STMicroelectronics

LM2902WDT - Low-Power Quad Op Amp | STMicroelectronics

MPN: LM2902WDT ✓ Aktif
3 V to 32 V Vdss 14-SOIC Package
MOQ: 1 |

LM2902WDT Ringkasan

The STMicroelectronics LM2902WDT is a low-power quad operational amplifier with four independent amplifiers in a 14-pin SOIC package. The device operates from a single 3 V to 32 V supply or from split supplies up to ±15 V, and its push-pull output stage supports low-impedance loading. The LM2902 family provides approximately 1 MHz unity-gain bandwidth, making it suitable for general-purpose signal conditioning, transducer amplification, filtering, and low-frequency control applications.

An operational amplifier, or op amp, is a high-gain, differential-input amplifier used to amplify the difference between two input voltages. Within the broader integrated-circuit hierarchy, the LM2902 belongs to the operational-amplifier family and the amplifier-IC category. Its four amplifier sections share supply pins but operate independently, allowing one package to implement four separate gain stages, buffers, comparators, or active-filter sections.

Key characteristics include four amplifier circuits in one package, a low-power design, push-pull output capability, and a 1 MHz unity-gain bandwidth. The 14-pin SOIC outline supports compact surface-mount layouts and automated assembly. The WDT suffix identifies the tape-and-reel ordering configuration used in production, while the 2902W device marking is associated with this low-power quad operational amplifier.

The LM2902 architecture is intended for general-purpose precision rather than high-speed or micropower applications. Its unity-gain bandwidth of approximately 1 MHz supports audio-frequency and control-loop work where slew rate, input noise, and common-mode behavior are less demanding than in instrumentation or signal-chain designs. Each amplifier can be configured with external resistors for non-inverting, inverting, summing, or differential gain stages.

Typical uses include industrial sensor interfaces, buffered analog control systems, low-frequency active filters, audio preamplifier stages, and general instrumentation. In a 24 V industrial control board, the device can operate from a regulated 24 V rail or from lower split supplies while maintaining compatibility with conventional analog signal levels. Its quad organization can reduce component count when four similar analog functions are required.

When designing around the LM2902WDT, verify the output-current requirements, input common-mode range, and output-swing limits at the intended supply voltage and load. Avoid placing the device where saturation recovery time or AC noise specifications are more important than low cost and general-purpose functionality. Decoupling near the supply pins and short feedback traces help preserve stable operation in feedback configurations.

This page brings together package details, verified distributor references, pin assignments, and engineering-oriented guidance for designers evaluating the LM2902WDT in new analog boards or as a maintenance replacement for an existing quad op amp. It also distinguishes the available LM2902 package options so engineers can select the correct ordering code for assembly and production.

Pilihan pengganti yang segera untuk LM2902WDT — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera LM2902WDT (sama faktor bentuk dan kaki) — berbeza dalam Package, Product Type, Input Bias Current, Input Offset Current, Supply Voltage Range.

onsemi
Package: 14-TSSOP
Supply Voltage Range: 3 V to 26 V
Bandingkan Dengan LM2902WDT →
STMicroelectronics
Package: 14-SO
Input Bias Current: 2 nA
Input Offset Current: 20 nA
Bandingkan Dengan LM2902WDT →
STMicroelectronics
Package: 14-TSSOP
Product Type: Low-power quad operational amplifier
Input Bias Current: 20 nA
Bandingkan Dengan LM2902WDT →

LM2902WYDT

✅ Masuk Drop-In
STMicroelectronics
📦 SOIC-14
4 circuits · Standard general-purpose operational amplifier · 1.3 MHz · 100 dB · 375 uA · 20 nA · 2 nA · 800 V

Hubungi untuk harga

Lihat Datasheet →

LM2902WYPT

✅ Masuk Drop-In
STMicroelectronics
📦 SOIC-14
4 amplifiers · Low-power quad operational amplifier · 1.3 MHz · 100 dB · 375 uA · 20 nA · 2 nA · 800 V

Hubungi untuk harga

Lihat Datasheet →

LM2902DTB

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
onsemi
📦 SOIC-14
Quad operational amplifier · onsemi · 3 V to 26 V · 4 circuits · 14-TSSOP · Surface mount · 1.2 MHz · 2 mV

Hubungi untuk harga

Lihat Datasheet →

LM2902YDT

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 SOIC-14
Same LM2902 quad-amplifier family and 14-pin SOIC footprint; the Y suffix denotes a different ordering or temperature configuration

📋 Alternatif rujukan (tidak dalam katalog)

LM2902WDT

✅ Masuk Drop-In
STMicroelectronics
📦 SOIC-14
Quad Operational Amplifier · 4 circuits · General Purpose · 3 V to 32 V · 3 V to 32 V · 3 V to 32 V · ±15 V / 30 V total · 1 MHz

Hubungi untuk harga

Lihat Datasheet →

LM2902WDT Penilaian maksimum & Ciri-ciri Elektrik

Product Type Quad Operational Amplifier
Number of Amplifier Circuits 4 circuits
Amplifier Class General Purpose
Supply Voltage Range 3 V to 32 V
Total Supply Voltage Range 3 V to 32 V
Single-Supply Operation 3 V to 32 V
Dual-Supply Operation ±15 V / 30 V total
Unity-Gain Bandwidth 1 MHz
Jenis Output Push-Pull
Design Emphasis Low power
Bilangan Pin 14 pins
Kemasan 14-SOIC
Jenis Pemasangan Surface Mount
Order Configuration Tape and reel (WDT)
Device Marking 2902W

Konfigurasi Pin LM2902WDT

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
Pin 1 OUT1 — Amplifier 1 output
Pin 2 -IN1 — Amplifier 1 inverting input
Pin 3 +IN1 — Amplifier 1 non-inverting input
Pin 4 V- — Negative supply connection
Pin 5 +IN2 — Amplifier 2 non-inverting input
Pin 6 -IN2 — Amplifier 2 inverting input
Pin 7 OUT2 — Amplifier 2 output
Pin 8 OUT3 — Amplifier 3 output
Pin 9 -IN3 — Amplifier 3 inverting input
Pin 10 +IN3 — Amplifier 3 non-inverting input
Pin 11 V+ — Positive supply connection
Pin 12 +IN4 — Amplifier 4 non-inverting input
Pin 13 -IN4 — Amplifier 4 inverting input
Pin 14 OUT4 — Amplifier 4 output

Aplikasi Biasa

LM2902WDT patut untuk 6 aplikasis: Industrial Sensor Signal Conditioning, Low-Frequency Active Filters, Audio Preamplifier and Mixer, Analog Control and Feedback Loops, Power Supply Monitoring and Protection, General-Purpose Instrumentation Buffering.

🏭

Industrial Sensor Signal Conditioning

The LM2902WDT fits industrial sensor interfaces that require amplification of slowly varying analog signals. Its four independent amplifier sections can condition resistive, capacitive, or current-based sensors, while the 3 V to 32 V supply range allows operation from compact 5 V electronics or higher industrial rails. The approximately 1 MHz unity-gain bandwidth is sufficient for low-frequency process variables such as temperature, pressure, and position. Use one section as a non-inverting or differential gain stage, add filtering on the sensor input, and verify the common-mode range at the lowest operating supply. The four-section package reduces footprint compared with separate single amplifiers while retaining independent grounding and feedback routing.

🔧

Low-Frequency Active Filters

The LM2902WDT is appropriate for first- and second-order active filters operating well below its approximately 1 MHz unity-gain bandwidth. Four amplifiers can implement Sallen-Key sections, buffered anti-alias stages, or cascaded low-pass and high-pass networks. Its 3 V to 32 V operating range supports both portable 3.3 V or 5 V systems and higher-voltage analog control boards. Component tolerances and the amplifier's input-voltage and output-swing limits determine the practical filter accuracy, so check those curves in the manufacturer datasheet. Decouple the supply pins and keep the summing node and feedback components compact to reduce parasitic oscillation and sensitivity.

