CD4060AF/3 - 14-Stage CMOS Counter | Texas Instruments
MPN: CD4060AF/3 ✓ AktifCD4060AF/3 Ringkasan
A CMOS ripple-carry counter is a sequential digital logic device that increments or decrements its binary state on each active clock edge. The CD4060 family combines this counter function with an oscillator and divider outputs in one integrated circuit. In the system hierarchy, it belongs to the CMOS logic family, within counters and dividers, and ultimately within integrated digital logic ICs. Its ability to derive multiple divided clocks from one oscillator reduces the number of separate timing components required in timer and waveform-generation circuits.
The principal features include 14 counter stages, a 4 MHz maximum operating frequency, a single counter element, falling-edge triggering, and a supply range of 3 V to 12 V. The RCA CD4060AF documentation describes a temperature range of -55°C to 125°C, making the family suitable for industrial and extended-temperature equipment where its qualification level permits. The counter also includes reset and oscillator-related terminals for initialization and clock-source control.
Internally, the ripple-carry architecture propagates each count transition through successive stages. Outputs from Q0 through Q9 are normally used for relatively high division ratios, while the later stages provide division by progressively larger powers of two. When the internal oscillator is used, its timing accuracy depends on the external resistor and capacitor network, component tolerance, temperature behavior, and stray capacitance. These characteristics distinguish the CD4060AF/3 from ordinary binary counters that require a separate clock generator.
Typical uses include digital timers, pulse generators, frequency dividers, delayed-event logic, clock qualification, and industrial control circuits. It is also useful as a frequency-divider stage in a larger timing chain because multiple binary outputs are available from the same package. When cascading counters, designers should account for propagation delay through the ripple stages and ensure that the downstream device has suitable setup and hold timing.
The principal design consideration is power-supply and clocking discipline. Place the supply bypass capacitor close to VDD and VSS, keep oscillator components close to OSC IN and OSC OUT, and avoid long traces around high-impedance timing nodes. The 3 V to 12 V operating range supports legacy CMOS systems, but modern designs must account for the absence of modern-level input overvoltage tolerance unless the manufacturer confirms otherwise.
This product page combines the CD4060AF/3 device identity, package information, operating limits, replacement considerations, application guidance, and practical implementation notes. It also identifies which technical attributes are established by the manufacturer documentation and which replacement details require comparison against the selected candidate's own datasheet.
Pilihan pengganti yang segera untuk CD4060AF/3 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
CD4060B-MIL
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
CD4060AF
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
CD4060AF/3 Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | CMOS 14-stage ripple-carry binary counter/divider and oscillator |
| Counter Stages | 14 stages |
| Counter Element Count | 1 element |
| Counting Mode | Binary |
| Counting Edge | Falling edge |
| Supply Voltage Range | 3 V to 12 V |
| Maximum Operating Frequency | 4 MHz |
| Jenis Output | 14-bit binary counter/divider output |
| Oscillator | Integrated RC oscillator |
| Reset Function | Asynchronous reset |
| Kemasan | 16-pin CDIP |
| Terminal Count | 16 terminals |
| Jenis Pemasangan | Through-hole dual in-line |
| JEDEC Package Code | R-XDIP-T16 |
| Temperature Range | -55°C to 125°C |
| Logic Family | CMOS |
Konfigurasi Pin CD4060AF/3
| Pin 1 | CLK — Clock input for counter stage |
| Pin 2 | CLK IN — External clock input |
| Pin 3 | Q10 — Counter output |
| Pin 4 | Q11 — Counter output |
| Pin 5 | Q12 — Counter output |
| Pin 6 | Q13 — Counter output |
| Pin 7 | Q14 — Counter output |
| Pin 8 | VSS — Ground supply terminal |
| Pin 9 | OSC OUT — Oscillator output |
| Pin 10 | OSC IN — Oscillator input |
| Pin 11 | RESET — Counter reset input |
| Pin 12 | Q0 — Counter output |
| Pin 13 | Q1 — Counter output |
| Pin 14 | Q2 — Counter output |
| Pin 15 | Q3 — Counter output |
| Pin 16 | VDD — Positive supply terminal |
Aplikasi Biasa
CD4060AF/3 patut untuk 6 aplikasis: Industrial Timer and Delay Generator, Frequency Divider and Clock Qualification, Pulse and Tone Generation, Digital Logic Retiming, Test and Measurement Equipment, Embedded Sequential Control.
Industrial Timer and Delay Generator
The CD4060AF/3 fits industrial timer and delay circuits because it combines an oscillator with 14 stages of ripple-carry counting in one 16-pin CDIP package. An external resistor-capacitor network can establish the oscillator timing, and the counter outputs provide successive binary division points for delay selection. Operating from 3 V to 12 V with a 4 MHz maximum operating frequency supports conventional CMOS control systems. In operation, the timer can trigger discrete logic stages as the binary count progresses, reducing the number of separate cascaded flip-flops required. Designers should verify oscillator accuracy against the tolerance and temperature coefficient of the timing components and allow for ripple propagation delay when the output must switch a downstream device immediately.
