ICS525R-02 - 250MHz Configurable Clock Generator | Renesas
MPN: ICS525R-02 ✓ AktifICS525R-02 Ringkasan
A configurable clock generator is a timing IC that combines a phase-locked loop, programmable frequency synthesis, and output distribution. In the product hierarchy, it belongs to clock and timing ICs and provides a bridge between a stable crystal or external reference and multiple clock domains. The OSCaR family is specifically designed to replace conventional crystal-oscillator arrangements in systems that need programmable frequency selection rather than one fixed output frequency.
The ICS525R-02 supports a maximum output frequency of 250 MHz and includes PLL bypass functionality. Its user-configurable architecture permits engineers to select operating combinations of the voltage-controlled oscillator, reference frequency, and output dividers. The 28-pin SSOP has a 0.154-inch, 3.90 mm body width and integrates clock generation, fanout distribution, and programmable divider resources into one package.
The PLL-based architecture provides a practical alternative to designing a fixed-frequency oscillator and separate divider or buffer networks. Bypass operation allows the device to be evaluated and integrated with an external clock path, while PLL operation supports synthesized outputs from a crystal or clock source. Exact divider ratios, VCO limits, jitter, output levels, and recommended crystal parameters should be selected using the configuration tables in the manufacturer datasheet.
Typical uses include network-interface clock distribution, processor and FPGA clock trees, telecommunications timing, digital test equipment, and industrial control systems. The device is especially useful where several logic domains must be related to one frequency reference but cannot all use a simple fixed crystal oscillator. Short traces, terminated clock routing, and careful separation from high-speed data paths remain essential at the upper operating frequency.
For implementation, evaluate every possible VCO, reference, and output-divider combination before committing to the PCB. Confirm the selected output frequency, duty-cycle tolerance, jitter requirement, crystal load capacitance, and I/O voltage against the manufacturer configuration guide. The SSOP footprint also requires assembly planning for its 0.154-inch body width and adequate lead-clearance spacing.
This product record combines the device function, verified 250 MHz operating point, package information, configuration guidance, and practical replacement considerations. It is intended to help engineers identify whether the ICS525R-02 matches the required clock architecture before moving to a detailed design review.
Pilihan pengganti yang segera untuk ICS525R-02 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera ICS525R-02 (sama faktor bentuk dan kaki) — berbeza dalam Device Type, Package Body Width.
ICS525R-01
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
ICS525R-03
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
ICS525R-11
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →ICS525R-12
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
ICS525R-02 Spesifikasi
| Device Type | Clock generator and fanout distribution IC |
| Product Family | OSCaR user-configurable clock |
| Maximum Output Frequency | 250 MHz |
| Bilangan Output | 1 |
| PLL | Yes, with bypass |
| Input Sources | Clock or crystal |
| Jenis Output | CMOS |
| Kemasan | 28-pin SSOP |
| Package Body Width | 3.90 mm (0.154 inch) |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin ICS525R-02 3.90 mm (0.154 inch)
Konfigurasi pin untuk ICS525R-02 (3.90 mm (0.154 inch) pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk ICS525R-02.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
ICS525R-02 patut untuk 6 aplikasis: FPGA Clock Distribution, Network Interface Timing, Telecommunications Clock Tree, Digital Test and Measurement, Industrial Control Systems, High-Speed Data Conversion.
FPGA Clock Distribution
The ICS525R-02 fits FPGA designs that require one programmable reference to support several related clock domains. Its PLL-based architecture, configurable VCO path, output-divider selections, and 250 MHz maximum output provide flexibility beyond a fixed crystal oscillator. The device can be placed near the FPGA clock input so the reference and distributed clock experience controlled PCB routing. Designers must select a valid reference, VCO, and divider combination, then verify the resulting frequency against the FPGA clock specification. Output jitter, duty-cycle tolerance, I/O voltage, and maximum operating frequency should be checked for the selected clock role before release to layout.
Disebarkan
Network Interface Timing
The ICS525R-02 is appropriate for network-interface timing where a stable reference must be converted into a selectable high-speed clock. Its 250 MHz maximum output provides headroom for Ethernet, serial-interface, and data-conversion clock trees, while the programmable architecture permits different operating modes to share one clock-generation design. The implementation should keep the crystal or reference path short, use the manufacturer-recommended load network, and route the clock as a controlled transmission line when edge rates are high. Confirm the selected output frequency, jitter requirement, supply level, and fanout loading before assigning outputs to multiple communication blocks.