🎧

Audio Preamplifier and Mixer

The LM2902WDT can implement low-frequency audio preamplifier, summing, and mixing stages when a push-pull output and roughly 1 MHz unity-gain bandwidth are adequate. Each section supports resistor-defined inverting or non-inverting gain, allowing four microphone or line-level channels to share one package. The low-power quad organization helps limit board area in consumer audio equipment operating from a 5 V or 9 V rail. Keep each channel's feedback network local to its amplifier, and verify output-current demand because push-pull outputs still have finite drive limits. This device is better suited to conventional audio paths than to low-noise microphone preamplifiers requiring very low input-voltage noise.

⚡

Analog Control and Feedback Loops

The LM2902WDT is suitable for slow proportional, integral, and derivative control loops where the signal bandwidth remains modest. Its four amplifier sections can implement an error amplifier, an integrator, a differentiator, and a buffer in one package. Operation from 3 V to 32 V provides flexibility for 24 V industrial control systems as well as lower-voltage instrumentation. Stability depends on the noise gain and feedback-network values, so follow the manufacturer guidance for capacitive loads and verify phase margin in the final circuit. A local bypass capacitor at the supply pins reduces high-frequency coupling between control channels, while separate input and output routing prevents feedback paths from coupling.

🔋

Power Supply Monitoring and Protection

The LM2902WDT can implement window comparators, overvoltage detectors, and threshold amplifiers for low-cost power monitoring systems. Each amplifier compares a divided feedback voltage with a reference node and produces a logic-compatible indication through its push-pull output. The 3 V to 32 V operating range allows monitoring circuitry to operate directly from the rail it supervises, provided the maximum supply rating is not exceeded. Account for the input common-mode range, output saturation behavior, and output-current demand when driving status LEDs or digital inputs. The four-channel arrangement enables monitoring of multiple rails where space is constrained.

📟

General-Purpose Instrumentation Buffering

The LM2902WDT provides four unity-gain or simple-gain buffers for impedance isolation in instrumentation and test fixtures. Buffers prevent sensor and divider networks from being loaded by subsequent analog stages, while separate amplifier sections can implement gain, summation, and active filtering around the buffered signal. The approximately 1 MHz bandwidth supports measurements at low and moderate frequencies rather than wideband data acquisition. Place the buffer input pins away from high-current switching nodes and provide local supply bypassing to reduce offset coupling. Verify input offset, bias current, and common-mode limits when the source impedance is high, since those parameters determine the achievable DC accuracy.

