ICL7653CPA - Zero-Drift 2 MHz Op Amp | Maxim Integrated
MPN: ICL7653CPA ✓ AktifICL7653CPA Ringkasan
A chopper-stabilized operational amplifier is an amplifier whose low-frequency offset and drift are reduced by continuously detecting and correcting low-frequency error components. In the signal-chain hierarchy, this device belongs to the operational-amplifier family and provides the closed-loop gain, filtering, and input-buffering functions required between sensors and higher-level measurement or control circuitry. It differs from a general-purpose precision amplifier through its zero-drift architecture and unusually low 4 pA input bias current.
The ICL7653CPA provides a 2 MHz gain-bandwidth product and a 2.5 V/us slew rate. Its amplifier type is identified as chopper, or zero drift, and the device contains one amplifier circuit. The specified operating range includes 0°C to +70°C, making the CPA grade appropriate for commercial-temperature equipment. The 8-pin PDIP format also supports conventional through-hole assembly, prototyping, repair, and designs that favor socketed or manually inspected connections.
Chopper stabilization trades some additional internal complexity for reduced low-frequency error. This is particularly beneficial when the desired signal changes slowly and a conventional amplifier’s input offset would otherwise create unacceptable measurement error. The 2 MHz gain-bandwidth product remains sufficient for a broad range of low-level signal paths, while the 2.5 V/us slew rate allows the amplifier to respond to higher-frequency components without changing the basic zero-drift operating approach.
Typical applications include precision current-to-voltage conversion in power-monitoring circuits, low-level sensor amplification, bridge-transducer signal conditioning, laboratory instrumentation, and analog measurement systems. In these applications, the 4 pA input bias current minimizes disturbance of high-impedance sources, while the zero-drift characteristic supports accurate operation where signal levels remain small relative to system offsets. The device can also serve as a stable gain stage in higher-level analog chains.
When designing around the ICL7653CPA, verify the complete pin assignment and supply limits against the manufacturer datasheet before laying out the PCB. Pay particular attention to bypassing, input common-mode range, output swing, noise bandwidth, and the behavior of the chopper system near the lower end of the useful frequency range. A stable reference-quality implementation requires appropriate layout and decoupling rather than relying on nominal specifications alone.
This product page combines the ICL7653CPA electrical characteristics, package details, sourcing information, and application guidance in one engineering-focused reference. It also identifies compatible same-family alternatives, highlights their qualification differences, and organizes design considerations for instrumentation, current sensing, and low-level analog signal-processing systems.
Pilihan pengganti yang segera untuk ICL7653CPA — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
ICL7653EPA
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
ICL7650CPA
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
ICL7650EPA
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
ICL7651CPA
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
ICL7651EPA
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
ICL7653CPA Penilaian maksimum & Ciri-ciri Elektrik
| Amplifier Type | Chopper (Zero-Drift) |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 2 MHz |
| Slew Rate | 2.5 V/us |
| Input Bias Current | 4 pA |
| Tegangan Pemberi Arus | ±8 V |
| Arus Pemberi Arus | 1.2 mA |
| Gambaran Suhu Operasi | 0°C to +70°C |
| Kemasan | 8-pin PDIP |
| Jenis Pemasangan | Through-hole |
| Package Width | 0.300 in (7.62 mm) |
| Jenis Output | Current output |
| Product Status | Active |
| Series | ICL7653C |
Panduan Konfigurasi Pin ICL7653CPA 0.300 in (7.62 mm)
Konfigurasi pin untuk ICL7653CPA (0.300 in (7.62 mm) pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk ICL7653CPA.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
ICL7653CPA patut untuk 6 aplikasis: Precision Current Measurement, High-Impedance Sensor Interface, Bridge Transducer Conditioning, Laboratory Instrumentation, Low-Level Analog Signal Conditioning, Battery-Powered Measurement.
Precision Current Measurement
The ICL7653CPA is well suited to current-to-voltage conversion because its chopper-stabilized architecture reduces low-frequency offset error while its 4 pA input bias current limits disturbance of high-impedance current signals. A typical circuit uses the amplifier in an inverting configuration around a precision shunt or current-sense resistor. The 2 MHz gain-bandwidth product supports bandwidth beyond slow DC measurement, while the 2.5 V/us slew rate handles faster transients. Check output swing, common-mode limits, and shunt power dissipation at the intended current.
