Texas Instruments

DS90CR288AMTDX - 85 MHz 28-Bit LVDS Receiver | Texas Instruments

부품 번호: DS90CR288AMTDX ✗ 단종
+3.3 V Vdss 56-pin TSSOP Package 85 MHz Speed
MOQ: 1 |

DS90CR288AMTDX 개요

The Texas Instruments DS90CR288AMTDX is a +3.3 V rising-edge data-strobe LVDS receiver for a 28-bit Channel Link interface, operating up to 85 MHz in a 56-pin TSSOP package. The receiver supports 20 MHz to 85 MHz shift-clock operation and provides a 50% duty-cycle receiver output clock. It is designed to deserialize four LVDS data streams carrying 28 bits of parallel data into an LVCMOS or LVTTL output bus.

A Channel Link serializer or transmitter converts parallel logic data into low-voltage differential signaling for reliable transfer across cables, backplanes, and circuit-board interconnects. An LVDS interface receiver reverses that process by detecting the differential voltage on each pair and reconstructing the corresponding digital bit stream. The DS90CR288AMTDX therefore belongs to the interface-IC hierarchy: LVDS receiver, high-speed interface IC, data converter, and semiconductor.

Principal features include an 85 MHz maximum clock rate, four differential data inputs handling 28 bits per transfer, a rising-edge data-strobe architecture, and a +3.3 V supply. The device accepts shift clocks from 20 MHz through 85 MHz while maintaining a 50% duty cycle on the receiver output clock. Its 56-pin TSSOP package provides a standardized surface-mount footprint for high-speed interface designs.

The differential signaling architecture reduces sensitivity to common-mode noise compared with single-ended interconnects. This makes the receiver appropriate for point-to-point links where data must cross a connector, cable, or noisy backplane region. The parallel output side converts the recovered data into logic-level signals for a controller, display, video pipeline, or data-capture system.

Typical applications include industrial control links, video and imaging data transport, test-and-measurement equipment, instrumentation, and embedded systems that use the National Semiconductor Channel Link interface. It is normally paired with a compatible DS90CR287-family transmitter, with the link topology and support circuitry determined from the manufacturer datasheet.

Layout is critical because the receiver must process small differential signals at clock rates as high as 85 MHz. Place the device close to the connector or cable termination, maintain symmetric routing between differential pairs, and provide the bypass capacitance specified by the manufacturer. Keep return-path current continuous and avoid routing data strobe signals across the differential inputs.

This page consolidates interface specifications, lifecycle information, verified cross-references, and practical replacement guidance. It is intended to help engineers identify the correct receiver variant, evaluate equivalent parts, and plan a pin-compatible redesign without overlooking signal-integrity or board-layout constraints.

드롭인 대체품: DS90CR288AMTDX — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

DS90CR288AMTDX/NOPB

✅ 드롭인
📦 56-TSSOP
Lead-free NOPB ordering designation; retains +3.3 V supply, 28-bit width, 85 MHz rating, and 56-pin TSSOP interface with 0% key-parameter difference

📋 참조 대체품 (카탈로그에 없음)

DS90CR288MTDX/NOPB

✅ 드롭인
📦 56-TSSOP
Related DS90CR288 ordering designation in the same 56-pin TSSOP family; key clock and data parameters require confirmation against the DS90CR288A datasheet

📋 참조 대체품 (카탈로그에 없음)

DS90CR288AMTD

✅ 드롭인
📦 56-TSSOP
Earlier ordering designation of the same DS90CR288 receiver family with matching 56-pin TSSOP interface; procurement status differs from the X and NOPB variants

📋 참조 대체품 (카탈로그에 없음)

DS90CR288AMTDX 사양

Product Type LVDS Channel Link receiver
공급 전압 +3.3 V
최대 클록 주파수 85 MHz
Minimum Shift Clock Frequency 20 MHz
Data Width 28 bits
Differential Data Inputs 4 LVDS data streams
Output Signal Type LVCMOS/LVTTL
Clock Edge Rising edge
Receiver Output Clock Duty Cycle 50%
패키지 56-pin TSSOP
실장 유형 Surface mount
수명 주기 상태 NRND

DS90CR288AMTDX 56-pin tssop 핀 구성 가이드

DS90CR288AMTDX(56-pin tssop 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

DS90CR288AMTDX의 56-pin tssop 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: DS90CR288AMTDX.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

DS90CR288AMTDX 적합 용도: 6 애플리케이션s: Industrial Control Data Links, Video and Imaging Data Transport, Test and Measurement Instrumentation, Embedded System Backplane Communication, Imaging Sensor Data Acquisition, Telecommunications and Network Equipment.

