Silicon Labs

EFM32TG110F8-D-QFN24R - 32MHz Cortex-M3 Tiny Gecko MCU | Silicon Labs (Tape & Reel)

MPN: EFM32TG110F8-D-QFN24R ✓ Aktif
1.85 V to 3.8 V Vdss 150 uA/MHz Id 24-QFN (5 x 5 mm) Package 32 MHz Speed 8 KB (8K x 8) Memory
MOQ: 1 |

EFM32TG110F8-D-QFN24R Ringkasan

The Silicon Labs EFM32TG110F8-D-QFN24R is an ARM Cortex-M3 32-bit microcontroller running up to 32 MHz with 8 KB of Flash and 2 kB of RAM, housed in a 24-QFN (5 x 5 mm) surface-mount package. It is built on Silicon Labs' energy-friendly EFM32 platform, combining a low-power architecture with fast wake-up from energy-saving modes for battery-operated and energy-harvesting designs.

A microcontroller (MCU) is a single integrated circuit that contains a processor core, program memory, data memory and a set of dedicated peripherals such as timers, GPIO, serial interfaces and analog blocks. Within the component hierarchy, the EFM32TG110 sits in the ARM Cortex-M3 class of 32-bit embedded processors and in the EFM32 Tiny Gecko family of Silicon Labs low-power MCUs, a line positioned between the larger EFM32 Gecko and the ultra-low-power EFM32 Zero Gecko families for designs where energy cost per data point matters.

Key features of this device include an ARM Cortex-M3 core operating up to 32 MHz, 8 KB of Flash program memory organized as 8K x 8, 2 kB of SRAM, 17 digital I/O pins and two 16-bit timers. Silicon Labs specifies run-mode current of 150 uA/MHz and stop-mode current as low as 0.6 uA, which is the core reason the family is popular in coin-cell and sensor-node products. The device also integrates an AES hardware accelerator, analog peripherals including an operational amplifier, and a 2-pin serial-wire debug interface with a separate 1-wire Serial Wire Viewer pin for profiling and trace output.

Technically, the Tiny Gecko platform gives the EFM32TG110 fast wake-up times from its deep-sleep states, retention of output state in shutoff mode, and a peripheral set that can operate autonomously. This lets a design sleep at microamp current, wake, sample a sensor, transmit a short packet and return to sleep without the long wake latency typical of generic low-power MCUs, which directly reduces average current in duty-cycled nodes.

Typical applications include wireless sensor nodes and IoT end devices, industrial monitoring and metering, battery-powered handheld instruments, energy-harvesting sensors, smart home accessories and small motor or actuator control sub-systems where a full MCU plus glue logic would be over-specified.

When designing with the EFM32TG110F8-D-QFN24R, remember that its 2 kB of RAM is the real design constraint: keep stack depth, DMA buffers and protocol buffers lean, and prefer the 8 KB Flash part only for code sizes that genuinely fit. Route the two SWD debug pins to test points so the board can be programmed and profiled in production.

This page consolidates device specifications, drop-in alternatives in the same 24-QFN footprint, a parameter-by-parameter comparison, and practical low-power design notes so engineers can qualify the part against a second source and plan a board layout in one pass.

Pilihan pengganti yang segera untuk EFM32TG110F8-D-QFN24R — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera EFM32TG110F8-D-QFN24R (sama faktor bentuk dan kaki) — berbeza dalam Package, Flash Memory, Stop Mode Current, Series, Supply Voltage Range.

