Renesas Electronics

ICS553MIT - 1:4 200MHz Low-Skew Clock Buffer | Renesas

MPN: ICS553MIT ✓ Aktif
2.375 V to 5.25 V Vdss 8-SOIC Package 200 MHz Speed
MOQ: 1 |

ICS553MIT Ringkasan

Renesas Electronics ICS553MIT is a low-skew clock fanout buffer that distributes one CMOS input clock to four CMOS outputs. It operates from a 2.375 V to 5.25 V supply and supports clock frequencies up to 200 MHz. The device is packaged in an 8-pin SOIC measuring 0.154 inches, or 3.90 mm, in width and belongs to the ICS ClockBlocks family.

A clock fanout buffer is a clock-and-timing integrated circuit that regenerates and distributes one incoming clock signal across multiple outputs. Its place in the hierarchy is clock buffer, then clock distribution device, then clock-and-timing IC, and finally semiconductor. Fanout buffers are used where a source clock must drive several destinations while limiting loading, propagation variation, and signal degradation across a larger system.

The ICS553MIT is identified as a low-skew, 1-to-4 clock buffer. Its four-output arrangement gives a processor, memory interface, communications circuit, or test instrument multiple usable clock outputs from one source. Operation up to 200 MHz makes it applicable to clock trees operating below that maximum frequency, while its 2.375 V to 5.25 V supply range supports common low-voltage digital systems.

The CMOS input and CMOS outputs place the device in the logic and clock-and-timing categories. CMOS interfaces are suitable for modern digital systems because they support rail-to-rail operation in many designs and combine useful noise and power characteristics. Exact propagation delay, output-to-output skew, input-output skew, rise time, fall time, and current-consumption figures should be taken from the manufacturer datasheet before setting timing margins.

Typical uses include distributing a reference clock among four digital loads, buffering a source oscillator before it reaches multiple logic blocks, and supporting compact communications, control, or instrumentation equipment. In each case, trace lengths should be arranged so that all four destinations receive clocks within the timing budget established for the system.

The primary design consideration is timing margin across all four outputs rather than only the source-to-output path. Keep the input and output connections short, maintain a consistent return path, and place decoupling close to the supply pins. Account for the difference between edge arrival at the input and edge arrival at each load when defining setup and hold requirements.

This product page combines the manufacturer part characteristics, source availability, pin-compatible alternatives, comparison criteria, and practical clock-distribution guidance. It is intended to accelerate component identification while keeping the final timing, layout, and qualification decisions with the system designer.

Pilihan pengganti yang segera untuk ICS553MIT — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

553MLF

✅ Masuk Drop-In
📦 8-SOIC
Same ICS553 1:4 low-skew clock-buffer function and 200 MHz class; ordering suffix and qualification details must be checked against the datasheet

📋 Alternatif rujukan (tidak dalam katalog)

NB3L553DR2G

✅ Masuk Drop-In
📦 8-SOIC
Both provide a 1:4 low-skew CMOS clock fanout, but enable behavior, timing values, supply limits, and logic thresholds require verification

📋 Alternatif rujukan (tidak dalam katalog)

ICS553MIT Spesifikasi

Product Type Clock Fanout Buffer (Distribution) IC
Fanout Ratio 1:4
Frekuensi Klock Maksimum 200 MHz
Supply Voltage Range 2.375 V to 5.25 V
Input Logic Type CMOS
Output Logic Type CMOS
Package Type 8-SOIC
Package Width 0.154 in (3.90 mm)
Jenis Pemasangan Surface mount
Device Family ICS ClockBlocks
Skew Characteristics Low-skew
Status RoHS Non-compliant

Panduan Konfigurasi Pin ICS553MIT 0.154 in (3.90 mm)

Konfigurasi pin untuk ICS553MIT (0.154 in (3.90 mm) pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 0.154 in (3.90 mm) untuk ICS553MIT

Tiada data garisan pin yang diperoleh untuk ICS553MIT.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

ICS553MIT patut untuk 6 aplikasis: Digital Processor Clock Distribution, Communications Equipment Clock Tree, Oscillator and Crystal Reference Buffering, Industrial Control and Automation Logic, Test and Measurement Equipment, Data Converter and Memory Interface Clocks.

