Renesas Electronics

ICS570AIT - 170MHz Zero-Delay Clock Buffer | Renesas

MPN: ICS570AIT ✓ Aktif
5 V Vdss 8-pin SOIC, 3.90 mm body width Package 170 MHz Speed
MOQ: 1 |

ICS570AIT Ringkasan

Renesas ICS570AIT is a 170 MHz PLL-based zero-delay buffer (ZDB) and fanout clock distributor packaged in an 8-pin SOIC. The A-version is intended for 5 V designs, providing four non-inverted CMOS clock outputs with low-delay clock distribution and programmable spread-spectrum operation. Its clock-buffer architecture integrates analog and digital phase-locked-loop techniques to synchronize multiple system clock domains.

A zero-delay buffer is a clock-management IC that reproduces an input clock at its outputs while compensating for internal propagation delay through a phase-locked loop. Positioned within the hierarchy of clock and timing ICs, a ZDB complements ordinary clock buffers by allowing a system to obtain several low-skew copies of a reference clock. Fanout distribution expands one source into multiple synchronized loads for processors, memory interfaces, communications equipment, and embedded control systems.

The ICS570AIT supports clock frequencies up to 170 MHz and includes spread-spectrum clock generation for reducing narrowband EMI emissions in sensitive equipment. Its four CMOS outputs provide one-to-four fanout capability, while the PLL-based zero-delay architecture supports predictable clock relationships between distributed loads. The 8-pin SOIC package measures approximately 3.90 mm in width and accepts a 0.154-inch lead pitch.

The A-version supply recommendation distinguishes ICS570AIT from the 3.3 V B-version. Designers must therefore verify supply rails, input levels, output loading, and downstream input thresholds before applying the device. Because the part distributes rather than originates the reference clock, input slew rate, return path, and output termination remain important aspects of the implementation.

Typical applications include processor and memory clock distribution, communications-interface clock fanout, embedded system clock trees, and EMI-sensitive digital equipment. Spread-spectrum operation is particularly relevant when the reference clock feeds high-speed digital circuitry and reduced spectral concentration is desirable without eliminating the fundamental clock.

For reliable implementation, use the pin-description table and typical application circuit in the manufacturer datasheet when assigning PCB tracks. Keep the reference clock and output routes short, provide a continuous return plane, and validate timing at the actual device pins because package and trace delay can affect a nominal zero-delay design.

This product reference combines the device architecture, operating limits, package information, sourcing guidance, and design considerations needed to evaluate the ICS570AIT. It also distinguishes verified drop-in alternatives from related clock devices that require different voltage, pinout, output-count, or circuit arrangements.

Pilihan pengganti yang segera untuk ICS570AIT — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Tiada pilihan pengganti yang segera untuk produk ini.

Minta Alternatif

ICS570AIT Spesifikasi

Frekuensi Klock Maksimum 170 MHz
Device Type PLL-based zero-delay buffer and fanout clock distributor
Architecture Proprietary analog/digital phase-locked-loop technique
Output Technology CMOS
Output Count 4 outputs
Inverted Output Count 0 outputs
Recommended Supply Voltage for A Version 5 V
Clock Features Zero-delay buffering, fanout distribution, and spread-spectrum clock generation
Kemasan 8-pin SOIC, 3.90 mm body width
Package Lead Pitch 0.154 inch (3.90 mm)
Jenis Pemasangan Surface-mount

Panduan Konfigurasi Pin ICS570AIT 0.154 inch (3.90 mm)

Konfigurasi pin untuk ICS570AIT (0.154 inch (3.90 mm) pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 0.154 inch (3.90 mm) untuk ICS570AIT

Tiada data garisan pin yang diperoleh untuk ICS570AIT.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

ICS570AIT patut untuk 6 aplikasis: Processor Clock Fanout, Memory Interface Clock Distribution, Communications Equipment Clock Tree, EMI-Sensitive Digital Systems, Embedded Control Clock Fanout, Industrial Control Module Clocking.

🖥️

Processor Clock Fanout

The ICS570AIT fits processor clock-distribution designs that need up to four related CMOS clock outputs from one reference signal. Its PLL-based zero-delay-buffer architecture compensates for internal propagation delay, while the 170 MHz maximum operating frequency provides ample range for many digital processor and controller clock trees. The device is placed between the system oscillator or oscillator buffer and the clock receivers, with short output routes to minimize board-level skew. Its spread-spectrum capability can also reduce narrowband EMI concentration. The principal design check is that the A-version is intended for 5 V operation and that all downstream inputs tolerate the resulting CMOS levels.