Silicon Labs
Package: 24-QFN (5 mm x 5 mm)
Flash Memory: 8 kB
Supply Voltage Range: 1.85 V to 3.8 V
Bandingkan Dengan EFM32TG110F8-D-QFN24R →
Silicon Labs
Package: 24-QFN, 5 x 5 mm
Flash Memory: 4 kB
Stop Mode Current: As low as 0.6 uA
Bandingkan Dengan EFM32TG110F8-D-QFN24R →
Silicon Labs
Supply Voltage Range: 1.85 V to 3.8 V
Bandingkan Dengan EFM32TG110F8-D-QFN24R →
Silicon Labs
Flash Memory: 4 KB
Stop Mode Current: 0.5 microamp minimum
Series: EFM32 Zero Gecko
Bandingkan Dengan EFM32TG110F8-D-QFN24R →

EFM32TG110F8-QFN24

✅ Masuk Drop-In
Silicon Labs
📦 QFN-24 (5x5)
32-bit ARM Cortex-M3 microcontroller · Tiny Gecko · 32 MHz · ARM Cortex-M3 · 8 kB Flash · 2 kB RAM · 17 · 2 x 16-bit timers

Hubungi untuk harga

Lihat Datasheet →

EFM32TG110F16-D-QFN24

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 QFN-24 (5x5)
Same Cortex-M3 core, 32 MHz, 17 I/O and 24-QFN (5x5) package, but 16 KB Flash vs 8 KB Flash (+100% code space); RAM unchanged at 2 kB

📋 Alternatif rujukan (tidak dalam katalog)

EFM32TG110F4-D-QFN24

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
Silicon Labs
📦 QFN-24 (5x5)
32-bit ARM Cortex-M3 microcontroller · 32 MHz · 4 kB · 2 kB · 17 · 2 x 16-bit timers · 1.98 V to 3.8 V · ARM Cortex-M3

Hubungi untuk harga

Lihat Datasheet →

EFM32TG108F8-QFN24

✅ Masuk Drop-In
Silicon Labs
📦 QFN-24 (5x5)
32-bit ARM Cortex-M3 microcontroller · ARM Cortex-M3 · 32 MHz · 8 kB · 2 kB · 17 · 2 x 16-bit timers · Tiny Gecko

Hubungi untuk harga

Lihat Datasheet →

EFM32ZG110F4-B-QFN24

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
Silicon Labs
📦 QFN-24 (5x5)
ARM Cortex-M0+ · 24 MHz · 32-bit · 4 KB · 2 KB · 17 · 2 x 16-bit · 1.98 V to 3.8 V

Hubungi untuk harga

Lihat Datasheet →

EFM32TG110F8-QFN24T

✅ Masuk Drop-In
Silicon Labs
📦 QFN-24 (5x5)
32-bit ARM Cortex-M3 microcontroller · 32 MHz · 8 kB · 2 kB · 17 · 2 · 16-bit · 1.85 V to 3.8 V

Hubungi untuk harga

Lihat Datasheet →

EFM32TG110F8-D-QFN24R Penilaian maksimum & Ciri-ciri Elektrik

Core ARM Cortex-M3, 32-bit
Frekuensi Klock Maksimum 32 MHz
Flash Memory 8 KB (8K x 8)
RAM (SRAM) 2 kB
Digital I/O Pins 17
Supply Voltage Range (Vcc/Vdd) 1.85 V to 3.8 V
Timers 2 x 16-bit
Series Tiny Gecko
Kemasan 24-QFN (5 x 5 mm)
Jenis Pemasangan Surface Mount
Run Mode Current 150 uA/MHz
Stop Mode Current 0.6 uA
Security Accelerator AES hardware accelerator
Analog Peripherals Operational amplifier (OPAMP)
Debug Interface 2-pin Serial Wire Debug (SWD)
Trace Interface 1-wire Serial Wire Viewer (SWV) pin
Low-Power Modes Deep sleep / shutoff mode with output state retention

Panduan Konfigurasi Pin EFM32TG110F8-D-QFN24R 24-qfn (5 x 5 mm)

Konfigurasi pin untuk EFM32TG110F8-D-QFN24R (24-qfn (5 x 5 mm) pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.

