EFM32TG110F8-D-QFN24R - 32MHz Cortex-M3 Tiny Gecko MCU | Silicon Labs (Tape & Reel)
MPN: EFM32TG110F8-D-QFN24R ✓ Hoạt độngEFM32TG110F8-D-QFN24R Tóm tắt
A microcontroller (MCU) is a single integrated circuit that contains a processor core, program memory, data memory and a set of dedicated peripherals such as timers, GPIO, serial interfaces and analog blocks. Within the component hierarchy, the EFM32TG110 sits in the ARM Cortex-M3 class of 32-bit embedded processors and in the EFM32 Tiny Gecko family of Silicon Labs low-power MCUs, a line positioned between the larger EFM32 Gecko and the ultra-low-power EFM32 Zero Gecko families for designs where energy cost per data point matters.
Key features of this device include an ARM Cortex-M3 core operating up to 32 MHz, 8 KB of Flash program memory organized as 8K x 8, 2 kB of SRAM, 17 digital I/O pins and two 16-bit timers. Silicon Labs specifies run-mode current of 150 uA/MHz and stop-mode current as low as 0.6 uA, which is the core reason the family is popular in coin-cell and sensor-node products. The device also integrates an AES hardware accelerator, analog peripherals including an operational amplifier, and a 2-pin serial-wire debug interface with a separate 1-wire Serial Wire Viewer pin for profiling and trace output.
Technically, the Tiny Gecko platform gives the EFM32TG110 fast wake-up times from its deep-sleep states, retention of output state in shutoff mode, and a peripheral set that can operate autonomously. This lets a design sleep at microamp current, wake, sample a sensor, transmit a short packet and return to sleep without the long wake latency typical of generic low-power MCUs, which directly reduces average current in duty-cycled nodes.
Typical applications include wireless sensor nodes and IoT end devices, industrial monitoring and metering, battery-powered handheld instruments, energy-harvesting sensors, smart home accessories and small motor or actuator control sub-systems where a full MCU plus glue logic would be over-specified.
When designing with the EFM32TG110F8-D-QFN24R, remember that its 2 kB of RAM is the real design constraint: keep stack depth, DMA buffers and protocol buffers lean, and prefer the 8 KB Flash part only for code sizes that genuinely fit. Route the two SWD debug pins to test points so the board can be programmed and profiled in production.
This page consolidates device specifications, drop-in alternatives in the same 24-QFN footprint, a parameter-by-parameter comparison, and practical low-power design notes so engineers can qualify the part against a second source and plan a board layout in one pass.
Bộ thay thế dễ dàng lắp đặt cho EFM32TG110F8-D-QFN24R — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EFM32TG110F8-D-QFN24R (cùng hình factor và footprint) — khác nhau ở Package, Flash Memory, Stop Mode Current, Series, Supply Voltage Range.
EFM32TG110F8-QFN24
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EFM32TG110F16-D-QFN24
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
EFM32TG110F4-D-QFN24
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →EFM32TG108F8-QFN24
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EFM32ZG110F4-B-QFN24
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →EFM32TG110F8-QFN24T
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EFM32TG110F8-D-QFN24R Tỷ lệ tối đa & tính chất điện
| Core | ARM Cortex-M3, 32-bit |
| Tần số xung maksimum | 32 MHz |
| Flash Memory | 8 KB (8K x 8) |
| RAM (SRAM) | 2 kB |
| Digital I/O Pins | 17 |
| Supply Voltage Range (Vcc/Vdd) | 1.85 V to 3.8 V |
| Timers | 2 x 16-bit |
| Series | Tiny Gecko |
| Hộp | 24-QFN (5 x 5 mm) |
| Kiểu lắp đặt | Surface Mount |
| Run Mode Current | 150 uA/MHz |
| Stop Mode Current | 0.6 uA |
| Security Accelerator | AES hardware accelerator |
| Analog Peripherals | Operational amplifier (OPAMP) |
| Debug Interface | 2-pin Serial Wire Debug (SWD) |
| Trace Interface | 1-wire Serial Wire Viewer (SWV) pin |
| Low-Power Modes | Deep sleep / shutoff mode with output state retention |
Hướng dẫn cấu hình chân EFM32TG110F8-D-QFN24R 24-qfn (5 x 5 mm)
Cấu hình chân cho EFM32TG110F8-D-QFN24R (24-qfn (5 x 5 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho EFM32TG110F8-D-QFN24R.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
EFM32TG110F8-D-QFN24R phù hợp cho 6 Áp dụngs: Battery-Powered Wireless Sensor Node, Energy-Harvesting IoT Sensor, Industrial Metering and Monitoring, Battery-Powered Handheld Instrument, Smart Home Accessory and Sensor Node, Low-Power Actuator and Motor Sub-System.