🖥️

Memory Interface Clock Distribution

The ICS570AIT is useful when a memory subsystem requires multiple clock destinations derived from one low-skew source. Four non-inverted CMOS outputs allow separate routing to memory devices or interface blocks, and the zero-delay-buffer function compensates for the IC's internal propagation delay. At frequencies up to 170 MHz, the architecture supports demanding digital clock trees, but the engineer must confirm receiver thresholds, load capacitance, and timing margins on the assembled PCB. Short, impedance-controlled routes and a continuous reference plane are important because package and trace delay can exceed the nominal device compensation.

🌐

Communications Equipment Clock Tree

The ICS570AIT can provide clock fanout in communications equipment where several digital subsystems need closely related timing signals. One reference clock is distributed through four CMOS outputs, reducing the number of separate buffering stages and helping maintain consistent phase relationships across the design. The device operates up to 170 MHz and supports spread-spectrum clock generation, which can reduce narrowband EMI in equipment that must meet emission constraints. Deployment should be based on the 5 V A-version supply recommendation, with output loading and receiver bandwidth checked against the manufacturer electrical tables.

🏭

EMI-Sensitive Digital Systems

Spread-spectrum operation makes the ICS570AIT relevant to digital systems in which a fixed-frequency reference could create a concentrated EMI peak. The device distributes the clock to four CMOS outputs while modulating the spectrum to reduce energy at one narrow frequency. It can therefore serve clock trees in industrial controllers, communications modules, and embedded platforms that require deterministic fanout plus improved emissions behavior. The allowable modulation range and any timing effect must be taken from the manufacturer datasheet. Board-level testing remains necessary because cable, connector, and enclosure resonances can influence the final radiated or conducted emissions result.

🧩

Embedded Control Clock Fanout

The ICS570AIT can expand a single oscillator reference into four clock destinations for embedded controllers, serial transceivers, and supporting digital logic. Its zero-delay-buffer function is valuable where several branches must retain predictable relationships, while the 8-pin SOIC package supports compact implementation. The 170 MHz frequency capability accommodates many control, networking, and peripheral clock requirements. Designers should use the official pin diagram, provide a stable reference-clock slew rate, and keep each output route short enough to meet the timing requirements of its receiver.

🏭

Industrial Control Module Clocking

The ICS570AIT is suitable for clock distribution inside industrial control modules that combine processors, memory, communication interfaces, and mixed-signal peripherals. Four CMOS outputs allow one reference to feed several timing domains, while spread-spectrum operation can assist with EMI control in compact equipment. The 5 V A-version supply recommendation fits systems with a compatible 5 V power architecture, but every connected receiver must be checked for valid input levels. Place the buffer near the clock-source branch point and keep sensitive routes away from switching power stages to preserve predictable timing.