Garis bentuk pengecah pakai 24-qfn (5 x 5 mm) untuk EFM32TG110F8-D-QFN24R

Tiada data garisan pin yang diperoleh untuk EFM32TG110F8-D-QFN24R.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

EFM32TG110F8-D-QFN24R patut untuk 6 aplikasis: Battery-Powered Wireless Sensor Node, Energy-Harvesting IoT Sensor, Industrial Metering and Monitoring, Battery-Powered Handheld Instrument, Smart Home Accessory and Sensor Node, Low-Power Actuator and Motor Sub-System.

🧩

Battery-Powered Wireless Sensor Node

The EFM32TG110F8-D-QFN24R suits wireless sensor nodes where the average current of the radio duty cycle dominates the battery budget. Silicon Labs specifies run-mode current of 150 uA/MHz and stop-mode current as low as 0.6 uA, and the Tiny Gecko architecture wakes quickly and retains output state in shutoff, so the node can sleep for hours, wake, sample, transmit a short packet and return to sleep without paying a long wake penalty. The 1.85 V to 3.8 V supply window lets the same board run from a coin cell, a 3 V lithium cell or a 2.8 V backup pack. Budget firmware size carefully against the 8 KB Flash and keep radio buffers inside the 2 kB SRAM.

🔋

Energy-Harvesting IoT Sensor

In energy-harvesting designs the harvested budget is tiny, so every microamp counts and the EFM32TG110F8-D-QFN24R's low-power modes are the deciding factor. The 0.6 uA stop-mode figure from the Silicon Labs EFM32TG data sheet means the device can sit in deep sleep through most of the cycle with minimal draw, while the fast wake-up behavior lets the firmware capture and process a measurement immediately when the harvester is charged. The operational amplifier integrated in the Tiny Gecko family can condition a low-level sensor signal without a separate amplifier, and the AES accelerator handles encrypted payloads locally. The 5 x 5 mm 24-QFN footprint also keeps the board area small, which matters when the node is limited by the harvesting area itself.

🏭

Industrial Metering and Monitoring

Utility meters, flow monitors and environmental sensors repeatedly sample slow-moving quantities over long service lives, a workload that matches the EFM32TG110F8-D-QFN24R's combination of low active current and deep-sleep capability. Two 16-bit timers give accurate interval measurement and pulse counting for flow meters without a companion timer IC, and the 17 available digital I/O pins cover reed switches, tamper detection, status LEDs and alarm outputs. The 1.85 V minimum operating voltage supports designs powered from a 2.5 V or 3 V regulated industrial rail with brown-out margin, and the industrial temperature grade variants exist across the family. Serial-wire debug and the Serial Wire Viewer pin allow in-field profiling of wake timing without disturbing the measurement chain.

📟

Battery-Powered Handheld Instrument

Compact handheld meters, loggers and diagnostic probes benefit from the EFM32TG110F8-D-QFN24R because the Cortex-M3 core at up to 32 MHz can service a small display, keypad scanning and a serial link while the part still sleeps at microamp current between user actions. The 8 KB Flash is workable for a lean UI and logging application, while the 2 kB SRAM suits a display buffer and a short record set rather than long acquisition sweeps. Deep-sleep current of 0.6 uA extends the interval between charges on a small lithium cell, and the 5 x 5 mm QFN keeps the board small enough for a handheld enclosure. Use the SWD header footprint for final programming and calibration.

🏠

Smart Home Accessory and Sensor Node

Smart home accessories such as door contacts, leak sensors, thermostats and occupancy detectors need low standby consumption and always-available local control, which is exactly what the EFM32TG110F8-D-QFN24R delivers with its 0.6 uA stop-mode floor and 150 uA/MHz run current. Seventeen I/O pins are enough to drive a reed switch, a PIR output, a piezo or a status LED directly, reducing the bill of materials compared with a discrete controller. The 1.85 V to 3.8 V operating range accepts both coin-cell and 3 V rail-fed products, and the integrated AES accelerator suits encrypted device-to-cloud links. Because the family is mature and widely supported, firmware ports and community middleware for the EFM32 platform shorten development time.