🖥️

Digital Processor Clock Distribution

ICS553MIT is suitable for distributing one system clock to four digital destinations when the design must remain within a 200 MHz maximum frequency. Place the buffer close to the clock source so the single input sees a clean edge, then route each regenerated output to a separate logic block. Its four-output CMOS architecture avoids asking the source to drive four loads directly. Because this is a low-skew device, evaluate the combined output-to-output skew, propagation delay, trace length, and receiver setup-and-hold requirements. The 2.375 V to 5.25 V operating range also supports common low-voltage digital rails.

🌐

Communications Equipment Clock Tree

In communications equipment, a single reference clock often must reach several serializers, transceivers, or digital controllers. ICS553MIT provides a 1:4 fanout function, allowing one clock source to feed four separate destinations while reducing source loading. Its maximum specified frequency of 200 MHz covers many moderate-speed digital interfaces. The designer should match trace geometry among the four branches where practical and include output-to-output skew in the downstream timing budget. The CMOS input and outputs align with common low-voltage digital logic, while the 2.375 V to 5.25 V supply range supports multiple rail options.

⚡

Oscillator and Crystal Reference Buffering

ICS553MIT can buffer an oscillator or crystal-derived reference clock before it reaches four destination circuits. Regenerating the signal at the buffer provides a controlled fanout point rather than connecting several loads directly to a sensitive oscillator output. The 1:4 topology is useful where a processor, memory interface, converter, and communication block require the same reference. Keep the oscillator-to-buffer path short and provide a continuous ground plane to reduce susceptibility to noise. Check the buffer's input thresholds and timing characteristics against the oscillator amplitude and edge rate before committing the circuit, especially when operating near the 200 MHz frequency limit.

🏭

Industrial Control and Automation Logic

Industrial control assemblies often distribute a common timing or synchronization signal among control, interface, and monitoring blocks. ICS553MIT offers four CMOS clock outputs from one input, simplifying fanout without requiring multiple unrelated buffers. Its 2.375 V to 5.25 V supply range suits many embedded control systems. The critical design task is preserving timing correlation at all four receivers, particularly when loads are separated by different PCB trace lengths or cable delays. Use the datasheet's propagation and skew limits to establish the system budget, and verify the operating-temperature grade required by the equipment before production release.

🔧

Test and Measurement Equipment

ICS553MIT can distribute a reference clock to four acquisition, conversion, or triggering sections of compact test equipment. The one-input, four-output arrangement helps each subsystem receive a regenerated clock while keeping the source connection simple. A maximum frequency of 200 MHz makes the device relevant for moderate-speed digital instrumentation and automated test systems. Engineers should account for clock-to-clock correlation, loading, and receiver timing margin at every output rather than evaluating only the source edge. The 8-SOIC package also supports conventional surface-mount assembly, although the exposed thermal behavior and temperature grade must be checked for the enclosure environment.

🧩

Data Converter and Memory Interface Clocks

ICS553MIT is applicable where a memory controller, data converter, and related digital logic need separate copies of one interface clock. Buffering the source reduces fanout burden and provides four regenerated outputs, while the low-skew design supports timing-sensitive systems. The buffer must operate below 200 MHz and remain within its 2.375 V to 5.25 V supply range. Match output rise and fall characteristics to the receiving devices and review the converter or memory interface's required clock duty cycle, jitter, and setup-and-hold limits. PCB branches should use consistent geometry and an uninterrupted return path to prevent one output from carrying substantially more noise or edge distortion than the others.

