LM224J/NOPB - 4-Op-Amp, 1MHz, 14-CDIP | Texas Instruments
MPN: LM224J/NOPB ✓ AktifLM224J/NOPB Ringkasan
An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify voltage differences. The LM224 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Four independent amplifiers are integrated into one package, allowing a circuit to perform gain, buffering, comparison, summation, filtering, and transducer-signal conditioning without using four separate packages.
The LM224 combines four general-purpose amplifiers with low-power operation, internally compensated closed-loop stability, and support for both single- and split-supply systems. Its 1 MHz gain-bandwidth product is suitable for audio-frequency and general instrumentation tasks, while its 0.5 V/µs slew rate limits large-signal performance in fast transient applications. The 14-CDIP package provides through-hole mounting for conventional industrial and laboratory boards.
Each of the four circuits has independent input, output, and power connections, while the common supply architecture permits operation from a single rail or from positive and negative rails. Internal frequency compensation removes the need for an external dominant-pole capacitor in the standard closed-loop configurations. Engineers can therefore use stable unity-gain voltage-follower, non-inverting, and inverting amplifier arrangements without redesigning compensation networks.
Typical uses include low-frequency sensor signal conditioning, process-control instrumentation, audio preamplification, active filtering, data acquisition, and general test equipment. The same quad-amplifier organization allows one package to implement several stages, reducing component count and simplifying interstage routing on a through-hole circuit board.
When designing around the LM224J/NOPB, verify input and output common-mode limits for the selected supply voltage, maintain the required output-current margin, and include suitable bypassing close to the supply pins. The 1 MHz bandwidth and 0.5 V/µs slew rate make it more appropriate for low-frequency precision conditioning than for wideband video, RF, or high-speed data acquisition.
This product record combines package, electrical, application, replacement, and engineering guidance in one place. It also identifies the distinction between electrically compatible quad amplifiers and true same-package drop-in choices, helping engineers evaluate PCB reuse, supply compatibility, temperature grade, and signal-bandwidth requirements before releasing a replacement into production.
Pilihan pengganti yang segera untuk LM224J/NOPB — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera LM224J/NOPB (sama faktor bentuk dan kaki) — berbeza dalam Compensation, Mounting Type, Package.
LM224N/NOPB
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
LM124J/NOPB
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LM324J/NOPB
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LM224J
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM224J
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM224J/NOPB Penilaian maksimum & Ciri-ciri Elektrik
| Amplifier Type | General Purpose |
| Number of Circuits | 4 circuits |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.5 V/µs |
| Supply Voltage Range | 3 V to 32 V |
| Supply Configuration | Single or split supply |
| Compensation | Internal frequency compensation |
| Open-Loop Gain | High gain |
| Power Consumption | Low power |
| Kemasan | 14-CDIP (0.300 in, 7.62 mm) |
| Packaging | Tube |
| Jenis Pemasangan | Through-hole |
Panduan Konfigurasi Pin LM224J/NOPB 14-cdip (0.300 in, 7.62 mm)
Konfigurasi pin untuk LM224J/NOPB (14-cdip (0.300 in, 7.62 mm) pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk LM224J/NOPB.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
LM224J/NOPB patut untuk 6 aplikasis: Industrial Sensor Signal Conditioning, Audio Preamplifier and Mixer, Process Control Instrumentation, Data Acquisition Front End, Active Filtering and Equalization, Power Supply Monitoring and Control.
Industrial Sensor Signal Conditioning
The LM224J/NOPB is well suited to conditioning low-frequency industrial sensor signals because it integrates four general-purpose amplifiers with a 1 MHz gain-bandwidth product and internal frequency compensation. Two stages can amplify and buffer a transducer output, while the remaining channels perform active filtering or level shifting. The 3 V to 32 V supply range supports conventional industrial rails, although each input must remain inside the amplifier’s common-mode limits. The 14-CDIP package is particularly useful for repair and expansion of legacy through-hole control boards.
Disebarkan
Audio Preamplifier and Mixer
The LM224J/NOPB can implement several low-frequency audio stages in one 14-CDIP package. Its four independently configured amplifiers support microphone preamplification, volume control, active equalization, and summing without requiring four separate ICs. The 1 MHz gain-bandwidth product covers conventional audio-band circuitry, while the 0.5 V/µs slew rate should be checked against the largest required signal swing and load. Internal frequency compensation makes standard non-inverting and inverting stages straightforward, provided feedback and grounding are laid out carefully.