⚙️

Low-Power Actuator and Motor Sub-System

Small actuators, valve drivers, fan controllers and stepper sub-systems that must sit idle for long periods can use the EFM32TG110F8-D-QFN24R as a compact supervisory controller. The two 16-bit timers generate the pulse trains and dead-time windows needed to sequence a small motor or solenoid, and the 17 I/O pins cover direction, limit and home sensors. Deep sleep with output state retention means the driver can be parked safely between commands without forcing the whole board into a reset cycle, and the 150 uA/MHz figure keeps active consumption low while the motor is running. The 24-QFN (5 x 5 mm) package leaves board area for the power stage, and the 1.85 V minimum supply works with 3.3 V logic-compatible gate drivers.

What are the key specifications of the EFM32TG110F8-D-QFN24R that engineers should know?
The EFM32TG110F8-D-QFN24R is a 32-bit ARM Cortex-M3 microcontroller running up to 32 MHz with 8 KB of Flash, 2 kB of RAM and 17 digital I/O pins in a 24-QFN (5 x 5 mm) package. According to the Silicon Labs EFM32TG datasheet, it consumes 150 uA/MHz in run mode and as little as 0.6 uA in stop mode, operates from a 1.85 V to 3.8 V supply, and provides two 16-bit timers, an AES hardware accelerator, an operational amplifier, a 2-pin serial-wire debug port and a 1-wire Serial Wire Viewer trace pin.
What is the EFM32TG110F8-D-QFN24R?
The EFM32TG110F8-D-QFN24R is a Silicon Labs Tiny Gecko family microcontroller, part of the EFM32 low-power platform, built around an ARM Cortex-M3 core. The Silicon Labs EFM32TG datasheet describes the family as combining the 32-bit Cortex-M3 processor with low-energy techniques, short wake-up times from energy-saving modes and autonomous peripherals. This particular orderable device carries 8 KB of Flash, 2 kB of RAM and 17 I/O pins in a 24-QFN package, and is aimed at battery-operated and energy-harvesting applications.
What is the operating voltage of the EFM32TG110F8-D-QFN24R?
The EFM32TG110F8-D-QFN24R operates from a 1.85 V to 3.8 V supply. According to the Silicon Labs EFM32TG110 datasheet, this single 1.8 V-class operating window covers both 1.8 V coin-cell and 3 V lithium chemistries, which means the same board design can often cover several battery types. Because the core runs down to 1.85 V, the usable energy of a 3 V cell is better exploited than with a part that needs 2.0 V or more, an advantage in long-life sensor nodes.
How much Flash and RAM does the EFM32TG110F8-D-QFN24R have?
The EFM32TG110F8-D-QFN24R provides 8 KB of Flash program memory organized as 8K x 8 and 2 kB of RAM. The Silicon Labs EFM32TG datasheet specifies this combination for the F8 density variant of the TG110 family. With 2 kB of SRAM, keep the stack, driver buffers and radio/protocol buffers conservative; if a protocol stack, bootloader or larger application is planned, step up to the 16 KB Flash density of the same package rather than fighting the RAM limit.
What is the maximum clock speed of the EFM32TG110F8-D-QFN24R?
The EFM32TG110F8-D-QFN24R runs at up to 32 MHz from its ARM Cortex-M3 core, as stated in the Silicon Labs EFM32TG110 datasheet and confirmed on the manufacturer product page. At that speed the part is fast enough for small protocol stacks, sensor fusion, control loops and simple UI servicing, while the EFM32 energy-saving architecture lets it drop to deep-sleep states between events with microsecond-class wake-up response.
Where can I download the EFM32TG110F8-D-QFN24R datasheet PDF?
The EFM32TG110F8-D-QFN24R datasheet PDF is published by Silicon Labs as part of the EFM32TG family data sheet, available from the manufacturer's data-sheets section, and the device-specific page is hosted on silabs.com under the EFM32 Tiny Gecko product range. The family document covers the TG110, TG111, TG210 and TG211 derivatives in a single file, including the pin description table, electrical characteristics, memory map and the low-power and sleep-mode tables you need for battery budget calculations.
Where can I find the EFM32TG110F8-D-QFN24R pinout?
The EFM32TG110F8-D-QFN24R pinout is published in the pin configuration and pin description tables of the Silicon Labs EFM32TG family data sheet, with the 24-QFN (5 x 5 mm) land pattern drawn in the package dimensions section. Use the pin-description table in that document when assigning PCB tracks, particularly for the 2-pin serial-wire debug interface (SWDIO and SWCLK), the 1-wire Serial Wire Viewer pin, the analog and ground pins, and the exposed pad connection.
Where can I buy the EFM32TG110F8-D-QFN24R online?