Ringkasan Produk Disebarkan

553MLF Same-family 1:4 clock-buffer candidate Dipergunakan di: Digital Processor Clock Distribution, Communications Equipment Clock Tree, Oscillator and Crystal Reference Buffering, Industrial Control and Automation Logic, Test and Measurement Equipment, Data Converter and Memory Interface Clocks NB3L553DR2G 1:4 low-skew fanout-buffer candidate Dipergunakan di: Digital Processor Clock Distribution, Communications Equipment Clock Tree, Oscillator and Crystal Reference Buffering, Industrial Control and Automation Logic, Test and Measurement Equipment, Data Converter and Memory Interface Clocks
What is ICS553MIT?
ICS553MIT is a Renesas Electronics low-skew clock fanout buffer with one CMOS input and four CMOS outputs. According to the manufacturer datasheet, it is part of the ICS ClockBlocks family, supports operation up to 200 MHz, and uses a 2.375 V to 5.25 V supply. It is intended for distributing one clock source across four destinations in digital systems.
What are the key specifications of ICS553MIT that engineers should know?
The key ICS553MIT specifications are a 1:4 fanout ratio, 200 MHz maximum clock frequency, CMOS input and outputs, and a 2.375 V to 5.25 V supply range. The Renesas manufacturer datasheet identifies the device as a low-skew clock buffer in an 8-SOIC package. Timing margins should also be based on its specified propagation delay and skew characteristics.
Where can I download the ICS553MIT datasheet PDF?
The official ICS553MIT datasheet is available from Renesas Electronics through the manufacturer document page for the 553 family. The document contains the clock-buffer characteristics, operating conditions, timing information, package details, and pin assignments. Use that document for design calculations rather than relying on a distributor summary or a third-party document mirror.
Where can I find the ICS553MIT pinout?
The ICS553MIT pin assignment is shown in the pin-configuration section of the Renesas Electronics 553 family datasheet. The device uses an 8-SOIC package. Confirm the input, four outputs, supply, ground, and control-pin assignments against the package drawing before assigning PCB tracks or connecting a replacement.
What is the supply voltage range of ICS553MIT?
The ICS553MIT operates from 2.375 V to 5.25 V. This range comes from the Renesas Electronics manufacturer datasheet and allows the clock buffer to operate in common low-voltage CMOS systems. The connected source and receivers must use compatible logic levels, and the power rails must remain within the stated operating limits.
What is the maximum frequency of ICS553MIT?
The maximum clock frequency of ICS553MIT is 200 MHz. The Renesas Electronics manufacturer datasheet identifies the ICS553 as a 1-to-4 low-skew clock buffer, while the product listing confirms the 200 MHz maximum frequency. This is the maximum specified operating frequency, not a guarantee that every voltage, temperature, and load combination meets a given timing margin.
Where can I buy ICS553MIT online?
Use the Request a Quote form on this page to request ICS553MIT availability, lead time, and a current quotation for the exact 8-SOIC ordering code. The listing identifies the component as an 8-SOIC device, so confirm that the quoted suffix corresponds to the required package and shipment configuration before releasing an order.
What is the price of ICS553MIT?
A current ICS553MIT quotation is available through the Request a Quote form on this page. The form is the appropriate channel for unit pricing, quantity breaks, sourcing questions, and lead-time confirmation because component pricing changes with quantity, availability, package suffix, and market conditions. Submit the target quantity and required shipment form for a precise response.
What is the lead time for ICS553MIT?
Request the current ICS553MIT lead time through the Request a Quote form on this page. Lead time can vary with the exact ordering suffix, requested quantity, and available inventory, so the form should be completed with the required package form, quantity, destination, and target delivery date. This avoids relying on an outdated generic availability statement.
Is ICS553MIT in stock?
ICS553MIT availability should be confirmed through the Request a Quote form on this page. One distributor listing describes the part as available for immediate shipment, but stock changes by quantity and ordering code. Provide the exact suffix and required quantity so the response reflects the current purchasing position rather than a generic listing status.
ICS553MIT vs 553MLF - which is better for a 1:4 clock buffer?
ICS553MIT and 553MLF both belong to the ICS553 low-skew 1-to-4 clock-buffer family and use the same functional arrangement of one input and four outputs. The decision depends on the exact ordering suffix, package form, temperature grade, and production requirements. Compare the manufacturer datasheet ordering information and the required shipment format before treating either MPN as an interchangeable selection.
Can NB3L553DR2G replace ICS553MIT?
NB3L553DR2G can be considered a candidate replacement because it is also described as a low-skew 1-to-4 clock fanout buffer with an 8-SOIC-class footprint. It is not an automatic drop-in choice: verify enable behavior, supply range, propagation delay, output skew, input thresholds, and every pin function against the ICS553MIT datasheet before production use.
When should I choose ICS553MIT over a generic clock buffer?
Choose ICS553MIT when the design needs a documented 1-to-4 CMOS clock-distribution function, operation up to 200 MHz, and a 2.375 V to 5.25 V supply range in an 8-SOIC package. A generic buffer is preferable only if it offers a verified timing, power, enable, or qualification advantage that outweighs the benefit of using the established ICS553 family.
Is ICS553MIT suitable for distributing a 200 MHz system clock?
ICS553MIT is rated for clock frequencies up to 200 MHz, but suitability at the upper limit depends on the actual clock edge rate, load, supply voltage, temperature, and downstream timing requirements. According to the Renesas Electronics manufacturer datasheet, evaluate propagation delay and skew across the complete clock path and preserve sufficient setup and hold margin at every receiver.
What can replace ICS553MIT?
The documented candidates for review are 553MLF and NB3L553DR2G, both associated with low-skew 1-to-4 clock-buffer functions. A valid replacement must match the 8-SOIC footprint, pin functions, supply range, logic thresholds, timing behavior, and output-enable requirements. Treat the candidate as a drop-in option only after checking every pin and timing parameter.
How should ICS553MIT be used in a four-load clock tree?
Connect the source clock to the single input and route the four regenerated outputs to separate destinations. Keep traces short, use a continuous ground reference, and match output loading to the manufacturer limits. The key design task is balancing trace lengths and accounting for output-to-output skew so every receiving circuit receives its clock within its timing window.