What is the ICS570AIT?
The ICS570AIT is a 170 MHz PLL-based zero-delay buffer with four CMOS outputs, packaged in an 8-pin SOIC. According to the Renesas 570 datasheet, it uses proprietary analog/digital phase-locked-loop techniques to distribute a reference clock while compensating for internal clock-buffer delay. The A-version is recommended for 5 V designs, and the device also supports spread-spectrum clock generation for EMI control.
What clock frequency does the ICS570AIT support?
The ICS570AIT supports clocks up to 170 MHz. The DigiKey product listing identifies the device as a 170 MHz fanout distribution, spread-spectrum clock generator, and zero-delay buffer. When using it in a design, verify that the reference clock, supply voltage, output loading, and downstream receiver thresholds remain compatible with the operating conditions stated in the manufacturer datasheet.
What supply voltage should I use with ICS570AIT?
The ICS570AIT A-version is intended for 5 V designs. The Renesas 570 datasheet distinguishes the A-version as the 5 V option and the B-version as the 3.3 V option. Do not substitute a B-version without checking every rail and I/O level, because operating the A-version from an unintended voltage can compromise timing, output behavior, or device reliability.
How many clock outputs does the ICS570AIT provide?
The ICS570AIT provides four non-inverted CMOS outputs. This gives one reference input four fanout destinations while the internal PLL compensates for internal propagation delay. The zero-delay-buffer architecture is useful when several digital loads must receive related clock signals, although final board-level skew still depends on routing, loading, and receiver characteristics.
Where can I download the ICS570AIT datasheet PDF?
Download the ICS570AIT technical documentation from the official Renesas 570 datasheet page at https://www.renesas.com/document/dst/570-datasheet. The document describes the zero-delay-buffer architecture, A- and B-version supply recommendations, 8-pin SOIC package, PLL technique, and application information. Use its pin-description table when assigning tracks and its electrical tables for final design verification.
Where can I find the ICS570AIT pinout?
The ICS570AIT pin assignments are shown in the pin-description table of the official Renesas 570 datasheet. The component uses an 8-pin SOIC package, but connector orientation and internal signal names must be taken directly from that diagram rather than inferred from another PLL or clock-buffer family. Check the pin-1 marker carefully against the PCB footprint before fabrication.
How does spread-spectrum clock generation help the ICS570AIT?
Spread-spectrum operation spreads clock energy across a frequency range, reducing the peak spectral concentration that a fixed-frequency clock can create. The ICS570AIT is identified as a spread-spectrum clock generator in addition to being a zero-delay buffer and fanout distributor. This can help with EMI control, but the permitted modulation range and resulting timing behavior must be taken from the manufacturer datasheet.
What is the difference between the ICS570AIT and the 3.3 V B-version?
The primary documented difference is the recommended supply voltage: the ICS570AIT A-version is intended for 5 V designs, while the B-version is intended for 3.3 V designs. Both belong to the 570 zero-delay-buffer family, but a B-version should not be treated as an automatic drop-in replacement without checking input thresholds, output levels, timing, and system power rails.
Is there a verified drop-in replacement for the ICS570AIT?
No additional drop-in replacement could be verified from the available manufacturer and cross-reference material. The family information confirms that the A and B versions use different recommended supply voltages, while one comparison result explicitly says circuit modification may be required for the candidate device. Use the Request a Quote form on this page for sourcing help, and validate any proposed replacement against pinout, supply voltage, frequency, output count, and timing.
What can replace the ICS570AIT?
The ICS570AIT can only be replaced safely after matching its 8-pin SOIC footprint, 170 MHz operating requirement, 5 V A-version supply design, four CMOS outputs, and zero-delay-buffer function. No verified same-footprint substitute is documented here, so related PLL drivers should not be treated as drop-in parts without schematic and timing verification. Submit the required operating conditions through the Request a Quote form for sourcing support.
When should I choose the ICS570AIT for a clock tree?
Choose the ICS570AIT when one reference clock must feed up to four related CMOS loads at up to 170 MHz and the board uses the A-version's intended 5 V design. Its PLL-based zero-delay architecture is useful for fanout distribution, while spread-spectrum capability can support EMI-sensitive systems. Select another clock device if you need a different supply voltage, output count, differential outputs, or a package other than 8-pin SOIC.
Is ICS570AIT suitable for processor and memory clock distribution?
The ICS570AIT is suitable for processor, memory, and embedded-system clock distribution when its 170 MHz maximum frequency, 5 V supply recommendation, four CMOS outputs, and zero-delay-buffer behavior meet the load requirements. Validate every receiver's input threshold and the worst-case board skew. The device distributes an existing reference clock; it does not replace the oscillator or reference source that establishes the system timing reference.
How should ICS570AIT be placed on the PCB?
Place the ICS570AIT close to the clock source and the loads it serves, while keeping the reference input and output routes short. Follow the package dimensions and pin orientation in the manufacturer datasheet, maintain a continuous ground reference beneath the device, and avoid routing sensitive clock nets next to high-current switching nodes. Validate timing at the receiver pins because trace and package delay affect the achieved skew.
What are the key specifications of ICS570AIT that engineers should know?
The key ICS570AIT specifications are a 170 MHz maximum clock frequency, four non-inverted CMOS outputs, a PLL-based zero-delay-buffer architecture, spread-spectrum clock generation, a 5 V A-version supply recommendation, and an 8-pin SOIC package with a 0.154-inch lead pitch. These figures define its role as a multi-output clock distributor rather than a standalone oscillator.
Where can I buy the ICS570AIT and check current price and lead time?
Use the Request a Quote form on this page to request the current ICS570AIT price, stock position, lead time, and applicable quantity packaging. Pricing and availability can change without notice, so an up-to-date quotation is more reliable than a cached historical figure. Include the required reel or tube packaging, target quantity, delivery location, and production schedule with the request.