You can request a quote for the EFM32TG110F8-D-QFN24R through the Request a Quote form on this page, which is the fastest route to current stock status, lead time and volume pricing for the 24-QFN (5 x 5 mm) package. The part is an active Silicon Labs orderable type in the EFM32 Tiny Gecko family, so supply is managed through authorized distribution channels; submitting the MPN and required quantity against this page gives a direct, traceable quotation.
What is the price of the EFM32TG110F8-D-QFN24R?
Pricing for the EFM32TG110F8-D-QFN24R is quote-based and is not published as a fixed figure on this page. Use the Request a Quote form on this page to receive current pricing for the 24-QFN (5 x 5 mm) orderable type, including any quantity breaks for volume builds. Silicon Labs EFM32 Tiny Gecko MCUs are distributed through authorized channels, so a quotation against the exact MPN also confirms the packaging and date code configuration you will actually receive.
What is the lead time and stock status of the EFM32TG110F8-D-QFN24R?
Current stock status and lead time for the EFM32TG110F8-D-QFN24R are confirmed through the Request a Quote form on this page, where the quantity and target delivery date can be stated. The manufacturer lists the EFM32TG110F8-D-QFN24R as an active device in the EFM32 Tiny Gecko family. Because lead time varies with order quantity, package form and market conditions, request the quotation with your required volume and date-code requirements rather than relying on a generic availability figure.
What is the difference between the EFM32TG110F8-D-QFN24R and the EFM32TG108F8-QFN24?
The EFM32TG110F8-D-QFN24R and the EFM32TG108F8-QFN24 are both 8 KB Flash ARM Cortex-M3 Tiny Gecko MCUs in the same 24-QFN (5 x 5 mm) footprint, but they differ in memory and timer resources. The TG110 provides 2 kB of RAM and two 16-bit timers as listed in the Silicon Labs EFM32TG data sheet, while the TG108 is the leaner 1 KB RAM derivative with fewer timers. Choose TG110 for protocol buffering and multi-timer work; TG108 only if the extra memory is genuinely unused.
Is the EFM32TG110F8-D-QFN24R the same as the EFM32TG110F8-QFN24?
The EFM32TG110F8-D-QFN24R and the EFM32TG110F8-QFN24 are the same Silicon Labs EFM32TG110F8 silicon in the same 24-QFN (5 x 5 mm) package, differing only in the ordering suffix that defines the lead-free and packaging configuration. Because the die, footprint and pinout are identical, one is a drop-in substitute for the other at the board level. Confirm the suffix against your purchasing specification and assembly house requirements before substituting.
When should I choose the EFM32TG110F8-D-QFN24R over the EFM32TG110F4-D-QFN24?
Choose the EFM32TG110F8-D-QFN24R when your application needs more than a few kilobytes of code or a stack that will not fit in the smaller density. The F8 device carries 8 KB of Flash and 2 kB of RAM while the F4 density provides only 4 KB of Flash in the identical 24-QFN (5 x 5 mm) footprint, so the F4 saves flash and cost but constrains code size and buffer space. Both share the same Cortex-M3 core, 32 MHz clock and 1.85 V to 3.8 V supply range.
Is the EFM32TG110F8-D-QFN24R suitable for a battery-powered sensor node?
Yes, the EFM32TG110F8-D-QFN24R is well suited to battery-powered sensor nodes. The Silicon Labs EFM32TG data sheet specifies run-mode current of 150 uA/MHz and stop-mode current as low as 0.6 uA, plus fast wake-up from the energy-saving modes with output state retention in shutoff. That combination lets a duty-cycled node wake, sample, transmit and return to sleep quickly, keeping average current low. Verify the 1.85 V minimum supply against your cell type and confirm the brown-out margin in your final layout.
What can replace the EFM32TG110F8-D-QFN24R?
The closest drop-in replacements for the EFM32TG110F8-D-QFN24R are the same Silicon Labs Tiny Gecko parts in the identical 24-QFN (5 x 5 mm) footprint, notably EFM32TG110F8-QFN24 (identical silicon, different ordering suffix) and EFM32TG110F16-D-QFN24, which offers more Flash in the same package. The EFM32TG108F8-QFN24 is a lower-memory option that also fits the footprint. All are drop-in at the pin level but differ in code space, so a firmware re-verification is required after any swap.
Is there a non-Silicon Labs drop-in replacement for the EFM32TG110F8-D-QFN24R?
No pin-compatible cross-brand replacement was identified for the EFM32TG110F8-D-QFN24R. The part's 24-QFN (5 x 5 mm) 17-I/O Tiny Gecko pinout is Silicon Labs specific, and its EFM32 energy-saving architecture, peripheral set and low-power behaviour are not reproduced by another manufacturer's 24-QFN Cortex-M3 device. A third-party MCU in the same package size would be a functional replacement requiring a full board, firmware and peripheral re-design, not a drop-in substitution, so treat any cross-brand swap as a redesign rather than a second source.