🏭

Industrial Control Data Links

The DS90CR288AMTDX fits industrial control systems that transfer a 28-bit parallel payload across a noisy cable or backplane connection. Its four LVDS inputs support the Channel Link architecture, while the 20 MHz to 85 MHz shift-clock range accommodates moderately high-rate control and status traffic. Differential signaling improves noise immunity over single-ended interconnects. Place the receiver close to the connector, route each LVDS pair symmetrically, and confirm the transmitter, clock topology, and termination arrangement against the manufacturer guidance.

📺

Video and Imaging Data Transport

The DS90CR288AMTDX can receive 28 bits of parallel data from a compatible Channel Link transmitter in video and imaging equipment. Its 85 MHz maximum shift-clock rate and four differential data inputs provide a consolidated path for pixel or control data. The receiver converts LVDS information into LVCMOS or LVTTL outputs for the downstream display pipeline. Keep the differential pairs short and matched, preserve a continuous ground reference, and isolate the recovered clock from noisy switching nodes to maintain data integrity.

🔧

Test and Measurement Instrumentation

The DS90CR288AMTDX is appropriate for laboratory and industrial instrumentation that moves a parallel data group between circuit cards through LVDS. The 28-bit Channel Link format reduces the number of signal conductors compared with a fully single-ended implementation, while its rising-edge data-strobe architecture supports deterministic sampling. At clock rates as high as 85 MHz, connector and return-path design remain important. Use the manufacturer pin-description and layout guidance to separate the clock, data pairs, and supply returns.

🖥️

Embedded System Backplane Communication

The DS90CR288AMTDX can serve as the receiving endpoint for a compact backplane link in embedded equipment requiring more data width than a conventional low-speed serial interface. Four LVDS pairs carry a 28-bit payload, and the supported 20 MHz to 85 MHz clock range suits moderate-speed control and sensor-data aggregation. Differential routing reduces susceptibility to crosstalk and common-mode noise. Validate the cable length, transmitter clock, receiver termination, and output timing over the complete temperature range before production release.

🎥

Imaging Sensor Data Acquisition

Imaging systems can use the DS90CR288AMTDX to receive a 28-bit data word group from a compatible transmitter when the interface uses LVDS Channel Link signaling. The receiver supports an 85 MHz shift clock and produces parallel logic outputs for capture or processing logic. At this rate, connector pins, cable geometry, and PCB return paths influence signal quality. Keep clock routing away from data inputs and use the manufacturer pin table to preserve the defined channel and clock assignments.

🌐

Telecommunications and Network Equipment

The DS90CR288AMTDX is suitable for line-card or interface-module designs that use the established Channel Link architecture between circuit boards. Its 28-bit parallel width consolidates multiple control or payload signals into four differential lanes, while the 56-pin TSSOP package supports compact surface-mount assemblies. Because the device is identified as NRND, long-lived network programs should confirm availability early and qualify the selected ordering designation. Verify inter-board cable length and ground-reference continuity with system-level testing.

