DSPIC33EP256MC502T-E/SO - 16-bit DSC 70 MIPS Motor Control | Microchip
MPN: DSPIC33EP256MC502T-E/SO ✓ AktifDSPIC33EP256MC502T-E/SO Ringkasan
A digital signal controller combines the computational capability of a microcontroller with the arithmetic throughput of a digital signal processor. Within the power management hierarchy of embedded systems, a DSC sits above basic MCUs and is purpose-built for closed-loop control tasks such as field-oriented control (FOC) of motors, where fast multiply-accumulate operations and deterministic interrupt latency are essential.
Key features of this device include the 70 MIPS dsPIC DSC core with integrated DSP engine, 256 KB Flash, on-chip MCPWM (motor control PWM) peripherals, quadrature encoder interface (QEI), a CAN module for industrial networking, two integrated operational amplifiers, and three analog comparators. These analog and timing peripherals reduce external component count in power conversion and motor drive designs.
Architecturally, the dsPIC33EP family pairs the 16-bit CPU with pipelined DSP instructions, single-cycle MAC, and hardware division support, enabling real-time current loops at tens of kilohertz. The E temperature grade variant (-40C to +125C) extends operation into harsh industrial and automotive-adjacent environments where standard 0C to +70C parts cannot be used.
Typical applications include brushless DC (BLDC) and permanent magnet synchronous motor (PMSM) control, power factor correction stages, digital power supplies, and industrial automation nodes using CAN. The integrated op amps and comparators directly support current-sense signal chains common in inverter designs.
When designing with this part, budget Flash and pin resources carefully: the 28-pin package multiplexes MCPWM, QEI, CAN, and UART functions on shared pins, so verify pin mapping early with Microchip's pin manager tooling.
This page synthesizes verified distributor data, drop-in alternatives within the dsPIC33EP256MC502 family, pricing tiers, and practical design guidance not consolidated in the manufacturer datasheet.
Pilihan pengganti yang segera untuk DSPIC33EP256MC502T-E/SO — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera DSPIC33EP256MC502T-E/SO (sama faktor bentuk dan kaki) — berbeza dalam Package, Core Architecture, Operating Temperature, Communication Interfaces, Flash Program Memory.
DSPIC33EP256MC502T-I/SO
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →DSPIC33EP256MC502-H/SO
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →DSPIC33EP256MC502-I/SO
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DSPIC33EP128MC502-I/SO
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →DSPIC33EP64MC502-I/SO
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
DSPIC33EP256MC502T-E/SO Penilaian maksimum & Ciri-ciri Elektrik
| Core Architecture | 16-bit dsPIC DSC |
| Max CPU Speed | 70 MIPS (60 MHz) |
| Flash Program Memory | 256 KB |
| SRAM | 32 KB |
| Kemasan | 28-pin SOIC (SO) |
| Suhu Operasi | -40C to +125C (E grade) |
| Motor Control PWM (MCPWM) | Yes |
| Quadrature Encoder Interface (QEI) | Yes |
| CAN Module | Yes |
| Integrated Op Amps | 2 |
| Analog Comparators | 3 |
| Integrated DSP Engine | Yes |
| Jenis Pemasangan | Surface Mount |
| Packaging | Tape & Reel (T suffix) |
Panduan Konfigurasi Pin DSPIC33EP256MC502T-E/SO 28-pin soic (so)
Konfigurasi pin untuk DSPIC33EP256MC502T-E/SO (28-pin soic (so) pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk DSPIC33EP256MC502T-E/SO.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
DSPIC33EP256MC502T-E/SO patut untuk 6 aplikasis: BLDC Motor Control, PMSM Field-Oriented Control, Digital Power Supplies and PFC, Industrial CAN Networking Nodes, Automotive-Adjacent and Harsh Environment Systems, Embedded Sensing with On-Chip Analog.
BLDC Motor Control
The DSPIC33EP256MC502T-E/SO fits brushless DC motor control because its 70 MIPS dsPIC33E core executes commutation and current-loop algorithms well above typical electrical frequencies of BLDC machines. The integrated MCPWM peripheral generates complementary or independent PWM channels with hardware dead time, eliminating external gate-timing logic, while the quadrature encoder interface reads position feedback directly. The two on-chip op amps buffer shunt-current signals and the three comparators implement cycle-by-cycle over-current protection. In a 28-pin SOIC, this consolidation removes external amplifiers and comparator ICs, cutting BOM cost and board area. The extended -40C to +125C rating suits drives inside sealed enclosures where ambient heat accumulates.
Disebarkan
PMSM Field-Oriented Control
For permanent magnet synchronous motor drives using field-oriented control, the DSPIC33EP256MC502T-E/SO provides the single-cycle multiply-accumulate DSP engine needed for Clarke/Park transforms and PI current regulators at 10-20 kHz loop rates. The 256 KB Flash accommodates sensorless observers such as sliding-mode or flux-linkage estimation plus a CAN stack, leaving headroom for field upgrades. The MCPWM module's complementary outputs drive three-phase inverters through gate drivers, and the integrated comparators enable hardware over-current trip without CPU latency. Running at 60 MHz/70 MIPS, deterministic interrupt response keeps control-loop jitter low, directly improving torque ripple and acoustic noise performance in servo and traction applications.