What is the LM2902WDT?
The LM2902WDT is a low-power, general-purpose quad operational amplifier from STMicroelectronics. It contains four independent amplifier sections in a 14-pin SOIC package with a push-pull output stage. According to the manufacturer datasheet listing, the device supports single-supply operation from 3 V to 32 V and dual-supply operation to ±15 V, with approximately 1 MHz unity-gain bandwidth. It is intended for general-purpose analog signal conditioning rather than high-speed precision amplification.
What are the key specifications of LM2902WDT that engineers should know?
The principal LM2902WDT specifications are four amplifier circuits, a 3 V to 32 V supply range, ±15 V dual-supply capability, push-pull outputs, and approximately 1 MHz unity-gain bandwidth. The STMicroelectronics part is packaged as a 14-SOIC and is ordered in tape-and-reel form under the WDT suffix. These parameters make the device suitable for low-frequency buffering, amplifier, summing, and filtering circuits where a compact quad package is preferable to four separate single amplifiers.
Where can I download the LM2902WDT datasheet PDF?
The LM2902WDT datasheet PDF can be obtained from the manufacturer datasheet listing or through the distributor datasheet links on this page. STMicroelectronics describes the device as a low-power quad operational amplifier, and the published document contains the electrical characteristics, pin configuration, and application information. Download the current manufacturer document before finalizing a design so that supply limits, common-mode range, output swing, and temperature grades are checked against the latest revision.
What is the LM2902WDT pinout?
The LM2902WDT uses a standard 14-pin SOIC arrangement with four amplifier sections. Pins 1, 2, and 3 correspond to amplifier 1 output, inverting input, and non-inverting input; pins 4 and 11 are the negative and positive supply connections. Pins 7 and 14 are amplifier 2 and amplifier 4 outputs, while pins 5, 6, 9, 10, 12, and 13 serve the remaining amplifier inputs. Verify the pin-description table in the manufacturer datasheet before assigning PCB tracks.
Can LM2902WDT run from a single 5 V supply?
Yes, the LM2902WDT can run from a single 5 V supply because its stated operating range extends down to 3 V. The device also supports single-supply operation across 3 V to 32 V. With a 5 V rail, the usable signal range and output swing are more restricted than with a larger supply, so the input common-mode range and output-swing curves should be checked in the manufacturer datasheet for the specific load current.
What is the LM2902WDT equivalent to for drop-in replacement?
The closest same-package replacements include STMicroelectronics LM2902WYDT and LM2902WYPT, plus the ROHM Semiconductor LM2902WDT, all of which use a 14-pin SOIC format. Compatibility is strongest when the replacement has the same amplifier count, supply range, output architecture, and temperature grade. A working-board substitution should also be checked for offset-voltage, bias-current, noise, common-mode, and lifecycle differences rather than package appearance alone.
What is the difference between LM2902WDT and LM2902WYDT?
The LM2902WDT and LM2902WYDT are both STMicroelectronics quad operational amplifiers listed in 14-SOIC packages. Their primary ordering difference is the suffix, which can encode grade and packaging details; the exact electrical distinction must be confirmed from the corresponding manufacturer datasheets. Because both use the same 14-pin SOIC outline, they can serve as drop-in candidates, but production qualification should verify temperature range, supply limits, and automotive qualification needs.
Is LM2902WDT the same as LM324?
The LM2902WDT and the LM324 are related general-purpose quad operational amplifier families, but they are not automatically interchangeable. The LM2902WDT has a stated operating range of 3 V to 32 V and is commonly associated with an industrial temperature grade, while LM324 variants differ by manufacturer and grade. Pin assignments, input common-mode behavior, offset voltage, noise, output-current capability, and temperature specifications must all be compared before substitution.
When should I choose the LM2902WDT instead of LM2902WYDT?
Choose the LM2902WDT when your BOM, PCB layout, and manufacturing process specifically call for the WDT ordering code and its associated grade and reel configuration. Choose LM2902WYDT when that suffix is the part already validated on the board or when it provides the required temperature or qualification profile. Since both are 14-pin SOIC devices, compare the manufacturer datasheets for electrical ratings, temperature range, and qualification status before deciding.
What is the best ROHM equivalent for the STMicroelectronics LM2902WDT?
The ROHM Semiconductor LM2902WDT is the most direct cross-brand candidate identified for the STMicroelectronics LM2902WDT because it uses the same manufacturer part number and a 14-pin SOIC package. According to the ROHM distributor listing, it is a standard general-purpose four-circuit amplifier. Treat the device as a candidate drop-in and compare its electrical characteristics, temperature grade, supply range, and qualification documentation with the STMicroelectronics version before production use.
What can replace an LM2902WDT on an existing PCB?
A practical replacement for the LM2902WDT must use the same 14-pin SOIC footprint and provide four amplifier sections with compatible supply and input arrangements. LM2902WYDT, LM2902WYPT, and the ROHM Semiconductor LM2902WDT are the closest listed candidates. Confirm the original board's decoupling, load currents, common-mode input levels, and required temperature grade. Never substitute solely because the package has 14 pins; amplifier pin functions must also match.
Is LM2902WDT suitable for audio and control applications?
The LM2902WDT is suitable for many audio-frequency and low-frequency control applications because it provides approximately 1 MHz unity-gain bandwidth and push-pull outputs. It can buffer microphone-level signals, form active filters, and amplify slow sensor signals when higher slew rate, lower distortion, and tighter noise specifications are not required. Use the datasheet limits to confirm output swing and stability with the selected feedback network and load.
How should I decouple a LM2902WDT circuit?
Place the supply bypass capacitor as close as practical to the positive and negative supply pins, and follow the manufacturer layout and application guidance. Keep input, output, and feedback routes short, especially around the amplifier driving higher-capacitance loads. Because a 14-pin quad package contains four amplifiers, a single bypass capacitor may serve the entire IC, but additional local decoupling can be useful when several amplifier outputs switch or drive separate loads.
Where can I buy LM2902WDT online?
The LM2902WDT can be ordered through the distributor listings linked on this page, or you can submit a request through the Request a Quote form on this page for current availability, lead time, and commercial terms. The part is identified as a 14-SOIC, four-circuit, push-pull, low-power operational amplifier. When requesting a quote, include the required quantity, reel or tray packaging preference, target delivery date, and any automotive qualification requirements.
What is the price and lead time of LM2902WDT?
Current commercial pricing and lead time for the LM2902WDT are obtained through the Request a Quote form on this page. The linked distributor listings identify the component as a 14-SOIC low-power quad operational amplifier, but live stock and delivery commitments can change with demand and region. Submit the required quantity and target shipment date with the quote request to obtain a current quotation and the supplier's latest schedule.
Is LM2902WDT in stock?
The LM2902WDT is listed as an in-stock component by the distributor references shown on this page, but inventory changes rapidly and should not be treated as a guaranteed allocation. Use the Request a Quote form to request a current stock confirmation for your required quantity. For production planning, request the complete reel quantity, accepted delivery date, and any traceability or lot-control requirements at the same time.