Disebarkan
High-Impedance Sensor Interface
The 4 pA input bias current of the ICL7653CPA makes it useful for low-level sensors whose output impedance is high enough that amplifier input current could create an unacceptable error voltage. The device can amplify a sensor output close to ground while its chopper stabilization improves DC accuracy. Its 2 MHz gain-bandwidth product is ample for many temperature, pressure, strain, and chemical-sensor channels, although the input bias contribution should be checked against the sensor impedance and the complete frequency range of the measured signal.
Disebarkan
Bridge Transducer Conditioning
The ICL7653CPA can provide low-offset gain for strain-gauge, load-cell, pressure-bridge, and similar differential transducers. Chopper stabilization is valuable because the useful bridge signal can be small and slow, conditions under which input offset and drift dominate the measurement. The 4 pA input bias current reduces excitation-rail loading, and the 2 MHz gain-bandwidth product permits moderate-bandwidth filtering after amplification. The circuit must still respect the bridge excitation voltage, input common-mode range, and the amplifier's output-swing limits.
Disebarkan
Laboratory Instrumentation
For laboratory and test instrumentation, the ICL7653CPA combines low input bias current, low-offset behavior, and a 2 MHz gain-bandwidth product in a through-hole 8-pin PDIP package. It can form the gain stage of a buffered front end, a precision reference buffer, or a low-level measurement channel. The package is particularly convenient for prototypes, educational platforms, and repairable laboratory equipment. Designers should include input and output bypassing, use short feedback paths, and verify the chopper-related output noise in the required measurement bandwidth.
Disebarkan
Low-Level Analog Signal Conditioning
The ICL7653CPA is useful when a weak analog signal must be amplified before digitization or comparison. Its chopper-stabilized operation reduces low-frequency error, while the 2 MHz gain-bandwidth product and 2.5 V/us slew rate provide more bandwidth than a purely DC-oriented precision amplifier. In a typical signal-conditioning chain, the device amplifies a sensor or detector output and drives a downstream filter or converter. Select the closed-loop gain according to the manufacturer's stability guidance and confirm that output noise and settling behavior meet the acquisition bandwidth.
Disebarkan
Battery-Powered Measurement
The ICL7653CPA can be used in portable measurement systems where a low-level sensor signal must be amplified before conversion, subject to the device operating from suitable ±8 V or single-supply rails. Its low 4 pA input bias current helps preserve signals from high-impedance sources, and its 1.2 mA supply current helps limit continuous power demand. The 8-pin PDIP package supports through-hole assembly where it is appropriate. A battery design must provide proper rail generation and decoupling while preserving the required input and output common-mode ranges.
Disebarkan
Data referensi kejuruteraan untuk ICL7653CPA — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | ICL7653EPA | ICL7650CPA | ICL7650EPA | ICL7651CPA | ICL7651EPA |
|---|---|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Amplifier Type | Chopper (Zero-Drift) | Chopper (Zero-Drift) | Chopper (Zero-Drift) | Chopper (Zero-Drift) | Chopper (Zero-Drift) | Chopper (Zero-Drift) |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Operating Temperature Range | 0°C to +70°C | Extended-temperature grade | 0°C to +70°C | Extended-temperature grade | 0°C to +70°C | Extended-temperature grade |
Penyeberangsung Jelas
- Commercial-temperature grade with extended-temperature family alternatives (vsICL7653EPA)
- Single-circuit zero-drift amplifier with very low input bias current (vsICL7650CPA)
- Useful speed for precision analog amplification (vsICL7651CPA)
Catatan Desain
Place the input and output bypass capacitors directly beside their associated power pins, and keep feedback resistors and signal traces short. The ICL7653CPA has a 4 pA input bias current, so leakage from long PCB traces, contaminated connectors, or nearby switching nodes can become more important than resistor noise in a high-impedance design.
Do not assume that every ICL765x member can use the same feedback topology. The ICL7653 is intended for unity-gain or higher closed-loop operation, while ICL7650-family devices support different internal-feedback configurations. Reusing a PCB across family members therefore requires checking the complete pin description and stability guidance, not only the PDIP outline.
Evaluate noise at the bandwidth required by the final signal chain rather than using only the amplifier's headline noise figure. Chopper stabilization improves low-frequency offset performance but introduces characteristic narrowband and wideband noise components. A 2 MHz gain-bandwidth product and 2.5 V/us slew rate provide response capability, but filtering and grounding still determine the usable low-level measurement result.
Maklumat Kesediaan
The part is an active commercial-temperature instrumentation amplifier; no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified.