DG442DY+T - 4-Channel SPST Analog Switch | Analog Devices
MPN: DG442DY+T ✓ AktifDG442DY+T Ringkasan
An analog switch is an electrically controlled semiconductor device that connects or disconnects an analog signal path. The DG442 belongs to the analog-switch hierarchy, which also includes multiplexers, selectors, and matrix switches. Unlike a mechanical relay, it can change state rapidly without mechanical wear. Its four independent SPST channels provide separate signal paths while sharing common positive and negative supply rails.
The DG442DY+T uses TTL-compatible and CMOS-compatible control inputs, allowing its digital control signals to be driven by common microcontrollers, FPGA logic, comparators, and other digital controllers. Its 85 ohm on-resistance is suitable for many moderate-impedance instrumentation and test circuits. The 1:1 configuration means that each switched path presents one on-resistance rather than dividing a signal through a multiplexer network.
The Renesas DG441 and DG442 family datasheet identifies the DG442 as a CMOS analog switch with four independent SPST channels and a voltage reference for logic thresholds. These characteristics make the part appropriate when deterministic control logic and repeatable analog-path routing are required. The improved DG442 positioning is relevant when upgrading systems that used older DG201A and DG202-family switches.
Typical uses include multimeter and oscilloscope input routing, automated test equipment, data-acquisition modules, sample-and-hold circuits, battery-powered instruments, and industrial control systems. The device can route low-frequency baseband signals without the switching transients associated with electromechanical relays. Applications should still verify signal amplitude, bandwidth, charge injection, leakage, and power-supply limits against the manufacturer datasheet.
The DG442DY+T is supplied in a 16-lead SOIC measuring 3.9 mm by 9.9 mm by 1.55 mm. Place the device close to the controlled signal paths and keep analog traces short to minimize parasitic capacitance and pickup. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks, and observe the stated supply sequencing and input-voltage limits before applying signals.
This product page combines package information, source-backed functional characteristics, same-footprint replacement options, comparison data, and practical PCB guidance. It helps engineers identify whether the four-channel SPST architecture matches the required signal-routing task before beginning a production design.
Pilihan pengganti yang segera untuk DG442DY+T — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
DG442DY-T1-E3
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DG442DY-T
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DG442DY-E3
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DG442DYZ
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DG442DYZ-T
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DG442DY+T Penilaian maksimum & Ciri-ciri Elektrik
| Number of Switches | 4 circuits |
| Switch Configuration | 1:1 |
| Switch Type | Single-pole single-throw (SPST) |
| On-Resistance | 85 ohm |
| Kemasan | 16-lead SOIC |
| Package Body Dimensions | 3.9 mm x 9.9 mm x 1.55 mm |
| Lead Count | 16 leads |
| Jenis Pemasangan | Surface mount |
| Digital Input Compatibility | TTL and CMOS compatible |
| Logic Threshold Reference | Internal voltage reference |
| Technology | Monolithic CMOS |
Panduan Konfigurasi Pin DG442DY+T 3.9 mm x 9.9 mm x 1.55 mm
Konfigurasi pin untuk DG442DY+T (3.9 mm x 9.9 mm x 1.55 mm pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk DG442DY+T.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
DG442DY+T patut untuk 6 aplikasis: Automated Test Equipment Signal Routing, Multimeter and Oscilloscope Input Multiplexing, Data Acquisition and Sensor Interface, Industrial Control Signal Switching, Sample-and-Hold Signal Selection, Battery-Powered Portable Instrumentation.
Automated Test Equipment Signal Routing
The DG442DY+T is suitable for automated test equipment that must route four independent analog paths under digital control. Its four SPST channels provide one 85 ohm on-resistance per path, while TTL- and CMOS-compatible control inputs allow direct connection to a tester controller, FPGA, or microcontroller. Compared with mechanical relays, the monolithic CMOS implementation avoids mechanical contact wear and supports repeated signal-path changes. The design must still account for bandwidth, charge injection, off leakage, and supply limits specified in the manufacturer datasheet. Keep routed traces short, place bypass capacitance near the device, and verify that the switched signal amplitude remains within the supported range.
Disebarkan
Multimeter and Oscilloscope Input Multiplexing
The DG442DY+T can route multiple measurement inputs in a digital multimeter, oscilloscope, or mixed-signal tester. Four independent SPST switches allow a controller to connect and disconnect separate sensor or probe paths without using a mechanical relay for every transition. The 85 ohm on-resistance is relevant when the source impedance is low enough that the added path resistance does not dominate measurement accuracy. Logic-compatible controls simplify sequencing, although relay-like behavior must be validated for high-impedance sources. Check leakage, charge injection, switching time, and off-isolation in the datasheet, and keep the analog traces compact to minimize capacitive pickup.