Battery-Powered Wireless Sensor Node
The EFM32TG110F8-D-QFN24R suits wireless sensor nodes where the average current of the radio duty cycle dominates the battery budget. Silicon Labs specifies run-mode current of 150 uA/MHz and stop-mode current as low as 0.6 uA, and the Tiny Gecko architecture wakes quickly and retains output state in shutoff, so the node can sleep for hours, wake, sample, transmit a short packet and return to sleep without paying a long wake penalty. The 1.85 V to 3.8 V supply window lets the same board run from a coin cell, a 3 V lithium cell or a 2.8 V backup pack. Budget firmware size carefully against the 8 KB Flash and keep radio buffers inside the 2 kB SRAM.
Được đề xuất
Energy-Harvesting IoT Sensor
In energy-harvesting designs the harvested budget is tiny, so every microamp counts and the EFM32TG110F8-D-QFN24R's low-power modes are the deciding factor. The 0.6 uA stop-mode figure from the Silicon Labs EFM32TG data sheet means the device can sit in deep sleep through most of the cycle with minimal draw, while the fast wake-up behavior lets the firmware capture and process a measurement immediately when the harvester is charged. The operational amplifier integrated in the Tiny Gecko family can condition a low-level sensor signal without a separate amplifier, and the AES accelerator handles encrypted payloads locally. The 5 x 5 mm 24-QFN footprint also keeps the board area small, which matters when the node is limited by the harvesting area itself.
Được đề xuất
Industrial Metering and Monitoring
Utility meters, flow monitors and environmental sensors repeatedly sample slow-moving quantities over long service lives, a workload that matches the EFM32TG110F8-D-QFN24R's combination of low active current and deep-sleep capability. Two 16-bit timers give accurate interval measurement and pulse counting for flow meters without a companion timer IC, and the 17 available digital I/O pins cover reed switches, tamper detection, status LEDs and alarm outputs. The 1.85 V minimum operating voltage supports designs powered from a 2.5 V or 3 V regulated industrial rail with brown-out margin, and the industrial temperature grade variants exist across the family. Serial-wire debug and the Serial Wire Viewer pin allow in-field profiling of wake timing without disturbing the measurement chain.
Được đề xuất
Battery-Powered Handheld Instrument
Compact handheld meters, loggers and diagnostic probes benefit from the EFM32TG110F8-D-QFN24R because the Cortex-M3 core at up to 32 MHz can service a small display, keypad scanning and a serial link while the part still sleeps at microamp current between user actions. The 8 KB Flash is workable for a lean UI and logging application, while the 2 kB SRAM suits a display buffer and a short record set rather than long acquisition sweeps. Deep-sleep current of 0.6 uA extends the interval between charges on a small lithium cell, and the 5 x 5 mm QFN keeps the board small enough for a handheld enclosure. Use the SWD header footprint for final programming and calibration.
Được đề xuất
Smart Home Accessory and Sensor Node
Smart home accessories such as door contacts, leak sensors, thermostats and occupancy detectors need low standby consumption and always-available local control, which is exactly what the EFM32TG110F8-D-QFN24R delivers with its 0.6 uA stop-mode floor and 150 uA/MHz run current. Seventeen I/O pins are enough to drive a reed switch, a PIR output, a piezo or a status LED directly, reducing the bill of materials compared with a discrete controller. The 1.85 V to 3.8 V operating range accepts both coin-cell and 3 V rail-fed products, and the integrated AES accelerator suits encrypted device-to-cloud links. Because the family is mature and widely supported, firmware ports and community middleware for the EFM32 platform shorten development time.
