Texas Instruments

INA134UA/2K5 - 0 dB Audio Receiver | Texas Instruments

Артикул: INA134UA/2K5 ✓ Активен
±4 V Vdss On-chip Rds(on) 8-pin SOIC (D) Package
MOQ: 1 |

INA134UA/2K5 Обзор

Texas Instruments INA134UA/2K5 is a single-channel, unity-gain audio differential line receiver with a gain of 0 dB, a 14 V/us slew rate, and 0.0005% distortion at 1 kHz, housed in an 8-pin SOIC package. It accepts dual power supplies from ±4 V to ±18 V and operates across a -40°C to +85°C temperature range.

An audio differential line receiver is a specialized analog amplifier that converts a small differential signal appearing across two conductors into a single-ended output. The INA134 belongs to the operational-amplifier hierarchy and the broader signal-conditioning category. Its internal precision resistors establish the unity differential gain, while its differential input arrangement rejects common-mode noise that appears equally on both input lines.

The manufacturer specifies low distortion of 0.0005% at 1 kHz and a high slew rate of 14 V/us. These characteristics support accurate reproduction of high-amplitude and rapidly changing audio waveforms. The receiver also provides wide output voltage swing and high output-drive capability for driving downstream audio stages. Typical dual supplies include ±5 V, ±9 V, ±12 V, and ±15 V.

Technically, the INA134 combines high-performance operational amplifiers with on-chip precision resistors. Its differential architecture is intended to suppress signal corruption from shared ground impedance and cable-induced common-mode voltage. A unity gain of 0 dB means the receiver primarily provides buffering and differential-to-single-ended conversion rather than voltage amplification.

Typical uses include balanced audio input receivers, active mixer interfaces, professional audio equipment, consumer audio signal paths, and instrumentation requiring low-distortion differential input handling. The device is especially relevant when a balanced source must feed a conventional single-ended audio circuit while preserving signal integrity.

Designers should observe the specified dual-supply limits, maintain common-mode input voltage within the operating region, and use appropriate bypassing close to the supply pins. Input and output routing should minimize loop area and preserve signal pairing. The 8-pin SOIC footprint also requires adequate thermal copper and assembly clearance where the operating environment is elevated.

Аналоги без доработки для INA134UA/2K5 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с INA134UA/2K5 (тот же форм-фактор и посадочное место) — отличается по Number of Channels, Package, Slew Rate.

Texas Instruments
Number of Channels: 2 channels
Package: 14-pin SOIC
Slew Rate: 14 V/µs

INA2134UA/2K5

✅ Прямая замена
📦 8-pin SOIC
Related TI unity-gain differential receiver with the same 8-pin SOIC format; key distortion and slew-rate values require comparison against the INA134UA/2K5 datasheet

📋 Справочный аналог (нет в каталоге)

INA2134UA

✅ Прямая замена
Texas Instruments
📦 8-pin SOIC
Dual audio differential line receiver · 2 channels · 1 V/V (0 dB) · 0.0005% at 1 kHz · 14 V/µs · ±18 V · 2.9 mA maximum · 90 dB minimum

Уточнить цену

Открыть даташит →

INA134UA/2K5 Максимальные параметры и электрические характеристики

Device Type Single audio differential line receiver
Number of Channels 1 channel
Differential Gain 0 dB (G = 1)
Minimum Supply Voltage ±4 V
Maximum Supply Voltage ±18 V
Typical Dual Supply Voltages ±5 V, ±9 V, ±12 V, or ±15 V
Total Distortion plus Noise 0.0005% at 1 kHz
Slew Rate 14 V/us
Minimum Operating Temperature -40°C
Maximum Operating Temperature +85°C
Корпус 8-pin SOIC (D)
Количество выводов 8 pins
Тип монтажа Surface mount
Internal Precision Resistors On-chip

Руководство по цоколевке INA134UA/2K5 в корпусе 8-pin soic (d)

Цоколевка для INA134UA/2K5 (корпус 8-pin soic (d)). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.

Схема цоколевки корпуса 8-pin soic (d) для INA134UA/2K5

Нет подробных данных о распиновке для INA134UA/2K5.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

INA134UA/2K5 подходит для 6 применениеs: Balanced Audio Input Receiver, Audio Mixer Interface, Active Speaker Input, Studio Recording Equipment, Consumer Audio Signal Conditioning, Industrial Audio Monitoring.

🎧

Balanced Audio Input Receiver

The Texas Instruments INA134UA/2K5 fits a balanced professional-audio input because its 0 dB differential gain converts the pair of input conductors into a single-ended signal without adding substantial voltage gain. Its 0.0005% distortion at 1 kHz and 14 V/us slew rate support accurate handling of music and speech waveforms. Place the receiver between the input connector and the following mixer or voltage-controlled amplifier, and observe the manufacturer’s grounding and reference guidance. The principal benefit is differential signal capture with common-mode rejection; the trade-off is the need for dual supply rails and sufficient input and output headroom.