Disebarkan
Data Acquisition and Sensor Interface
The DG442DY+T fits data-acquisition front ends that require controlled selection among analog sensor signals. Four independent channels can connect source signals to a downstream amplifier or converter, while TTL- and CMOS-compatible inputs permit operation from common digital control logic. The 1:1 switch configuration presents a stated 85 ohm on-resistance without intentionally splitting the signal across multiple matched paths. Designers should compare that resistance with the sensor output impedance and acquisition input impedance. For high-impedance sensors, off leakage and charge injection can materially affect accuracy, so review those characteristics and use short, guarded routing in the PCB layout.
Disebarkan
Industrial Control Signal Switching
The DG442DY+T can be used in industrial control systems to switch low-bandwidth analog command or feedback signals under microcontroller supervision. Its independent SPST channels support several control points without requiring a mechanical relay, and the TTL- or CMOS-compatible inputs simplify interfacing with industrial logic. The 85 ohm on-resistance must be considered alongside actuator-driver input impedance, sensor loading, and fault-current conditions. Verify supply tolerances, logic thresholds, operating temperature, and absolute maximum ratings for the installation environment. PCB placement should minimize long analog traces and keep switching currents away from precision reference and measurement paths.
Disebarkan
Sample-and-Hold Signal Selection
The DG442DY+T is applicable to sample-and-hold and signal-selection circuits where several analog sources must be connected selectively. Four SPST switches permit independent channel control, while the monolithic CMOS implementation supports fast electronic path changes without relay bounce. The 85 ohm path resistance must be included in the acquisition network when calculating settling behavior and attenuation. Charge injection can create a voltage step when a switch changes state, and off leakage can disturb high-impedance storage capacitors, making those parameters essential selection criteria. Confirm the datasheet limits and keep the hold capacitor, switch, and subsequent buffer arranged to minimize parasitic capacitance and leakage.
Disebarkan
Battery-Powered Portable Instrumentation
The DG442DY+T can serve in portable, battery-powered instruments that switch low-frequency analog signals while avoiding the size and wear associated with mechanical relays. Four independent channels provide flexible routing in a compact 16-lead SOIC package measuring 3.9 mm by 9.9 mm by 1.55 mm. TTL- and CMOS-compatible controls allow operation across different logic systems. Before selection, calculate the effect of the 85 ohm on-resistance on source loading and review supply current, leakage, and switching behavior. Use a low-noise supply arrangement and place bypass components near the device, while keeping sensitive analog routing separate from digital control and return-current paths.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk DG442DY+T — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | DG442DY-T1-E3 | DG442DY-T | DG442DY-E3 | DG442DYZ | DG442DYZ-T |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Vishay Intertechnology | Renesas Electronics | Vishay Intertechnology | Renesas Electronics | Renesas Electronics |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Number of Circuits | 4 | 4 | 4 | 4 | 4 | 4 |
| Switch Type | Independent SPST | SPST | SPST | SPST | SPST | SPST |
| Digital Input Compatibility | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible |
Penyeberangsung Jelas
- Compact four-channel integration (vsADG713BRZ)
- Directly documented 85 ohm path resistance (vsDG442DYZ)
- No mechanical contact wear (vsDG442DY-T)
- Common digital-control compatibility (vsDG442DY-E3)
Catatan Desain
Place the DG442DY+T adjacent to the signal sources and destinations it switches. Short analog traces reduce parasitic capacitance, coupling, and input bias errors, which become more important when the source impedance is high. Use the exact pin-description table in the manufacturer datasheet when assigning tracks, preserve the package orientation, and route each switched channel away from unrelated digital clocks and switching-current return paths.
Validate the complete switched path rather than only its 85 ohm on-resistance. Check source impedance, downstream input capacitance, bandwidth, off leakage, charge injection, and off-isolation in the manufacturer datasheet. For high-impedance nodes, leakage and injected charge can be more important than DC resistance. Add a buffer near a sensitive capacitor or measurement input when the application cannot tolerate switching transients.
Use the supply voltages and logic thresholds specified in the DG441/DG442 family datasheet. TTL- and CMOS-compatible control inputs simplify interfacing, but they do not remove the need to confirm input levels, supply sequencing, and absolute maximum ratings. Place bypass capacitors close to the supply pins and keep their return paths compact so switching currents do not disturb sensitive analog references in the same board.
Do not treat a matching SOIC-16 footprint as proof of complete interchangeability. Confirm pin functions, supply range, absolute maximum ratings, switching time, on-resistance, leakage, temperature grade, and lifecycle status for every proposed replacement. Apply the exact manufacturer datasheet associated with the replacement ordering code and validate it at the system extremes before releasing production artwork.
Maklumat Kesediaan
The Analog Devices product page provides material declaration and reliability-report resources, but explicit DG442DY+T RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements were not included in the retrieved information.