Data referensi kejuruteraan untuk ICS570AIT — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the ICS570AIT when the design needs one reference clock distributed to as many as four CMOS loads, requires operation up to 170 MHz, and uses the A-version's intended 5 V supply architecture. Its PLL-based zero-delay function and spread-spectrum capability make it particularly useful for processor, memory, communications, and industrial clock trees. A related 570 B-version is not an automatic replacement because its recommended supply is 3.3 V. The 570AILFT comparison also indicates differing main parameters and possible circuit modification, so it should not be treated as a verified drop-in substitute. Consider another device instead when the design needs differential outputs, a different output count, lower-voltage-only operation, or a package other than 8-pin SOIC. For any replacement, verify the pinout, supply rails, maximum frequency, output timing, spread-spectrum capability, and load compatibility before releasing production artwork.

Perbandingan dengan Gantian

Parametr Produk Ini
Package 8-pin SOIC, 3.90 mm width
Brand Renesas Electronics
Device Function PLL-based zero-delay buffer and fanout distributor
Maximum Clock Frequency 170 MHz
Output Count 4 non-inverted CMOS outputs
Recommended Supply 5 V for A-version
Clock Features Zero-delay buffering, fanout distribution, spread-spectrum clock generation
Architecture Proprietary analog/digital phase-locked-loop technique
Lead Pitch 0.154 inch (3.90 mm)

Penyeberangsung Jelas

  • Combines four-output fanout with zero-delay buffering (vs570AILFT)
  • Designed for 5 V systems (vsICS570 B-version)
  • Includes spread-spectrum clock generation (vs570AILFT)

Catatan Desain

Use the manufacturer's 8-pin SOIC land pattern and confirm pin-1 orientation against the PCB footprint before fabrication. Place the ICS570AIT near the reference-clock source and the loads it serves, and route each clock output directly to its destination where possible. A continuous ground plane beneath the package provides a stable return path and helps limit crosstalk between the four clock outputs.

Treat zero delay as compensation for internal propagation, not as permission for unlimited trace length. Validate timing at the receiver pins with the intended load, PCB stack-up, and clock slope. Keep output traces short, avoid splitting a clock into multiple unmodeled branches, and use the reference termination guidance in the manufacturer application circuit when the board requires controlled impedance.

Use spread-spectrum operation when reducing narrowband clock emissions is beneficial, but verify the approved modulation range and clock-jitter implications in the manufacturer datasheet. Place the device and its reference clock away from high-current switching nodes and keep the ground return path short. Final EMI performance must be measured because enclosure, cable, connector, and board resonances can dominate the result.

Do not treat the 3.3 V B-version as an automatic substitute for the 5 V A-version. Confirm input thresholds, output levels, timing limits, and supply tolerances before using any related 570 device. Also verify the reference-clock slew rate and output loading, because a nominal zero-delay buffer cannot compensate for an unsuitable source waveform or an overloaded output.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

No definitive compliance declaration for the exact ICS570AIT ordering code appears in the retrieved technical summaries. Confirm the current material and environmental declarations with the manufacturer before using the component in a regulated production program.

Data disahkan pada: 2026-11-16 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

ICS570AIT datasheet ICS570AIT pinout ICS570AIT datasheet pdf ICS570AIT 170MHz ICS570AIT zero delay buffer ICS570AIT equivalent ICS570AIT replacement ICS570AIT cross reference ICS570AIT 8-SOIC pinout ICS570AIT spread spectrum clock ICS570AIT price ICS570AIT stock

Komponen dan Tanda berkaitan

Renesas Electronics ICS570AIT 570AILFT ICS570 B-version zero-delay buffer ZDB clock buffer clock and timing IC phase-locked loop PLL spread-spectrum clock generator fanout distribution CMOS 170 MHz 5 V 8-pin SOIC SOIC package family surface-mount package clock skew phase jitter electromagnetic interference EMI processor clock distribution memory interface clock communications clock tree
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