Disebarkan
Process Control Instrumentation
The LM224J/NOPB fits process-control signal paths that operate over a wide supply range and require several precision amplifier functions. Its four circuits can support current-to-voltage conversion, error amplification, active filtering, and output buffering within one package. The 3 V to 32 V capability accommodates many 24 V industrial systems, while the 1 MHz bandwidth is more than adequate for most slow process variables. Designers should still verify common-mode range, output drive, thermal conditions, and isolation requirements before connecting the amplifier to field wiring.
Disebarkan
Data Acquisition Front End
The LM224J/NOPB can form the analog front end of a low-frequency data-acquisition system by providing differential or single-ended gain stages, anti-alias filtering, and output buffering. Four independent amplifiers allow several channels to share one package, reducing board area and simplifying routing on a through-hole design. The internal compensation supports stable closed-loop operation, and the 1 MHz gain-bandwidth product covers signals well below high-speed sampling requirements. The main design limits are input offset, bias current, common-mode range, and the need to keep the output within the selected supply’s linear range.
Disebarkan
Active Filtering and Equalization
The LM224J/NOPB is appropriate for first- and second-order active filters operating well below its 1 MHz gain-bandwidth limit. Four amplifiers can implement multiple filter sections, instrumentation stages, or programmable equalizer paths in a single package. Internal frequency compensation simplifies unity-gain and standard feedback configurations, while the 0.5 V/µs slew rate supports ordinary audio and control-frequency waveforms. Component tolerances and output loading should be checked when defining gain and cutoff accuracy, and power-supply bypassing should be placed close to the package.
Disebarkan
Power Supply Monitoring and Control
The LM224J/NOPB can monitor and control low-frequency power-system signals using up to four amplifiers for sensing, filtering, comparison, and error amplification. Its 3 V to 32 V supply range permits operation in 5 V, 12 V, and 24 V systems, but the amplifier inputs and outputs cannot automatically be assumed to tolerate the full supply voltage. The 1 MHz bandwidth is suitable for slow feedback loops rather than high-frequency compensation. Confirm source impedance, output current, fault behavior, and isolation requirements in the final power-control circuit.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk LM224J/NOPB — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | LM224N/NOPB | LM124J/NOPB | LM324J/NOPB | LM224J | LM224J |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | National Semiconductor | Motorola |
| Package | 14-CDIP (0.300 in, 7.62 mm) | 14-CDIP (0.300 in, 7.62 mm) | 14-CDIP (0.300 in, 7.62 mm) | 14-CDIP (0.300 in, 7.62 mm) | 14-CDIP (0.300 in, 7.62 mm) | 14-CDIP (0.300 in, 7.62 mm) |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
Penyeberangsung Jelas
- Four independent amplifiers in one through-hole package (vsLM324J/NOPB)
- Wide supply operating envelope (vsLM124J/NOPB)
- Compatible 1 MHz bandwidth architecture (vsLM224J)
- Original-manufacturer sourcing options (vsLM224J)
Catatan Desain
Bypass the common supply pins close to the 14-CDIP package and preserve a low-impedance ground return. The LM224 can operate from 3 V to 32 V, but the usable input and output range is narrower than the full supply span. Confirm common-mode limits at the minimum operating voltage and ensure the output remains inside its linear swing range under the expected load.
Use the manufacturer pin diagram as the authority for orientation and socket or PCB connectivity. Keep each amplifier’s input and feedback routes short, avoid routing between high-impedance input pins and switching-power traces, and place optional input-bias resistors close to their associated pins. Through-hole lead spacing and pin-1 orientation must be checked against the physical footprint before assembly.
Do not select the LM224 for applications requiring high precision without checking input-offset voltage, input-bias current, output-current capability, and common-mode limits. The 1 MHz gain-bandwidth product and 0.5 V/µs slew rate are adequate for general low-frequency work but can become limiting in precision DC systems or large-signal audio stages. Decouple supply rails and avoid floating unused amplifier inputs.
Although each channel is internally compensated, high source impedances can introduce extra phase error, and capacitive loading can reduce stability. Keep feedback-component leads short, place compensation or filter capacitors according to the selected topology, and use an output isolation resistor when driving capacitive loads. Validate stability with the actual source resistance, load, supply, and PCB geometry.
Maklumat Kesediaan
The /NOPB ordering suffix identifies a lead-free package configuration, but explicit RoHS, REACH, halogen-free, and conflict-minerals statements require confirmation from the manufacturer product documentation.