Disebarkan
Digital Power Supplies and PFC
The DSPIC33EP256MC502T-E/SO serves digital power applications such as power factor correction, LLC, and buck converters where fast, precise control loops are mandatory. The MCPWM peripheral supports high-resolution PWM with phase-shift and push-pull modes, matching topologies common in AC-DC front ends. Its DSP engine computes average-current-mode control efficiently, while the on-chip op amps condition current-shunt feedback and the three comparators provide primary-side peak-current protection with nanosecond-class hardware response. The 256 KB Flash supports adaptive control, soft-start sequencing, and digital communication for telemetry. The extended temperature grade supports power supplies operating in hot industrial cabinets near thermal limits.
Disebarkan
Industrial CAN Networking Nodes
With an integrated CAN module, the DSPIC33EP256MC502T-E/SO acts as an intelligent node on industrial CAN 2.0 buses used in factory automation, building control, and mobile equipment. The 70 MIPS core runs the application plus CAN stack concurrently, while 256 KB Flash stores protocol handling, diagnostics, and bootloader code for field firmware updates. Combined with its motor-control peripherals, one chip can close local servo loops and report status over CAN, removing a separate communication MCU. The -40C to +125C E-grade rating withstands unconditioned industrial environments, and the 28-pin SOIC fits compact I/O-node PCBs. Hardware-level peripheral support offloads frame buffering from software for deterministic bus latency.
Disebarkan
Automotive-Adjacent and Harsh Environment Systems
Although not AEC-Q100 qualified in the verified data, the -E extended temperature grade of the DSPIC33EP256MC502T-E/SO (-40C to +125C) makes it appropriate for harsh-environment equipment near automotive ecosystems: auxiliary pumps, agricultural actuators, and off-highway vehicle accessories. The extended rating ensures margins over the +85C industrial ceiling in engine-bay-adjacent enclosures, while the MCPWM, QEI, and comparator set drives and protects small motors directly. The 256 KB Flash permits redundant firmware images for safety-conscious updates, and CAN integration links the controller to vehicle networks. Designers must verify qualification requirements independently, since extended temperature alone does not substitute for automotive qualification.
Disebarkan
Embedded Sensing with On-Chip Analog
The two integrated operational amplifiers and three comparators on the DSPIC33EP256MC502T-E/SO enable compact sensing nodes: current monitoring, threshold detection, and signal conditioning without external analog ICs. Paired with the ADC (channel count per datasheet), the op amps can build programmable-gain front ends for shunt or sensor signals, while comparators generate interrupts for fast fault response. The 32 KB RAM buffers waveform captures for condition-monitoring analytics, and 256 KB Flash stores DSP filtering routines that exploit the DSC's MAC engine. In industrial monitoring and predictive-maintenance devices, this single-chip analog-plus-DSP integration shortens the signal chain and improves noise immunity over discrete op-amp layouts.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk DSPIC33EP256MC502T-E/SO — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | DSPIC33EP256MC502T-I/SO | DSPIC33EP256MC502-H/SO | DSPIC33EP128MC502-I/SO | DSPIC33EP64MC502-I/SO |
|---|---|---|---|---|---|
| Package | 28-pin SOIC | 28-pin SOIC - same | 28-pin SOIC - same | 28-pin SOIC - same | 28-pin SOIC - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Performance | 70 MIPS / 60 MHz | 70 MIPS / 60 MHz | 70 MIPS / 60 MHz | 70 MIPS / 60 MHz | 70 MIPS / 60 MHz |
| Flash Memory | 256 KB | 256 KB | 256 KB | 128 KB | 64 KB |
| Motor Control Peripherals (MCPWM/QEI/OpAmps/Comparators) | Yes / Yes / 2 / 3 | Yes / Yes / 2 / 3 | Yes / Yes / 2 / 3 | Yes / Yes / 2 / 3 | Yes / Yes / 2 / 3 |
| CAN Module | Yes | Yes | Yes | Yes | Yes |
| Packaging | Tape & Reel | Tape & Reel | Tube/Tray | Tube/Tray | Tube/Tray |
Penyeberangsung Jelas
- Extended -40C to +125C temperature rating (vsDSPIC33EP256MC502T-I/SO)
- Full 256 KB Flash for complex control firmware (vsDSPIC33EP128MC502-I/SO)
- Integrated analog (2 op amps, 3 comparators) reduces external BOM (vsGeneric non-DSC MCUs)
Catatan Desain
The 28-pin SOIC multiplexes MCPWM, QEI, CAN, UART, and analog functions across shared pins, and many digital functions are assignable via Peripheral Pin Select (PPS). Map all required peripherals in the pin planner BEFORE finalizing PCB routing - discovering a PPS conflict after layout forces a board respin. Also confirm which analog pins support the VREF+ configuration required by your current-sense accuracy budget.
Place 0.1 uF ceramic decoupling capacitors at each VDD pin pair as close to the package as possible, plus a bulk 4.7-10 uF capacitor near the controller. When driving a three-phase inverter, keep PWM outputs away from analog sense traces feeding the on-chip op amps; the integrated analog chain's accuracy depends on clean grounding. Use a solid ground plane and star-connect power grounds at the bulk capacitor to keep motor current loops out of the MCU ground return.
Verify the supply voltage range for this exact ordering code against the current family datasheet before production (see [DATA_NEEDED] marker on this page); dsPIC33EP-family parts are typically specified at 3.0-3.6 V operation. Brown-out behavior matters in motor drives: enable the internal brown-out reset so a sagging rail cannot leave MCPWM outputs in an undefined state while gate drivers remain powered, which could short the inverter bridge.
Maklumat Kesediaan
Compliance status for this specific ordering code was not stated in the verified web data. Lisleapex describes the part as AEC-Q-qualified for extreme temperatures; treat automotive qualification as unverified - confirm on Microchip's official compliance documentation before use in automotive programs.