추천 제품 요약

DS90CR287 Compatible Channel Link transmitter 사용처: Industrial Control Data Links, Video and Imaging Data Transport, Test and Measurement Instrumentation, Embedded System Backplane Communication, Imaging Sensor Data Acquisition, Telecommunications and Network Equipment DS90CR288MTDX/NOPB Related receiver option 사용처: Industrial Control Data Links, Embedded System Backplane Communication DS90CR288AMTDX/NOPB Lead-family receiver alternative 사용처: Video and Imaging Data Transport, Imaging Sensor Data Acquisition DS90CR288AMTD Same-family receiver option 사용처: Test and Measurement Instrumentation, Telecommunications and Network Equipment
What is the DS90CR288AMTDX?
The DS90CR288AMTDX is a +3.3 V, 28-bit Channel Link receiver from Texas Instruments. It receives four LVDS data streams, reconstructs 28 bits of parallel data, and supports a rising-edge data-strobe architecture. According to the manufacturer product page for DS90CR288A, the device is a 28-bit Channel Link receiver rated for operation up to 85 MHz.
What clock frequencies does DS90CR288AMTDX support?
The DS90CR288AMTDX supports shift-clock operation from 20 MHz to 85 MHz. The maximum operating clock is 85 MHz, and the receiver output clock has a 50% duty cycle. The DS90CR288A datasheet describes the 20 MHz to 85 MHz shift-clock range and 50% receiver-output duty-cycle characteristics for this family.
Where can I download the DS90CR288AMTDX datasheet PDF?
The manufacturer datasheet is available through the Texas Instruments DS90CR288A product page at https://www.ti.com/product/DS90CR288A. That page provides the primary electrical characteristics, ordering information, pin descriptions, and application guidance. Use the pin-description table and recommended-layout section in that datasheet when assigning tracks and planning decoupling.
Where can I find the DS90CR288AMTDX pinout?
The DS90CR288AMTDX uses a 56-pin TSSOP package, and its complete pin assignment is documented in the DS90CR288A manufacturer datasheet. Use the package pin-description table to identify the four differential data pairs, clock inputs, supply pins, and ground pins. Keep the LVDS pair assignments unchanged when adapting an existing board.
Is DS90CR288AMTDX the same as DS90CR288AMTDX/NOPB?
DS90CR288AMTDX/NOPB is the lead-free ordering designation of the same DS90CR288A receiver family and is identified as a complete replacement for the original part in cross-reference listings. Both use the 56-pin TSSOP format and the same +3.3 V, 28-bit, 85 MHz receiver architecture. Confirm the ordering suffix required by the manufacturer before releasing a new production BOM.
What is the best drop-in replacement for DS90CR288AMTDX?
DS90CR288AMTDX/NOPB is the closest documented drop-in replacement for DS90CR288AMTDX because it retains the same 56-pin TSSOP interface, +3.3 V supply, 28-bit data width, and 85 MHz receiver rating. Cross-reference results also identify DS90CR288MTDX/NOPB as a functionally equivalent option, but verify every pin function and timing parameter against the manufacturer datasheet before substitution.
Can DS90CR288MTDX/NOPB replace DS90CR288AMTDX?
DS90CR288MTDX/NOPB can serve as a candidate replacement because cross-reference listings describe consistent terminals, packages, and principal functional characteristics. It uses the same 56-pin TSSOP format and belongs to the same DS90CR288 receiver family. The substitution must still pass signal-integrity, timing, and system-level channel-link verification on the target board.
DS90CR288AMTDX vs DS90CR288AMTDX/NOPB: which one should I buy?
DS90CR288AMTDX/NOPB is the preferred production choice when the manufacturer confirms that the NOPB lead-free designation is required for current procurement. It retains the same receiver architecture, 56-pin TSSOP package, 28-bit width, and 85 MHz maximum clock as DS90CR288AMTDX. Use the Request a Quote form on this page to request availability and lead-time confirmation.
When should I choose DS90CR288AMTDX over another LVDS receiver?
Choose DS90CR288AMTDX when the design specifically requires a 28-bit Channel Link receiver, four differential data inputs, a rising-edge data strobe, and operation up to 85 MHz in a 56-pin TSSOP package. A generic LVDS receiver may have fewer data lanes or a different clock architecture and therefore cannot be assumed to be pin-compatible.
Is DS90CR288AMTDX suitable for video and imaging systems?
The DS90CR288AMTDX is suitable for systems that use the National Semiconductor Channel Link architecture to move 28-bit parallel data over LVDS pairs. Video and imaging designs can use it when the transmitter, receiver clocking, connector pinout, and cable length match the family specifications. Differential routing and connector return-path design remain essential at the supported clock rate.
What is the difference between LVDS and LVCMOS output signaling?
LVDS carries information as a small differential voltage between paired conductors, while LVCMOS is a single-ended, ground-referenced logic interface. The DS90CR288AMTDX receives LVDS data and presents LVCMOS or LVTTL parallel outputs to the receiving logic system. This division allows a link to retain noise immunity across an interconnect while presenting a conventional parallel bus internally.
What can replace DS90CR288AMTDX?
The closest documented replacements are DS90CR288AMTDX/NOPB and DS90CR288MTDX/NOPB from the same manufacturer family. Both are identified as candidates with matching 56-pin TSSOP packaging and closely related Channel Link characteristics. Use the pin-description and timing tables in the DS90CR288A datasheet to confirm compatibility before changing a production design.
Is DS90CR288AMTDX the same as DS90CR288MTDX/NOPB?
DS90CR288MTDX/NOPB is not merely a different label for DS90CR288AMTDX; it is a distinct ordering designation within the related DS90CR288 family. Cross-reference listings describe matching package and terminal characteristics, but engineers should still compare power, clock, output, and no-connect assignments in the manufacturer documentation. Board qualification remains required.
Where can I buy DS90CR288AMTDX?
Use the Request a Quote form on this page to request DS90CR288AMTDX pricing, stock confirmation, and lead-time information from XAIPART. Because the manufacturer lists this family as NRND, allocation status can vary with remaining inventory. Provide the required package, quantity, and target date so the quote can reflect the correct ordering configuration.
What is the lead time for DS90CR288AMTDX?
The current lead time for DS90CR288AMTDX is not published as a fixed value and should be confirmed through the Request a Quote form on this page. The part is listed as NRND, so supply depends on remaining factory and distribution inventory rather than a broad active-production schedule. Include your required quantity and production window when requesting the quote.
Is DS90CR288AMTDX currently in stock?
Stock for DS90CR288AMTDX should be confirmed through the Request a Quote form on this page rather than assumed from the existence of a catalog listing. The Mouser product record identifies the device as NRND, which means new availability can be limited. Submit the required quantity and target date to obtain a current allocation response.
What are the key specifications of DS90CR288AMTDX that engineers should know?
The DS90CR288AMTDX is a +3.3 V, 28-bit LVDS Channel Link receiver with four differential data streams, a rising-edge data strobe, 20 MHz to 85 MHz shift-clock support, and a 50% receiver-output duty cycle. It is packaged in a 56-pin TSSOP and is identified by Mouser as NRND. These details define the key constraints for interface, layout, and lifecycle planning.
Which Texas Instruments transmitter pairs with DS90CR288AMTDX?
The DS90CR287 family is the matching National Semiconductor Channel Link transmitter for the DS90CR288 receiver, using four LVDS data pairs and a related clock architecture. The DS90CR287 converts 28-bit parallel data into four LVDS streams for transmission to the receiver. Confirm voltage, timing, and pin compatibility with the manufacturer application information.

