INA134UA/2K5 - 0 dB Audio Receiver | Texas Instruments
MPN: INA134UA/2K5 ✓ AktifINA134UA/2K5 Ringkasan
An audio differential line receiver is a specialized analog amplifier that converts a small differential signal appearing across two conductors into a single-ended output. The INA134 belongs to the operational-amplifier hierarchy and the broader signal-conditioning category. Its internal precision resistors establish the unity differential gain, while its differential input arrangement rejects common-mode noise that appears equally on both input lines.
The manufacturer specifies low distortion of 0.0005% at 1 kHz and a high slew rate of 14 V/us. These characteristics support accurate reproduction of high-amplitude and rapidly changing audio waveforms. The receiver also provides wide output voltage swing and high output-drive capability for driving downstream audio stages. Typical dual supplies include ±5 V, ±9 V, ±12 V, and ±15 V.
Technically, the INA134 combines high-performance operational amplifiers with on-chip precision resistors. Its differential architecture is intended to suppress signal corruption from shared ground impedance and cable-induced common-mode voltage. A unity gain of 0 dB means the receiver primarily provides buffering and differential-to-single-ended conversion rather than voltage amplification.
Typical uses include balanced audio input receivers, active mixer interfaces, professional audio equipment, consumer audio signal paths, and instrumentation requiring low-distortion differential input handling. The device is especially relevant when a balanced source must feed a conventional single-ended audio circuit while preserving signal integrity.
Designers should observe the specified dual-supply limits, maintain common-mode input voltage within the operating region, and use appropriate bypassing close to the supply pins. Input and output routing should minimize loop area and preserve signal pairing. The 8-pin SOIC footprint also requires adequate thermal copper and assembly clearance where the operating environment is elevated.
Pilihan pengganti yang segera untuk INA134UA/2K5 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera INA134UA/2K5 (sama faktor bentuk dan kaki) — berbeza dalam Number of Channels, Package, Slew Rate.
INA2134UA/2K5
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
INA2134UA
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →INA134UA/2K5 Penilaian maksimum & Ciri-ciri Elektrik
| Device Type | Single audio differential line receiver |
| Number of Channels | 1 channel |
| Differential Gain | 0 dB (G = 1) |
| Minimum Supply Voltage | ±4 V |
| Maximum Supply Voltage | ±18 V |
| Typical Dual Supply Voltages | ±5 V, ±9 V, ±12 V, or ±15 V |
| Total Distortion plus Noise | 0.0005% at 1 kHz |
| Slew Rate | 14 V/us |
| Minimum Operating Temperature | -40°C |
| Maximum Operating Temperature | +85°C |
| Kemasan | 8-pin SOIC (D) |
| Bilangan Pin | 8 pins |
| Jenis Pemasangan | Surface mount |
| Internal Precision Resistors | On-chip |
Panduan Konfigurasi Pin INA134UA/2K5 8-pin soic (d)
Konfigurasi pin untuk INA134UA/2K5 (8-pin soic (d) pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk INA134UA/2K5.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
INA134UA/2K5 patut untuk 6 aplikasis: Balanced Audio Input Receiver, Audio Mixer Interface, Active Speaker Input, Studio Recording Equipment, Consumer Audio Signal Conditioning, Industrial Audio Monitoring.
Balanced Audio Input Receiver
The Texas Instruments INA134UA/2K5 fits a balanced professional-audio input because its 0 dB differential gain converts the pair of input conductors into a single-ended signal without adding substantial voltage gain. Its 0.0005% distortion at 1 kHz and 14 V/us slew rate support accurate handling of music and speech waveforms. Place the receiver between the input connector and the following mixer or voltage-controlled amplifier, and observe the manufacturer’s grounding and reference guidance. The principal benefit is differential signal capture with common-mode rejection; the trade-off is the need for dual supply rails and sufficient input and output headroom.
Disebarkan
Audio Mixer Interface
The INA134UA/2K5 can serve as the input interface of an audio mixer because its unity-gain architecture buffers a differential source before the signal reaches summing and gain-control circuitry. The 14 V/us slew rate provides useful dynamic response for large transients, while the manufacturer-rated 0.0005% distortion at 1 kHz limits added signal nonlinearity. Its differential input arrangement is valuable when the source and mixer grounds are not perfectly isolated. Keep the input network close to the receiver, maintain the differential pair geometry, and verify output swing at the selected ±5 V to ±15 V supply condition.