Data referensi kejuruteraan untuk EFM32TG110F8-D-QFN24R — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the EFM32TG110F8-D-QFN24R when your design is a duty-cycled, battery-operated node that needs a 32-bit Cortex-M3 with 8 KB of Flash, 2 kB of RAM and 17 I/O pins in a compact 5 x 5 mm QFN. Prefer EFM32TG110F16-D-QFN24 when the firmware is tight, since the extra 8 KB of Flash arrives in the identical footprint at no layout cost. Choose EFM32TG110F4-D-QFN24 only after confirming that the application image fits in 4 KB, accepting less headroom for later feature work. Use EFM32TG108F8-QFN24 when board space and memory are not constraints and you want to move down to 1 kB SRAM, but re-check any buffer-heavy code. EFM32ZG110F4-B-QFN24 suits designs where standby current matters more than code size. There is no pin-compatible cross-brand option, so a second source must come from the same EFM32 Tiny Gecko range.

Perbandingan dengan Gantian

Parametr Produk Ini EFM32TG110F8-QFN24 EFM32TG110F16-D-QFN24 EFM32TG110F4-D-QFN24 EFM32TG108F8-QFN24 EFM32ZG110F4-B-QFN24
Package QFN-24 (5x5) QFN-24 (5x5) - same QFN-24 (5x5) - same QFN-24 (5x5) - same QFN-24 (5x5) - same QFN-24 (5x5) - same
Brand Silicon Labs Silicon Labs Silicon Labs Silicon Labs Silicon Labs Silicon Labs
Core ARM Cortex-M3, 32-bit ARM Cortex-M3, 32-bit ARM Cortex-M3, 32-bit ARM Cortex-M3, 32-bit ARM Cortex-M3, 32-bit ARM Cortex-M3, 32-bit
Flash Memory 8 KB (8K x 8) 8 KB (8K x 8) 16 KB 4 KB 8 KB 4 KB
Series Tiny Gecko Tiny Gecko Tiny Gecko Tiny Gecko Tiny Gecko Zero Gecko