Disebarkan
Telecommunications Clock Tree
The ICS525R-02 supports telecommunications systems that need selectable clock outputs derived from one reference. The PLL, fanout distribution, and programmable divider resources allow clock frequencies to be adapted across line-card operating modes without moving to a separate fixed oscillator for every frequency. At 250 MHz maximum output, PCB signal-integrity practices become important: use a continuous reference plane, avoid splits beneath the device, control clock trace impedance, and minimize stubbing. The final frequency plan must be checked against the permitted VCO and divider ranges, while jitter and duty-cycle requirements should be evaluated for the specific interface clock.
Disebarkan
Digital Test and Measurement
The ICS525R-02 can support test and measurement equipment that synthesizes selectable timing signals from a crystal reference. Its programmable clock architecture is useful when the same instrument must exercise several bus rates, ADC clocks, or ADC/DAC sampling interfaces. The 28-pin SSOP integrates generation and distribution, allowing reference, feedback, programming, and output routing to be planned in one controlled area. Engineers should calculate every divider relationship before schematic capture, use the documented reference configuration, and verify jitter at the output rather than inferring it solely from the 250 MHz maximum frequency. Probe loading and cable-driver behavior should also be considered.
Disebarkan
Industrial Control Systems
The ICS525R-02 fits industrial control systems requiring programmable clock generation for processors, data converters, and communication transceivers. A single reference can support several operating frequencies, reducing the number of discrete oscillator and divider blocks when the system architecture allows it. The device should be positioned near the reference source and sensitive digital loads, with a solid ground plane and short feedback routing. Industrial designs must confirm operating-temperature limits, supply tolerances, and output timing margins before production. The manufacturer configuration tables should be used to ensure every synthesized frequency remains valid under startup, reset, and temperature extremes.
Disebarkan
High-Speed Data Conversion
The ICS525R-02 can generate clocks for high-speed ADC and DAC subsystems when those converters require a programmable sampling frequency derived from a stable source. The PLL and selectable divider paths support clock planning across multiple conversion rates, while the 250 MHz maximum output covers high-speed conversion-clock requirements. Place the generator near the converter clock inputs, maintain short return paths, and use matched routing for differential or complementary clock arrangements. Before implementation, verify output standard, voltage, jitter, duty-cycle distortion, and valid divider combinations. The clock should also be considered when evaluating converter aperture timing and system synchronization.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk ICS525R-02 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | ICS525R-01 | ICS525R-03 | ICS525R-11 | ICS525R-12 |
|---|---|---|---|---|---|
| Package | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Maximum Output Frequency | 250 MHz | 200 MHz | 250 MHz | 250 MHz | 250 MHz |
| Device Type | Clock generator and fanout distribution IC | Configurable clock | PECL-input configurable clock | Configurable clock | Configurable clock |
| Input Configuration | Clock or crystal input | Clock or crystal input | PECL input | Clock or crystal input | Clock or crystal input |
| Output Divider Set | 525-02 divider configuration | 525-01 divider configuration | 525-03 divider configuration | 525-11 divider configuration | 525-12 divider configuration |
| Body Width | 3.90 mm (0.154 inch) | 3.90 mm (0.154 inch) | 3.90 mm (0.154 inch) | 3.90 mm (0.154 inch) | 3.90 mm (0.154 inch) |
Penyeberangsung Jelas
- Higher maximum output frequency than the original 525-01 configuration (vsICS525R-01)
- Dedicated 525-02 output-divider configuration (vsICS525R-01)
- Configurable clock-and-crystal input arrangement (vsICS525R-03)
Catatan Desain
Place the ICS525R-02 close to the crystal or reference-clock source, and route the reference, feedback, and configuration paths away from high-speed clock outputs. Use a continuous ground plane beneath the SSOP and avoid plane splits under the device. At frequencies approaching the 250 MHz maximum, use controlled-impedance clock routing, minimize stubs and test pads, and provide matching termination appropriate to the output topology. The pin assignments and reference schematic should be copied from the manufacturer datasheet rather than inferred from family order codes.
Choose the VCO, reference, and output-divider combination from the manufacturer configuration table before laying out the board. A nominal 250 MHz design goal is not valid unless the selected combination remains within the permitted ranges. Verify output jitter, duty-cycle distortion, rise and fall time, and load capability for the actual frequency. When distributing the clock to multiple loads, include receiver input capacitance and trace loading in the timing budget, and add source-series damping only where the complete clock network supports it.
Do not treat ICS525R-02I, ICS525R-02T, or similar suffix variants as identical order codes without checking temperature, packing, and purchasing requirements. Also avoid assuming that all 525-family members share the same divider table: the manufacturer explicitly distinguishes the 525-01 and 525-02 configurations. Before schematic release, confirm the crystal frequency and load capacitance, PLL mode or bypass state, programmed divider path, supply voltage, and every unused pin according to the device pin-description table.
Maklumat Kesediaan
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for the exact ICS525R-02 ordering information. AEC-Q100 status is not applicable because this is a clock and timing IC rather than an automotive-qualified device.