DS90C363MTD - 3.3V 18-Bit LVDS FPD Transmitter | Texas Instruments
MPN: DS90C363MTD ✗ Akhir HayatDS90C363MTD Ringkasan
An LVDS transmitter is a display-interface IC that converts low-voltage digital data into balanced differential signals. In the signal-chain hierarchy, the DS90C363 belongs to interface ICs, display link controllers, and ultimately semiconductor-based display communication systems. LVDS links use differential signaling to reduce voltage noise, ground-referenced return current, and electromagnetic-interference sensitivity compared with single-ended parallel display interfaces.
The 18-bit architecture supports parallel display data while the differential link consolidates that data into fewer signal pairs. Programmable operation provides configuration flexibility for supported display timing and link arrangements. The 65 MHz operating specification, 1300 Mbps data rate, and 3.3 V supply establish the principal performance envelope of this transmitter.
The DS90C363 is associated with the DS90C363 and DS90CF364 3.3 V programmable 18-bit FPD-Link family. Its 48-pin TSSOP arrangement provides a conventional surface-mount implementation for industrial display, digital signage, test-and-measurement equipment, and embedded visualization systems where LVDS link integrity is required.
The DS90C363MTD is identified as NRND in the available cross-reference information. Designers should therefore check current Texas Instruments lifecycle, qualification, and availability notices before starting a new production design. Although inventory is reported by a distributor, lifecycle status rather than temporary stock availability should determine whether the device is appropriate for a new BOM.
For a new design requiring active lifecycle status, verify whether a related DS90C365A-family transmitter provides an appropriate supported alternative. For an existing DS90C363MTD assembly, preserve the original 48-pin TSSOP footprint, confirm the exact clocking and power-down behavior, and validate the replacement against the display timing, connector, and cable requirements.
This page consolidates the verified manufacturer description, distributor inventory and pricing, lifecycle information, and cross-reference results while explicitly identifying unavailable pin-level and electrical details. It also provides application guidance and compares the verified replacement candidates without treating unreported electrical values as guaranteed specifications.
Pilihan pengganti yang segera untuk DS90C363MTD — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera DS90C363MTD (sama faktor bentuk dan kaki) — berbeza dalam RoHS Status, Lifecycle Status, Operating Temperature Range, Package, Protocol.
DS90C363BMTX
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →DS90C365AMTX
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90C365AMT/NOPB
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90CF363MTD
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90C363MTD Spesifikasi
| Product Type | Programmable LVDS FPD-Link transmitter |
| Supply Voltage Range | 3 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| Interface Width | 18 bits |
| Frekuensi Klock Maksimum | 65 MHz |
| Maximum Data Rate | 1300 Mbps |
| LVDS Output Voltage | 0.45 V |
| Number of LVDS Drivers | 3 drivers |
| Protocol | FPD-Link |
| Kemasan | 48-TSSOP, 0.240 inch (6.10 mm) width |
| Jenis Pemasangan | Surface mount |
| Gambaran Suhu Operasi | -10 C to +70 C |
| Supply Packaging | Tube |
| Status Lingkungan Hidup | Not Recommended for New Designs (NRND) |
| Reported Distributor Inventory | 96,780 pieces |
| Status RoHS | Non-compliant |
Panduan Konfigurasi Pin DS90C363MTD 48-tssop, 0.240 inch (6.10 mm) width
Konfigurasi pin untuk DS90C363MTD (48-tssop, 0.240 inch (6.10 mm) width pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk DS90C363MTD.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
DS90C363MTD patut untuk 6 aplikasis: Industrial Flat-Panel Display Interface, Digital Signage Controller, Test and Measurement Instrumentation, Embedded Human-Machine Interface, Medical Display Controller, Point-of-Sale Terminal Display.
Industrial Flat-Panel Display Interface
The DS90C363MTD fits an 18-bit LVDS display link that must operate from a 3 V to 3.6 V supply at up to 65 MHz. Its three LVDS drivers and up to 1300 Mbps throughput provide a defined path for transferring display information from a controller or processor to an LVDS panel. The 48-pin TSSOP package supports conventional surface-mount assembly. Because the device is NRND and has a reported -10 C to +70 C range, new industrial products should verify temperature requirements and consider a currently supported family member, while the original part remains useful for maintenance of qualified equipment.
Disebarkan
Digital Signage Controller
The DS90C363MTD can carry parallel display data from a digital-signage controller to an LVDS panel while reducing susceptibility to common-mode noise through differential signaling. Its 18-bit interface, 65 MHz maximum clock frequency, and three-driver arrangement align with multi-lane flat-panel links used in larger commercial displays. The design must account for the original device's NRND lifecycle, so operators should preserve traceability and qualify any replacement. Cable length, connector pinout, and display timing should be validated together because those details are not fully published in the supplied source data.