Disebarkan
Frequency Divider and Clock Qualification
The CD4060AF/3 is appropriate for dividing a clock into lower-rate timing signals because its 14 ripple stages expose multiple binary division outputs. With operation up to 4 MHz, the device can process suitable CMOS clock signals while the 3 V to 12 V range supports legacy equipment rails. The divided outputs can gate counters, data-capture circuits, or sequential test functions without requiring a separate binary divider for every ratio. A key design consideration is the accumulated propagation delay through the ripple stages, which becomes more important when the downstream logic has short setup requirements. Confirm the input transition shape, output rise and fall times, supply level, and maximum clock frequency before treating the counter output as a clean replacement for a modern high-speed clock divider.
Disebarkan
Pulse and Tone Generation
The CD4060AF/3 can generate repetitive pulses or coarse timing waveforms by combining its internal oscillator with selected divider outputs. Its 14-stage binary count permits widely separated pulse rates to be selected without a bank of independent oscillators, and the 3 V to 12 V supply range matches conventional CMOS logic systems. In a pulse-generation circuit, one Q output provides the repetition signal while another output may serve as a delayed enable or synchronized pulse. Accuracy is set primarily by the external oscillator components and their behavior over temperature, not only by the nominal 4 MHz counter capability. Use the manufacturer oscillator guidance, observe output drive requirements, and ensure any connected CMOS load does not exceed the available output-current and capacitance limits.
Disebarkan
Digital Logic Retiming
The CD4060AF/3 can provide coarse digital retiming when a system needs delayed transitions derived from an external clock. The falling-edge counting behavior allows an external event to advance the counter, while outputs become available at successive binary intervals. This approach is useful in legacy control, test, and sequencing equipment where a large number of timing taps would otherwise require separate delay logic. The device supports input frequencies up to 4 MHz, but each additional stage adds ripple delay, so critical outputs should be timed against the actual counter transitions rather than assumed to switch simultaneously. The 16-pin CDIP package supports through-hole construction and straightforward replacement in existing legacy boards, subject to exact pinout and qualification verification.
Disebarkan
Test and Measurement Equipment
The CD4060AF/3 is suitable for legacy test and measurement equipment that requires a compact clock divider, programmable delay, or repetitive trigger source. Multiple binary outputs allow several test points to observe related timing phases, and the integrated oscillator reduces the component count compared with a separate clock generator and divider. Its 3 V to 12 V operating range and 4 MHz maximum frequency align with classic CMOS test logic, while the 16-pin CDIP package facilitates use in existing through-hole fixtures. Measurement accuracy depends on the oscillator network and component tolerances. For instrumentation requiring calibrated frequency accuracy, calibrate the timing network against a reference and use Schmitt-trigger input conditioning where necessary to prevent false clock transitions.
Disebarkan
Embedded Sequential Control
The CD4060AF/3 can act as a compact sequential-control element in legacy embedded systems, especially when a long timing sequence is needed from a small number of external outputs. Each counter transition advances the machine state, allowing different loads, relays, or data-capture stages to be activated at selected binary counts. The device's 14 counter stages and integrated oscillator simplify long-duration control sequences, while its 3 V to 12 V supply range supports older control voltage levels. Ripple delay should be included in the control timing budget because outputs change sequentially rather than simultaneously. Confirm reset polarity, oscillator startup behavior, output load, and transition timing in the target system before using the counter as the master sequencer for safety- or timing-critical operations.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk CD4060AF/3 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | CD4060B-MIL | CD4060AF |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | RCA |
| Package | 16-pin CDIP | 16-pin CDIP | 16-pin DIP |
| Product Function | 14-stage ripple-carry binary counter/divider and oscillator | 14-stage ripple-carry binary counter/divider and oscillator | CMOS 16-bit binary counter family device |
Penyeberangsung Jelas
- Provides 14 division stages in one timing IC (vsCD4060B-MIL)
- Uses a 16-terminal through-hole counter package (vsCD4060AF)
- Documents a 4 MHz maximum operating frequency (vsCD4060AF)
Catatan Desain
Place the supply bypass capacitor as close as practical to the VDD and VSS terminals, and route the return current directly to the device ground. The 3 V to 12 V operating range does not remove the need for stable rail voltage because oscillator frequency, switching speed, and output thresholds depend on VDD. Check the counter's dynamic output current and total CMOS input load before adding fan-out, especially when several Q outputs drive another legacy CMOS gate.
Keep the external oscillator resistor and capacitor close to OSC IN and OSC OUT, and minimize the loop area of the timing network. Long PCB traces can add parasitic capacitance that changes the nominal oscillator frequency. If the oscillator must meet a calibrated tolerance, use tight-tolerance components, account for their temperature coefficients, and provide a ground plane that does not interrupt the oscillator's return path.
Do not treat every 14-bit counter value as available at a dedicated output, and do not assume all Q outputs change simultaneously. The 16-pin package exposes only 16 terminals, including power and control functions, and ripple transitions propagate through successive stages. Use the manufacturer pin-description table when assigning outputs and include accumulated propagation delay when driving a downstream latch, flip-flop, or pulse-capture circuit.
An external clock should have clean transitions and satisfy the device's input-level requirements at the selected supply voltage. Long interconnects can add ringing, coupling, or differential delay that produces an unintended extra edge. When replacing an existing CD4060AF/3, inspect the original clock source for asymmetric rise and fall times and preserve any series resistance or conditioning already used to protect the input.
Maklumat Kesediaan
The available device documentation identifies the CD4060AF/3 as a CMOS logic counter/divider and oscillator, but it does not establish RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. CD4060AF/3 is a general-purpose logic device rather than an automotive-qualified AEC-Q100 product.