Được đề xuất
Low-Power Actuator and Motor Sub-System
Small actuators, valve drivers, fan controllers and stepper sub-systems that must sit idle for long periods can use the EFM32TG110F8-D-QFN24R as a compact supervisory controller. The two 16-bit timers generate the pulse trains and dead-time windows needed to sequence a small motor or solenoid, and the 17 I/O pins cover direction, limit and home sensors. Deep sleep with output state retention means the driver can be parked safely between commands without forcing the whole board into a reset cycle, and the 150 uA/MHz figure keeps active consumption low while the motor is running. The 24-QFN (5 x 5 mm) package leaves board area for the power stage, and the 1.85 V minimum supply works with 3.3 V logic-compatible gate drivers.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EFM32TG110F8-D-QFN24R — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EFM32TG110F8-QFN24 | EFM32TG110F16-D-QFN24 | EFM32TG110F4-D-QFN24 | EFM32TG108F8-QFN24 | EFM32ZG110F4-B-QFN24 |
|---|---|---|---|---|---|---|
| Package | QFN-24 (5x5) | QFN-24 (5x5) - same | QFN-24 (5x5) - same | QFN-24 (5x5) - same | QFN-24 (5x5) - same | QFN-24 (5x5) - same |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Core | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit |
| Flash Memory | 8 KB (8K x 8) | 8 KB (8K x 8) | 16 KB | 4 KB | 8 KB | 4 KB |
| Series | Tiny Gecko | Tiny Gecko | Tiny Gecko | Tiny Gecko | Tiny Gecko | Zero Gecko |
Bảo phân biệt quan trọng
- Doubles the code space without changing the footprint (vsEFM32TG110F4-D-QFN24)
- Twice the data memory of the leaner TG108 derivative (vsEFM32TG108F8-QFN24)
- Direct silicon equivalent for second-source builds (vsEFM32TG110F8-QFN24)
- Higher code density than the Zero Gecko alternative in the same package (vsEFM32ZG110F4-B-QFN24)
Ghi chú thiết kế
Build the average-current budget from the datasheet duty cycle: run-mode current is 150 uA/MHz and stop mode is 0.6 uA. Estimated example for a 32 MHz node that wakes for 2 ms every 10 s: active current is about 4.8 mA for 2 ms, which contributes roughly 0.96 uA average, while the remaining sleep time contributes about 0.59 uA, for a total near 1.55 uA average. Estimated values, based on the published run and stop current figures. This calculation shows why reducing wake duration matters far more than reducing standby current once the device is already at 0.6 uA.
Decoupling for this MCU must be placed on the same side of the board as the device and referenced by the shortest possible loop. Use one 100 nF ceramic capacitor close to each supply pin and bulk ceramic capacitance close to the device, following the recommended values in the Silicon Labs EFM32TG data sheet. Keep the analog and digital return paths separated so the integrated operational amplifier and analog inputs are not referenced into switching-node current. The 24-QFN (5 x 5 mm) footprint has tight pad pitch, so verify the land pattern and paste stencil against the package drawing before releasing the PCB.
The most common design failure with this part is a firmware image that fits in 8 KB of Flash but overflows the 2 kB of SRAM once the stack, peripheral buffers and a communication stack are linked. Estimate stack high-water mark early, use the linker map file, and avoid allocating large static buffers on top of the stack. The second pitfall is assuming 3.0 V rail headroom: the device operates from 1.85 V to 3.8 V, so a 3.7 V lithium cell must be regulated or the brown-out behaviour must be accounted for in the firmware.
Reserve the two serial-wire debug pins (SWDIO and SWCLK) as accessible test pads even in production boards, and bring out the 1-wire Serial Wire Viewer pin if in-field profiling is planned. Because the device can wake from deep sleep in microseconds, debugging a low-power design without SWD is extremely difficult; with the trace pin connected, current consumption and wake timing can be observed directly. Keep these nets away from switching regulators and antenna keep-out areas, and provide a ground reference pad adjacent to them for cleaner signal capture.
Thông tin tuân thủ
The manufacturer product page and family datasheet were used for electrical and package data; no explicit RoHS, REACH, lead-free or conflict-minerals statement was published on the pages consulted, so these fields remain unknown. This device is an industrial/consumer MCU and is not marketed as an AEC-Q100 automotive-qualified part in the data reviewed.