DS90CR288AMTDX - 85 MHz 28-Bit LVDS Receiver | Texas Instruments
MPN: DS90CR288AMTDX ✗ Akhir HayatDS90CR288AMTDX Ringkasan
A Channel Link serializer or transmitter converts parallel logic data into low-voltage differential signaling for reliable transfer across cables, backplanes, and circuit-board interconnects. An LVDS interface receiver reverses that process by detecting the differential voltage on each pair and reconstructing the corresponding digital bit stream. The DS90CR288AMTDX therefore belongs to the interface-IC hierarchy: LVDS receiver, high-speed interface IC, data converter, and semiconductor.
Principal features include an 85 MHz maximum clock rate, four differential data inputs handling 28 bits per transfer, a rising-edge data-strobe architecture, and a +3.3 V supply. The device accepts shift clocks from 20 MHz through 85 MHz while maintaining a 50% duty cycle on the receiver output clock. Its 56-pin TSSOP package provides a standardized surface-mount footprint for high-speed interface designs.
The differential signaling architecture reduces sensitivity to common-mode noise compared with single-ended interconnects. This makes the receiver appropriate for point-to-point links where data must cross a connector, cable, or noisy backplane region. The parallel output side converts the recovered data into logic-level signals for a controller, display, video pipeline, or data-capture system.
Typical applications include industrial control links, video and imaging data transport, test-and-measurement equipment, instrumentation, and embedded systems that use the National Semiconductor Channel Link interface. It is normally paired with a compatible DS90CR287-family transmitter, with the link topology and support circuitry determined from the manufacturer datasheet.
Layout is critical because the receiver must process small differential signals at clock rates as high as 85 MHz. Place the device close to the connector or cable termination, maintain symmetric routing between differential pairs, and provide the bypass capacitance specified by the manufacturer. Keep return-path current continuous and avoid routing data strobe signals across the differential inputs.
This page consolidates interface specifications, lifecycle information, verified cross-references, and practical replacement guidance. It is intended to help engineers identify the correct receiver variant, evaluate equivalent parts, and plan a pin-compatible redesign without overlooking signal-integrity or board-layout constraints.
Pilihan pengganti yang segera untuk DS90CR288AMTDX — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
DS90CR288AMTDX/NOPB
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90CR288MTDX/NOPB
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90CR288AMTD
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90CR288AMTDX Spesifikasi
| Product Type | LVDS Channel Link receiver |
| Tegangan Pemberi Arus | +3.3 V |
| Frekuensi Klock Maksimum | 85 MHz |
| Minimum Shift Clock Frequency | 20 MHz |
| Data Width | 28 bits |
| Differential Data Inputs | 4 LVDS data streams |
| Output Signal Type | LVCMOS/LVTTL |
| Clock Edge | Rising edge |
| Receiver Output Clock Duty Cycle | 50% |
| Kemasan | 56-pin TSSOP |
| Jenis Pemasangan | Surface mount |
| Status Lingkungan Hidup | NRND |
Panduan Konfigurasi Pin DS90CR288AMTDX 56-pin tssop
Konfigurasi pin untuk DS90CR288AMTDX (56-pin tssop pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk DS90CR288AMTDX.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
DS90CR288AMTDX patut untuk 6 aplikasis: Industrial Control Data Links, Video and Imaging Data Transport, Test and Measurement Instrumentation, Embedded System Backplane Communication, Imaging Sensor Data Acquisition, Telecommunications and Network Equipment.
Industrial Control Data Links
The DS90CR288AMTDX fits industrial control systems that transfer a 28-bit parallel payload across a noisy cable or backplane connection. Its four LVDS inputs support the Channel Link architecture, while the 20 MHz to 85 MHz shift-clock range accommodates moderately high-rate control and status traffic. Differential signaling improves noise immunity over single-ended interconnects. Place the receiver close to the connector, route each LVDS pair symmetrically, and confirm the transmitter, clock topology, and termination arrangement against the manufacturer guidance.
Disebarkan
Video and Imaging Data Transport
The DS90CR288AMTDX can receive 28 bits of parallel data from a compatible Channel Link transmitter in video and imaging equipment. Its 85 MHz maximum shift-clock rate and four differential data inputs provide a consolidated path for pixel or control data. The receiver converts LVDS information into LVCMOS or LVTTL outputs for the downstream display pipeline. Keep the differential pairs short and matched, preserve a continuous ground reference, and isolate the recovered clock from noisy switching nodes to maintain data integrity.
