowing input signals to use more of the converter range before digital scaling. The device can filter and qualify sensor readings, apply hysteresis, and report events through CAN or LIN. The 50 MHz core has ample throughput for calibration handling and diagnostics, while 128 KB Flash supports local tables and algorithms. Keep analog routing away from high-speed communication nets, follow the manufacturer grounding recommendations, and confirm whether the required sensor bandwidth needs filtering beyond the converter’s raw sampling capability.
Disebarkan
Industrial Communication Node
The C8051F582-IQ can serve as a compact industrial communications node when a design needs both CAN and LIN along with local control and analog measurement. Its 50 MHz 8051-compatible execution core can service multiple protocol tasks, while 128 KB Flash accommodates communication stacks and application logic. SPI, two UARTs, and I2C provide additional paths for sensors, memory, and service interfaces. The 32-pin QFP package is appropriate for industrial controller boards requiring a conventional, inspectable leaded surface-mount footprint. Firmware should include deterministic scheduling, CRC or frame validation, bus timeout recovery, and diagnostic counters. For harsh environments, validate transient immunity, operating-temperature limits, isolation strategy, and grounding against the complete system specification.
Disebarkan
Actuator and Relay Control
The C8051F582-IQ is appropriate for compact actuator-control modules that need local feedback and vehicle-network coordination. Its 12-bit ADC can monitor current, position, or resistive feedback, while programmable hysteresis helps define robust switching thresholds around noisy or slowly changing sensor signals. The 50 MHz core supports debounce logic, timing sequences, fault counters, and communication response tasks. CAN and LIN allow the controller to accept commands and report operating status without a separate network processor. The 32-pin QFP provides access to the required control signals while keeping the footprint manageable for multi-board assemblies. Add suitable driver transistors or interface drivers, flyback protection for inductive loads, and analog conditioning; the MCU itself is not a direct power-stage device.
Disebarkan
Mixed-Signal Monitoring System
The C8051F582-IQ supports mixed-signal monitoring functions that combine periodic ADC sampling with communications and local logic. Its 12-bit converter, programmable gain, and 200 ksps throughput can acquire analog sensor data, while the 50 MHz core performs filtering, threshold evaluation, and event logging. CAN, LIN, SPI, UART, and I2C allow the same controller to interface with networked sensors, local transceivers, and configuration storage. The 128 KB Flash and 8 KB RAM provide resources for calibration coefficients and short-term data buffering. Place the analog input path close to the converter pins, maintain the recommended analog and digital ground arrangement, and validate sampled signals with appropriate anti-alias filtering. Calibration code should retain raw and filtered values so field diagnostics can distinguish sensor faults from processing errors.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk C8051F582-IQ — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | C8051F583-IQ | C8051F586-IQ | C8051F587-IQ |
|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 32-pin QFP | 32-pin QFP | 32-pin QFP | 32-pin QFP |
| Maximum Clock Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Core Architecture | 8051-compatible C8051 | 8051-compatible C8051 | 8051-compatible C8051 | 8051-compatible C8051 |
| CAN Interface | CAN 2.0 | CAN 2.0 | CAN 2.0 | CAN 2.0 |
| LIN Interface | LIN 2.1 | LIN 2.1 | LIN 2.1 | LIN 2.1 |
| Supply Voltage Options | 2.5 V, 3.3 V, or 5 V | 2.5 V, 3.3 V, or 5 V | 2.5 V, 3.3 V, or 5 V | 2.5 V, 3.3 V, or 5 V |
Penyeberangsung Jelas
- Integrated CAN and LIN connectivity (vsC8051F586-IQ)
- Mixed-signal capability in a 32-pin package (vsC8051F587-IQ)
- 50 MHz processing with 128 KB Flash (vsC8051F583-IQ)
Catatan Desain
Power VDD and the VIO domain as separate rails in the schematic. The manufacturer states that Port I/O and RST can interface with 5 V logic when VIO is set to 5 V. Follow the data sheet for allowable combinations, decoupling capacitance, sequencing, and power-state limits. Do not assume that a 5 V VIO setting changes the internal core supply requirement or permits every peripheral pin to tolerate unrestricted 5 V.
Keep the 32-pin QFP footprint mechanically compatible with the exact -IQ ordering code and route sensitive analog inputs away from CAN, LIN, SPI, UART, and clock nets. Place decoupling capacitors at the supply pins according to the manufacturer layout guidance, provide a low-impedance ground plane, and reserve programming and debug access. Because the -IM version uses a 5 mm by 5 mm QFN package, it must not be placed on the same land pattern as the -IQ QFP device.
Treat communication interfaces as digital signals even when they originate from a slow control system. Respect setup and hold timing, drive-strength, input-threshold, and maximum-pin-voltage limits in the data sheet, and use series damping where edge rates or routed lengths could cause ringing. For analog measurements, use local filtering and a quiet return path so CAN and LIN switching activity does not disturb the 12-bit ADC input and programmable-gain threshold decisions.
A common mistake is treating all C8051F58x suffix variants as interchangeable. Compare the exact ordering code, package drawing, pin table, ADC resources, communication ports, memory configuration, clock requirements, and qualification before substitution. In particular, C8051F582-IQ is a 32-pin QFP ordering code, while C8051F582-IM is associated with a 32-QFN 5 mm by 5 mm package; those choices require different PCB footprints despite sharing the same family name.
Maklumat Kesediaan
The device is described as an automotive microcontroller, but exact RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements for the C8051F582-IQ ordering code require confirmation from the manufacturer product documentation or declaration.