엔지니어링 참조 데이터: DS90CR288AMTDX — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose DS90CR288AMTDX when the design already uses a DS90CR288A 28-bit Channel Link receiver and the present ordering designation remains available. DS90CR288AMTDX/NOPB is the closest lead-family alternative when procurement requires the NOPB designation; it retains the same 3.3 V supply, 28-bit width, 85 MHz clock rating, and 56-pin TSSOP footprint. Consider DS90CR288MTDX/NOPB when the related family ordering is preferable, but check its detailed clock, pin, and timing information against the DS90CR288A datasheet before release. DS90CR288AMTD provides another same-family option for existing boards. Because all candidates are from the same specialized interface family and the device is NRND, confirm lifecycle, availability, and long-term supply through the Request a Quote form rather than assuming that a generic LVDS receiver is drop-in compatible.

대체품과의 비교

파라미터 이 제품 DS90CR288AMTDX/NOPB DS90CR288MTDX/NOPB DS90CR288AMTD
Package 56-TSSOP 56-TSSOP - same 56-TSSOP - same 56-TSSOP - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Product Type 28-bit LVDS Channel Link receiver 28-bit LVDS Channel Link receiver 28-bit LVDS Channel Link receiver 28-bit LVDS Channel Link receiver
Supply Voltage +3.3 V +3.3 V +3.3 V +3.3 V
Data Width 28 bits 28 bits 28 bits 28 bits

주요 차별점

  • Closest lead-free ordering option (vs DS90CR288AMTDX/NOPB)
  • Same-family receiver with matching package (vs DS90CR288MTDX/NOPB)
  • Established ordering designation in the same family (vs DS90CR288AMTD)

설계 노트

Route the four LVDS data pairs as short, symmetric differential connections between the transmitter, connector, and receiver. Maintain a continuous ground or return reference beneath the link and avoid splitting the reference plane beneath the differential pair. Keep the receiver close to the connector or cable termination so that connector and cable losses occur ahead of the active input stage.

Separate the recovered clock and data-strobe nets from the LVDS inputs, especially when operating near the 85 MHz maximum. Avoid crossing strobe traces beneath differential pairs, and do not route high-current switching nodes near the receiver. Use the manufacturer clock topology and test the assembled channel with a low-noise, high-bandwidth method to verify eye margin across voltage and temperature.

Do not treat DS90CR288AMTDX, DS90CR288AMTDX/NOPB, DS90CR288MTDX/NOPB, and DS90CR288AMTD as automatically interchangeable order codes. Although they share the DS90CR288 family and 56-pin TSSOP format, compare supply pins, clock inputs, output assignments, no-connect pins, and ordering information in the manufacturer datasheet. Verify a new assembly with the intended transmitter and representative interconnect.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The NOPB ordering designation identifies a lead-free finish, but separate RoHS, REACH, halogen-free, and conflict-minerals declarations are not stated in the available manufacturer and distributor records.

데이터 검증일: 2026-11-16 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

DS90CR288AMTDX DS90CR288AMTDX nopb DS90CR288AMTDX datasheet DS90CR288AMTDX pinout DS90CR288AMTDX datasheet pdf DS90CR288AMTDX equivalent DS90CR288AMTDX replacement DS90CR288AMTDX vs DS90CR288AMTDX/NOPB DS90CR288AMTDX price DS90CR288AMTDX stock Texas Instruments DS90CR288AMTDX DS90CR288A 28-bit LVDS receiver DS90CR288AMTDX 56 TSSOP DS90CR288AMTDX Channel Link application

관련 부품 & 용어

Texas Instruments DS90CR288AMTDX DS90CR288A DS90CR288AMTDX/NOPB DS90CR288MTDX/NOPB DS90CR288AMTD DS90CR287 LVDS LVCMOS LVTTL Channel Link high-speed interface IC data converter receiver 28-bit data width 85 MHz clock rising-edge data strobe 56-pin TSSOP surface mount differential signaling industrial control video data transport test and measurement NRND lifecycle status RoHS REACH
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기