Disebarkan
Test and Measurement Instrumentation
The DS90CR288AMTDX is appropriate for laboratory and industrial instrumentation that moves a parallel data group between circuit cards through LVDS. The 28-bit Channel Link format reduces the number of signal conductors compared with a fully single-ended implementation, while its rising-edge data-strobe architecture supports deterministic sampling. At clock rates as high as 85 MHz, connector and return-path design remain important. Use the manufacturer pin-description and layout guidance to separate the clock, data pairs, and supply returns.
Disebarkan
Embedded System Backplane Communication
The DS90CR288AMTDX can serve as the receiving endpoint for a compact backplane link in embedded equipment requiring more data width than a conventional low-speed serial interface. Four LVDS pairs carry a 28-bit payload, and the supported 20 MHz to 85 MHz clock range suits moderate-speed control and sensor-data aggregation. Differential routing reduces susceptibility to crosstalk and common-mode noise. Validate the cable length, transmitter clock, receiver termination, and output timing over the complete temperature range before production release.
Disebarkan
Imaging Sensor Data Acquisition
Imaging systems can use the DS90CR288AMTDX to receive a 28-bit data word group from a compatible transmitter when the interface uses LVDS Channel Link signaling. The receiver supports an 85 MHz shift clock and produces parallel logic outputs for capture or processing logic. At this rate, connector pins, cable geometry, and PCB return paths influence signal quality. Keep clock routing away from data inputs and use the manufacturer pin table to preserve the defined channel and clock assignments.
Disebarkan
Telecommunications and Network Equipment
The DS90CR288AMTDX is suitable for line-card or interface-module designs that use the established Channel Link architecture between circuit boards. Its 28-bit parallel width consolidates multiple control or payload signals into four differential lanes, while the 56-pin TSSOP package supports compact surface-mount assemblies. Because the device is identified as NRND, long-lived network programs should confirm availability early and qualify the selected ordering designation. Verify inter-board cable length and ground-reference continuity with system-level testing.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk DS90CR288AMTDX — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | DS90CR288AMTDX/NOPB | DS90CR288MTDX/NOPB | DS90CR288AMTD |
|---|---|---|---|---|
| Package | 56-TSSOP | 56-TSSOP - same | 56-TSSOP - same | 56-TSSOP - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | 28-bit LVDS Channel Link receiver | 28-bit LVDS Channel Link receiver | 28-bit LVDS Channel Link receiver | 28-bit LVDS Channel Link receiver |
| Supply Voltage | +3.3 V | +3.3 V | +3.3 V | +3.3 V |
| Data Width | 28 bits | 28 bits | 28 bits | 28 bits |
Penyeberangsung Jelas
- Closest lead-free ordering option (vsDS90CR288AMTDX/NOPB)
- Same-family receiver with matching package (vsDS90CR288MTDX/NOPB)
- Established ordering designation in the same family (vsDS90CR288AMTD)
Catatan Desain
Route the four LVDS data pairs as short, symmetric differential connections between the transmitter, connector, and receiver. Maintain a continuous ground or return reference beneath the link and avoid splitting the reference plane beneath the differential pair. Keep the receiver close to the connector or cable termination so that connector and cable losses occur ahead of the active input stage.
Separate the recovered clock and data-strobe nets from the LVDS inputs, especially when operating near the 85 MHz maximum. Avoid crossing strobe traces beneath differential pairs, and do not route high-current switching nodes near the receiver. Use the manufacturer clock topology and test the assembled channel with a low-noise, high-bandwidth method to verify eye margin across voltage and temperature.
Do not treat DS90CR288AMTDX, DS90CR288AMTDX/NOPB, DS90CR288MTDX/NOPB, and DS90CR288AMTD as automatically interchangeable order codes. Although they share the DS90CR288 family and 56-pin TSSOP format, compare supply pins, clock inputs, output assignments, no-connect pins, and ordering information in the manufacturer datasheet. Verify a new assembly with the intended transmitter and representative interconnect.
Maklumat Kesediaan
The NOPB ordering designation identifies a lead-free finish, but separate RoHS, REACH, halogen-free, and conflict-minerals declarations are not stated in the available manufacturer and distributor records.