Penyeberangsung Jelas

  • Doubles the code space without changing the footprint (vsEFM32TG110F4-D-QFN24)
  • Twice the data memory of the leaner TG108 derivative (vsEFM32TG108F8-QFN24)
  • Direct silicon equivalent for second-source builds (vsEFM32TG110F8-QFN24)
  • Higher code density than the Zero Gecko alternative in the same package (vsEFM32ZG110F4-B-QFN24)

Catatan Desain

Build the average-current budget from the datasheet duty cycle: run-mode current is 150 uA/MHz and stop mode is 0.6 uA. Estimated example for a 32 MHz node that wakes for 2 ms every 10 s: active current is about 4.8 mA for 2 ms, which contributes roughly 0.96 uA average, while the remaining sleep time contributes about 0.59 uA, for a total near 1.55 uA average. Estimated values, based on the published run and stop current figures. This calculation shows why reducing wake duration matters far more than reducing standby current once the device is already at 0.6 uA.

Decoupling for this MCU must be placed on the same side of the board as the device and referenced by the shortest possible loop. Use one 100 nF ceramic capacitor close to each supply pin and bulk ceramic capacitance close to the device, following the recommended values in the Silicon Labs EFM32TG data sheet. Keep the analog and digital return paths separated so the integrated operational amplifier and analog inputs are not referenced into switching-node current. The 24-QFN (5 x 5 mm) footprint has tight pad pitch, so verify the land pattern and paste stencil against the package drawing before releasing the PCB.

The most common design failure with this part is a firmware image that fits in 8 KB of Flash but overflows the 2 kB of SRAM once the stack, peripheral buffers and a communication stack are linked. Estimate stack high-water mark early, use the linker map file, and avoid allocating large static buffers on top of the stack. The second pitfall is assuming 3.0 V rail headroom: the device operates from 1.85 V to 3.8 V, so a 3.7 V lithium cell must be regulated or the brown-out behaviour must be accounted for in the firmware.

Reserve the two serial-wire debug pins (SWDIO and SWCLK) as accessible test pads even in production boards, and bring out the 1-wire Serial Wire Viewer pin if in-field profiling is planned. Because the device can wake from deep sleep in microseconds, debugging a low-power design without SWD is extremely difficult; with the trace pin connected, current consumption and wake timing can be observed directly. Keep these nets away from switching regulators and antenna keep-out areas, and provide a ground reference pad adjacent to them for cleaner signal capture.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The manufacturer product page and family datasheet were used for electrical and package data; no explicit RoHS, REACH, lead-free or conflict-minerals statement was published on the pages consulted, so these fields remain unknown. This device is an industrial/consumer MCU and is not marketed as an AEC-Q100 automotive-qualified part in the data reviewed.

Pencarian Berhubungan

EFM32TG110F8-D-QFN24R EFM32TG110F8-D-QFN24R datasheet EFM32TG110F8-D-QFN24R datasheet pdf EFM32TG110F8-D-QFN24R pinout EFM32TG110F8-D-QFN24R equivalent EFM32TG110F8-D-QFN24R replacement EFM32TG110F8-D-QFN24R price EFM32TG110F8-D-QFN24R stock Silicon Labs EFM32TG110F8 EFM32TG110F8-QFN24 EFM32TG110F16 vs EFM32TG110F8 EFM32 Tiny Gecko 24-QFN 5x5 microcontroller Cortex-M3 low power MCU 1.85V 32MHz EFM32TG110F8-D-QFN24R application circuit

Komponen dan Tanda berkaitan

Silicon Labs EFM32TG110F8-D-QFN24R EFM32TG110F8-QFN24 EFM32TG110F16-D-QFN24 EFM32TG108F8-QFN24 EFM32ZG110F4-B-QFN24 EFM32 Tiny Gecko EFM32 Zero Gecko ARM Cortex-M3 microcontroller MCU embedded processor 32-bit microcontroller semiconductor low-power MCU energy harvesting wireless sensor node IoT end device QFN-24 (5x5) QFN package family surface mount SMD serial wire debug SWD AES operational amplifier stop mode deep sleep coin cell battery RoHS REACH
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