🎚️

Audio Mixer Interface

The INA134UA/2K5 can serve as the input interface of an audio mixer because its unity-gain architecture buffers a differential source before the signal reaches summing and gain-control circuitry. The 14 V/us slew rate provides useful dynamic response for large transients, while the manufacturer-rated 0.0005% distortion at 1 kHz limits added signal nonlinearity. Its differential input arrangement is valuable when the source and mixer grounds are not perfectly isolated. Keep the input network close to the receiver, maintain the differential pair geometry, and verify output swing at the selected ±5 V to ±15 V supply condition.

🔊

Active Speaker Input

The Texas Instruments INA134UA/2K5 is appropriate for an active-speaker input stage when the speaker amplifier accepts a single-ended signal but the upstream source is balanced. The receiver’s 0 dB gain preserves the source level while converting the balanced pair to a conventional output. Its 0.0005% distortion at 1 kHz and 14 V/us slew rate support low-distortion reproduction of abrupt audio peaks. Use the device’s rated output-drive capability and swing limits to confirm compatibility with the next stage, and preserve the manufacturer’s bypass recommendations to prevent supply noise from entering the audio path.

🎙️

Studio Recording Equipment

The INA134UA/2K5 suits studio recording equipment requiring a low-distortion balanced receiver, particularly in analog mixer and monitor-control signal chains. Its unity differential gain avoids adding unnecessary amplification ahead of a calibrated gain stage, and its specified 0.0005% distortion at 1 kHz supports transparent signal transfer. The 14 V/us slew rate also helps preserve large transient content. For best performance, keep the balanced input traces closely paired, use a quiet ground strategy, select supply voltages that provide adequate output swing, and check the exact pin assignment and recommended decoupling from the manufacturer datasheet.

📱

Consumer Audio Signal Conditioning

The INA134UA/2K5 can condition a balanced consumer-audio source before an ADC, codec, or conventional single-ended amplifier. Differential reception reduces susceptibility to common-mode noise encountered in longer cable runs, while unity gain keeps signal amplitude close to the source level. The manufacturer’s 0.0005% distortion figure at 1 kHz and 14 V/us slew rate are useful baseline indicators for audio fidelity and transient handling. The design must still ensure that the source voltage, common-mode range, and required output amplitude remain inside the device’s operating limits.

🏭

Industrial Audio Monitoring

The INA134UA/2K5 is suitable for industrial audio-monitoring equipment that receives a balanced signal from a remote microphone or line source. Its differential input structure helps separate the wanted audio signal from common-mode noise introduced by cables and shared grounds. With 0 dB gain, it can buffer the source before classification, recording, or alarm processing, while the 14 V/us slew rate preserves fast transients. The -40°C to +85°C operating range supports industrial temperature conditions, but enclosure heat, grounding faults, and ESD protection must be addressed separately from the receiver’s signal performance.