Data referensi kejuruteraan untuk ICS553MIT — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose ICS553MIT for a compact four-output CMOS clock tree that requires a Renesas ICS553-family device, a maximum operating frequency of 200 MHz, and a 2.375 V to 5.25 V supply. Select 553MLF when its ordering suffix, qualification grade, shipment form, or lifecycle conditions better match the production requirements while retaining the same 1:4 low-skew function. Consider NB3L553DR2G when its output-enable function, electrical limits, timing characteristics, or sourcing conditions provide a system-level advantage. A candidate is not a drop-in selection until its pin functions, logic thresholds, propagation delay, skew, enable polarity, supply range, and temperature grade have been checked against ICS553MIT.

Perbandingan dengan Gantian

Parametr Produk Ini 553MLF NB3L553DR2G
Package 8-SOIC 8-SOIC 8-SOIC
Brand Renesas Electronics Renesas Electronics onsemi
Product Type Clock Fanout Buffer (Distribution) IC Low-skew 1-to-4 clock buffer Low-skew 1-to-4 clock fanout buffer
Fanout Ratio 1:4 1:4 1:4
Input Logic CMOS CMOS CMOS
Output Logic CMOS CMOS CMOS
Skew Class Low-skew Low-skew Low-skew

Penyeberangsung Jelas

  • Established Renesas ICS553 family positioning (vsNB3L553DR2G)
  • Same-family option can simplify ordering review (vs553MLF)
  • Four-output regeneration in a compact package (vsNB3L553DR2G)

Catatan Desain

Treat all four outputs as part of one timing channel. Compare propagation delay and output-to-output skew at the operating voltage and temperature, then include receiver setup and hold requirements in the clock budget. Keep branches electrically similar where practical, but prioritize the datasheet's skew limit over merely equalizing physical length when return paths or loading differ.

Place the ICS553MIT close to the clock source and route each output directly toward its destination. Use a continuous ground reference, avoid crossing noisy return paths, and minimize stubs and test-point capacitance. A short input route helps the source drive the buffer cleanly, while short output routes reduce trace loss and sensitivity to nearby switching nodes.

Do not assume that every 1-to-4 8-SOIC clock buffer is interchangeable. Before fitting NB3L553DR2G or another candidate, verify input thresholds, output-enable polarity, supply limits, pin assignments, propagation delay, and skew. Also confirm the exact operating-temperature grade and ordering suffix required by the production design.

Decouple the supply close to the device with the capacitance recommended by the manufacturer datasheet and maintain a low-impedance return path. Keep switching-converter and digital-clock traces away from the clock input. The available clock-buffer operating range extends from 2.375 V to 5.25 V, but the supply must remain stable across process, temperature, and load conditions.

Maklumat Kesediaan

RoHS
Non Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The ICS553MIT product listing identifies the component as RoHS non-compliant. No qualification or material-compliance claims beyond that statement were established.

Data disahkan pada: 2026-11-11 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

ICS553MIT datasheet ICS553MIT pinout ICS553MIT datasheet pdf ICS553MIT specifications ICS553MIT 200MHz clock buffer ICS553MIT 8-SOIC pinout ICS553MIT equivalent ICS553MIT replacement ICS553MIT vs NB3L553DR2G ICS553MIT clock distribution ICS553MIT price ICS553MIT stock Renesas ICS553MIT ICS553MIT footprint ICS553MIT application circuit

Komponen dan Tanda berkaitan

Renesas Electronics ICS553MIT ICS553 553MLF NB3L553DR2G onsemi clock fanout buffer clock buffer clock distribution device clock-and-timing IC semiconductor low-skew clock buffer 1:4 fanout CMOS 200 MHz 2.375 V to 5.25 V 8-SOIC SOIC family surface mount SMD output-to-output skew propagation delay output enable ICS ClockBlocks
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