Disebarkan
Active Speaker Input
The Texas Instruments INA134UA/2K5 is appropriate for an active-speaker input stage when the speaker amplifier accepts a single-ended signal but the upstream source is balanced. The receiver’s 0 dB gain preserves the source level while converting the balanced pair to a conventional output. Its 0.0005% distortion at 1 kHz and 14 V/us slew rate support low-distortion reproduction of abrupt audio peaks. Use the device’s rated output-drive capability and swing limits to confirm compatibility with the next stage, and preserve the manufacturer’s bypass recommendations to prevent supply noise from entering the audio path.
Disebarkan
Studio Recording Equipment
The INA134UA/2K5 suits studio recording equipment requiring a low-distortion balanced receiver, particularly in analog mixer and monitor-control signal chains. Its unity differential gain avoids adding unnecessary amplification ahead of a calibrated gain stage, and its specified 0.0005% distortion at 1 kHz supports transparent signal transfer. The 14 V/us slew rate also helps preserve large transient content. For best performance, keep the balanced input traces closely paired, use a quiet ground strategy, select supply voltages that provide adequate output swing, and check the exact pin assignment and recommended decoupling from the manufacturer datasheet.
Disebarkan
Consumer Audio Signal Conditioning
The INA134UA/2K5 can condition a balanced consumer-audio source before an ADC, codec, or conventional single-ended amplifier. Differential reception reduces susceptibility to common-mode noise encountered in longer cable runs, while unity gain keeps signal amplitude close to the source level. The manufacturer’s 0.0005% distortion figure at 1 kHz and 14 V/us slew rate are useful baseline indicators for audio fidelity and transient handling. The design must still ensure that the source voltage, common-mode range, and required output amplitude remain inside the device’s operating limits.
Disebarkan
Industrial Audio Monitoring
The INA134UA/2K5 is suitable for industrial audio-monitoring equipment that receives a balanced signal from a remote microphone or line source. Its differential input structure helps separate the wanted audio signal from common-mode noise introduced by cables and shared grounds. With 0 dB gain, it can buffer the source before classification, recording, or alarm processing, while the 14 V/us slew rate preserves fast transients. The -40°C to +85°C operating range supports industrial temperature conditions, but enclosure heat, grounding faults, and ESD protection must be addressed separately from the receiver’s signal performance.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk INA134UA/2K5 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | INA2134UA/2K5 | INA2134UA |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC (D) | 8-pin SOIC | 8-pin SOIC |
| Device Type | Single audio differential line receiver | Audio differential line receiver | Audio differential line receiver |
| Differential Gain | 0 dB (G = 1) | 0 dB (G = 1) | 0 dB (G = 1) |
| Operating Temperature | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
| Internal Precision Resistors | Yes | Yes | Yes |
| Orderable Suffix | /2K5 | /2K5 | Base orderable suffix |
Penyeberangsung Jelas
- Published low-distortion performance (vsINA2134UA/2K5)
- Unity-gain differential receiver (vsINA2134UA)
- Industrial temperature coverage (vsINA2134UA/2K5)
- Established INA134 application positioning (vsINA2134UA)
Catatan Desain
Select positive and negative supply rails within the specified ±4 V to ±18 V range, while separately checking output swing and input common-mode limits at the actual signal level. Place the manufacturer-recommended bypass capacitors close to the supply pins and keep return-current paths short. Because the device has a unity gain, headroom is consumed mainly by internal architecture and output swing rather than feedback gain; unused output swing should be retained for transients rather than operating near the rail.
Route the two inputs as a closely coupled differential pair and keep them away from switching nodes and high-current return paths. The receiver’s differential architecture rejects common-mode noise, but imperfect pair geometry can reduce that benefit. Connect the ground and reference network as shown in the manufacturer application guidance, and place input-network components near the receiver pins. Avoid long loops between the source, input pins, and their return path because they can reintroduce pickup that the receiver is intended to reject.
Check the source impedance and bandwidth before finalizing the input network. A 14 V/us slew rate supports fast audio transients, but the complete signal path still depends on the amplifier’s gain-bandwidth response, output loading, and source impedance. Use the manufacturer typical-performance curves and recommended application circuit to select resistor and capacitor values, and test the assembled board for low-frequency channel differences and high-frequency differential-mode pickup.
Do not treat the 0 dB gain as permission to ignore input and output headroom. Verify that the balanced source remains within the input common-mode region and that the single-ended output remains within the specified swing for the selected supplies. A dual-supply receiver also requires correct negative-rail generation and startup sequencing. Check pin names directly in the manufacturer pin table before PCB release, especially when comparing INA134 and INA2134 orderable devices.
Maklumat Kesediaan
The device is identified as an industrial-temperature, 8-pin SOIC audio receiver. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available manufacturer and distributor information. No AEC-Q100 qualification is identified for this exact orderable device.