Disebarkan
Test and Measurement Instrumentation
The DS90C363MTD is applicable when an instrument needs to bridge a controller to an 18-bit LVDS display without using a long single-ended parallel bus. Differential transmission reduces sensitivity to ground offsets and radiated noise, while the device's 3.3 V operating class and 65 MHz capability fit embedded display subsystems. Bench instruments often have long internal cable runs, making controlled LVDS routing and connector compatibility important. The transmitter's NRND status should be checked against the instrument's production horizon; use the original part for unchanged legacy products or move new designs to a supported, verified replacement.
Disebarkan
Embedded Human-Machine Interface
An embedded human-machine interface can use the DS90C363MTD when its controller drives an 18-bit LVDS panel at up to 65 MHz. The three LVDS outputs reduce the number of high-speed single-ended traces and can improve signal integrity in compact systems, although board-space demands remain significant because the device uses a 48-pin TSSOP. The 3 V to 3.6 V supply range fits 3.3 V logic systems, but the reported -10 C to +70 C operating range must be checked against enclosure conditions. For new safety- or temperature-sensitive products, validate an active alternative and review the exact power and timing requirements.
Disebarkan
Medical Display Controller
The DS90C363MTD may support a medical monitoring or diagnostic display requiring an 18-bit differential link. Differential signaling can help reduce coupling from nearby digital and power circuitry, while 65 MHz operation provides the stated basis for the reported 1300 Mbps throughput. However, medical systems commonly require extended lifecycle planning and controlled component changes, making the NRND status especially significant. Use the original DS90C363MTD only where an unchanged qualified design exists; otherwise, evaluate a supported transmitter and complete electrical, EMC, and product-risk validation before substitution.
Disebarkan
Point-of-Sale Terminal Display
The DS90C363MTD fits a point-of-sale terminal that transfers 18-bit display data to a compact LVDS panel at up to 65 MHz. Differential outputs are useful inside a crowded terminal where display routing may pass near switching supplies and processor circuitry. The three-driver arrangement and 48-pin TSSOP package permit integration without a high-speed parallel connector, although PCB layout still requires controlled impedance and careful return-path continuity. Because the component is NRND, a service-focused product can retain the original part, whereas a new terminal platform should start with a lifecycle-supported alternative and verified timing comparison.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk DS90C363MTD — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | DS90C363BMT | DS90C365AMTX | DS90C365AMT/NOPB | DS90CF363MTD |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 48-TSSOP | 48-TSSOP | 48-TSSOP | 48-TSSOP | 48-TSSOP |
| Product Type | 18-bit programmable LVDS FPD-Link transmitter | LVDS interface transmitter | DS90C365A LVDS transmitter | DS90C365A LVDS transmitter | LVDS FPD-Link transmitter |
Penyeberangsung Jelas
- Direct 18-bit FPD-Link integration at a 65 MHz clock (vsDS90CF363MTD)
- Established 3.3 V supply range (vsDS90C365AMTX)
- Published 1300 Mbps throughput (vsDS90C363BMT)
Catatan Desain
Route the differential LVDS pairs as tightly coupled traces with continuous reference planes and matched lengths. Avoid splitting the ground or power plane beneath a pair, and place the transceiver close to the display connector or FPD interface. The supplied data confirms three drivers and a 48-pin TSSOP package but does not provide the exact pin map, so final routing must be based on the current manufacturer pin configuration rather than assumptions.
Validate LVDS amplitude, differential voltage, timing, and propagation delay with the display sink and the intended cable or PCB interconnect. The DS90C363MTD is specified for up to 65 MHz and the comparison data reports a 0.45 V output, while a candidate family member shows 0.2 V. Substitution therefore requires measurement at the receiver rather than reliance on connector compatibility or package equality alone.
Do not assume that every 48-pin TSSOP FPD-Link transmitter is electrically interchangeable. The DS90C365A is documented as pin-to-pin compatible and improved, but shutdown timing, input mapping, data format, and supply sequencing must still be checked. The DS90C363MTD is NRND, so distinguish a like-for-like maintenance substitution from a new-design migration and preserve the original approved part number in manufacturing records.
Use the manufacturer's recommended supply decoupling and provide clean 3.3 V power to the transmitter because display data corruption can result from both insufficient supply integrity and poor LVDS signal quality. The supplied data confirms a 3 V to 3.6 V operating range but does not provide current consumption, quiescent current, or capacitor recommendations. Those values must be obtained from the current datasheet before sizing the supply and placement of local bypass components.
Maklumat Kesediaan
The supplied comparison data lists the DS90C363MTD with RoHS Code No. Separate NOPB ordering variants may have different environmental documentation, but their records were not supplied. REACH, lead-free, halogen-free, and conflict-minerals status are therefore unknown.