What is the operating voltage of INA134UA/2K5?
The INA134UA/2K5 accepts dual supply voltages from ±4 V to ±18 V, with ±5 V, ±9 V, ±12 V, and ±15 V identified as typical operating points. According to the Texas Instruments INA134 product page and datasheet, the device requires positive and negative supply rails rather than a single-ended supply. This makes it suitable for conventional dual-rail audio systems, although the selected rail voltages must also satisfy the input common-mode and output-swing limits for the intended signal.
What is the gain of INA134UA/2K5?
The INA134UA/2K5 has a differential gain of 0 dB, equivalent to a gain of 1. The manufacturer describes it as a 0 dB audio differential line receiver whose on-chip precision resistors establish the gain. It is intended primarily for balanced-to-single-ended conversion and buffering rather than substantial voltage amplification. The manufacturer identifies INA2134 as a related differential receiver family for designs that may require different device characteristics or availability.
What are the key specifications of INA134UA/2K5 that engineers should know?
The principal INA134UA/2K5 specifications are unity differential gain of 0 dB, 0.0005% distortion at 1 kHz, and a 14 V/us slew rate. It operates from ±4 V to ±18 V across -40°C to +85°C and is offered in an 8-pin SOIC package. According to the Texas Instruments product page, the receiver combines high-performance operational amplifiers with on-chip precision resistors, providing low distortion, wide output swing, and strong output-drive capability for professional and consumer audio.
Where can I download the INA134UA/2K5 datasheet PDF?
The official INA134UA/2K5 technical information is available from the Texas Instruments INA134 product page at https://www.ti.com/product/INA134. That page links the manufacturer datasheet, ordering information, pin information, and parametric data for the INA134UA/2K5 orderable. Use the manufacturer copy as the controlling document for the pin description table, absolute maximum ratings, recommended operating conditions, typical performance curves, and application guidance.
Where can I find the INA134UA/2K5 pinout?
The INA134UA/2K5 uses an 8-pin SOIC package, and its authoritative pin assignment is shown in the Texas Instruments INA134 datasheet. Use the pin-description table when connecting the differential input, output, supply rails, and any documented reference or configuration pins. The ordering result identifies the package as 8-SOIC, while the manufacturer product page specifies the D package with eight pins. The page schematic should not be used as a substitute for the datasheet pin table.
Where can I buy INA134UA/2K5 online?
Use the Request a Quote form on this page to request INA134UA/2K5 availability, quotation, and suitable order quantities. The manufacturer’s orderable-device page confirms that INA134UA/2K5 is an 8-pin SOIC industrial-temperature part. Because commercial conditions and inventory can change, current availability, minimum order quantity, and delivery scheduling should be confirmed through the quotation workflow rather than relying on an outdated catalog snapshot.
What is the price of INA134UA/2K5?
The current commercial price for INA134UA/2K5 is obtained through the Request a Quote form on this page. The structured pricing area on this page can be updated as market and channel conditions change. For engineering review, the important cost factors are the exact manufacturer orderable MPN, its 8-pin SOIC package, quantity, and whether the procurement organization requires traceability or additional handling.
What is the lead time for INA134UA/2K5?
The current lead time for INA134UA/2K5 should be requested through the Request a Quote form on this page. Lead time can depend on order quantity, requested packaging, inventory position, and contractual purchasing terms, so a single figure would not remain accurate for every order. Confirm the complete INA134UA/2K5 MPN with the supplier before approving the purchase order to avoid ambiguity with other INA134 orderable variants.
Is INA134UA/2K5 in stock?
Current INA134UA/2K5 stock should be confirmed through the Request a Quote form on this page. The Texas Instruments ordering page identifies INA134UA/2K5 as a purchasable orderable device, but that does not by itself guarantee immediate inventory for every quantity. A stock response should include the requested quantity, reel quantity, packaging condition, and expected delivery schedule so procurement can determine whether the order can be released as planned.
INA134UA/2K5 vs INA2134UA/2K5 — which is better for audio input?
The INA134UA/2K5 and INA2134UA/2K5 are both unity-gain audio differential receivers from Texas Instruments and are associated with the same 8-pin SOIC class. The INA134UA/2K5 provides the established INA134 performance data of 0.0005% distortion at 1 kHz and a 14 V/us slew rate. Select INA2134UA/2K5 when its current datasheet ratings, lifecycle status, and ordering configuration better satisfy the project; confirm pin-level compatibility directly from each manufacturer datasheet before substitution.
When should I choose INA134UA/2K5 over INA2134UA/2K5?
Choose INA134UA/2K5 when an existing design specifies the INA134 family and benefits from its published 0 dB gain, 0.0005% distortion at 1 kHz, and 14 V/us slew-rate performance. Choose INA2134UA/2K5 when a new design is better supported by the newer related receiver’s lifecycle, supply, or device documentation. The decisive checks are exact pin compatibility, supply range, common-mode limits, output swing, temperature grade, and the manufacturer’s recommended decoupling layout.
What can replace INA134UA/2K5?
The closest documented replacement is the Texas Instruments INA2134UA/2K5 because it is a related unity-gain audio differential receiver in the same 8-pin SOIC format. The INA134UA itself is the same electrical device in a different orderable suffix and should not be treated as a distinct functional upgrade. Before using any replacement, compare every pin, the ±4 V to ±18 V supply range, input common-mode limits, output swing, distortion, slew rate, and thermal conditions against the manufacturer datasheets.
Is INA134UA/2K5 suitable for balanced professional audio input?
The INA134UA/2K5 is suitable for balanced professional audio input because it is designed as a unity-gain differential line receiver with 0.0005% distortion at 1 kHz and a 14 V/us slew rate. Its differential input can reject common-mode noise and cable-induced interference before conversion to a single-ended output. Actual headroom and fidelity still depend on the ±4 V to ±18 V supply choice, source impedance, input common-mode range, grounding, and correct use of the manufacturer’s reference and decoupling guidance.
How much power does INA134UA/2K5 dissipate?
The INA134UA/2K5 power dissipation depends on its quiescent current and the selected positive and negative supply voltages; its quiescent current is not stated in the product information shown here. Use the manufacturer datasheet’s supply-current and absolute-maximum tables to calculate worst-case dissipation. The SOIC copper area, ambient temperature, and adjacent heat sources must then be checked against the package thermal information before the device is approved for the enclosure and operating conditions.
Does INA134UA/2K5 meet RoHS and automotive requirements?
The INA134UA/2K5 is an industrial-temperature audio receiver in an 8-pin SOIC package, but its RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the product information shown here. Its -40°C to +85°C temperature range does not by itself establish AEC-Q100 qualification. Obtain the current manufacturer declarations for the exact orderable MPN before making a compliance claim, and use an explicitly automotive-qualified device for automotive production requirements.

Справочные инженерные данные для INA134UA/2K5 — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose INA134UA/2K5 when the circuit already uses the INA134 topology or requires a documented unity-gain differential receiver with 0.0005% distortion at 1 kHz and a 14 V/us slew rate. Its differential input is appropriate for balanced audio, mixer interfaces, active-speaker inputs, and industrial monitoring systems. Choose INA2134UA/2K5 for a related TI receiver in the same 8-pin SOIC format when its current datasheet, lifecycle position, and procurement conditions provide a better system-level fit. Treat INA2134UA as another ordering configuration rather than a fundamentally different circuit function. Before substitution, verify pin names, supply range, input common-mode limits, output swing, recommended decoupling, and the exact manufacturer orderable suffix. Neither option removes the need to check source impedance, grounding, cable protection, and thermal conditions.

Сравнение с аналогами

Параметр Этот товар INA2134UA/2K5 INA2134UA
Brand Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC (D) 8-pin SOIC 8-pin SOIC
Device Type Single audio differential line receiver Audio differential line receiver Audio differential line receiver
Differential Gain 0 dB (G = 1) 0 dB (G = 1) 0 dB (G = 1)
Operating Temperature -40°C to +85°C -40°C to +85°C -40°C to +85°C
Internal Precision Resistors Yes Yes Yes
Orderable Suffix /2K5 /2K5 Base orderable suffix

Ключевые отличия

  • Published low-distortion performance (против INA2134UA/2K5)
  • Unity-gain differential receiver (против INA2134UA)
  • Industrial temperature coverage (против INA2134UA/2K5)
  • Established INA134 application positioning (против INA2134UA)

Заметки по проектированию

Select positive and negative supply rails within the specified ±4 V to ±18 V range, while separately checking output swing and input common-mode limits at the actual signal level. Place the manufacturer-recommended bypass capacitors close to the supply pins and keep return-current paths short. Because the device has a unity gain, headroom is consumed mainly by internal architecture and output swing rather than feedback gain; unused output swing should be retained for transients rather than operating near the rail.

Route the two inputs as a closely coupled differential pair and keep them away from switching nodes and high-current return paths. The receiver’s differential architecture rejects common-mode noise, but imperfect pair geometry can reduce that benefit. Connect the ground and reference network as shown in the manufacturer application guidance, and place input-network components near the receiver pins. Avoid long loops between the source, input pins, and their return path because they can reintroduce pickup that the receiver is intended to reject.

Check the source impedance and bandwidth before finalizing the input network. A 14 V/us slew rate supports fast audio transients, but the complete signal path still depends on the amplifier’s gain-bandwidth response, output loading, and source impedance. Use the manufacturer typical-performance curves and recommended application circuit to select resistor and capacitor values, and test the assembled board for low-frequency channel differences and high-frequency differential-mode pickup.

Do not treat the 0 dB gain as permission to ignore input and output headroom. Verify that the balanced source remains within the input common-mode region and that the single-ended output remains within the specified swing for the selected supplies. A dual-supply receiver also requires correct negative-rail generation and startup sequencing. Check pin names directly in the manufacturer pin table before PCB release, especially when comparing INA134 and INA2134 orderable devices.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Qualified
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The device is identified as an industrial-temperature, 8-pin SOIC audio receiver. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available manufacturer and distributor information. No AEC-Q100 qualification is identified for this exact orderable device.

Данные проверены: 2026-11-19 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

INA134UA/2K5 datasheet INA134UA/2K5 pinout INA134UA/2K5 datasheet pdf INA134UA/2K5 specifications Texas Instruments INA134UA/2K5 INA134UA/2K5 equivalent INA134UA/2K5 replacement INA134UA/2K5 vs INA2134UA/2K5 INA134UA/2K5 price INA134UA/2K5 stock INA134 8-SOIC pinout INA134 balanced audio receiver

Связанные компоненты & термины

Texas Instruments INA134UA/2K5 INA134UA INA2134UA/2K5 INA2134UA OPA134UA audio differential line receiver differential receiver operational amplifier signal-conditioning IC analog amplifier semiconductor unity gain 0 dB common-mode rejection slew rate 14 V/us distortion dual supply balanced audio 8-pin SOIC SOIC package family surface mount professional audio Texas Instruments INA134
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