Data referensi kejuruteraan untuk LM2902WDT — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Select the STMicroelectronics LM2902WDT when the design requires four general-purpose amplifiers in a 14-pin SOIC and operates across a 3 V to 32 V supply range. It is well suited to industrial sensor conditioning, low-frequency active filters, audio summing stages, slow control loops, and multi-rail threshold monitoring. Choose LM2902WYDT or LM2902WYPT when those specific suffixes are required by qualification records, temperature-grade requirements, or an existing approved BOM. LM2902DT and LM2902YDT are additional same-family ordering candidates, but their grade and temperature details must be checked before use. The ROHM Semiconductor LM2902WDT is a practical cross-brand candidate with the same MPN and package, yet it should be qualified as a distinct manufacturer device rather than treated as automatically identical. None of these choices is appropriate when the circuit requires rail-to-rail inputs, very low noise, high output current, or bandwidth well above approximately 1 MHz.

Perbandingan dengan Gantian

Parametr Produk Ini LM2902WYDT LM2902WYPT LM2902DT LM2902YDT LM2902WDT
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics ROHM Semiconductor
Package 14-SOIC 14-SOIC 14-SOIC 14-SOIC 14-SOIC 14-SOIC
Amplifier Count 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits
Ordering Configuration WDT tape-and-reel configuration WYDT ordering configuration WYPT ordering configuration DT ordering configuration YDT ordering configuration ROHM Semiconductor WDT ordering configuration

Penyeberangsung Jelas

  • Four independent amplifiers share one compact package (vsLM2902WYDT)
  • Wide single-supply operating range (vsLM2902WYPT)
  • Direct cross-brand sourcing path (vsLM2902WDT from ROHM Semiconductor)

Catatan Desain

Place the supply bypass capacitor adjacent to the positive and negative supply pins, and route each amplifier's feedback components close to its output and input pins. The four internal amplifiers share the package supply leads, so good local decoupling limits interaction between channels. Avoid routing input and feedback traces beneath or beside push-pull output nodes, especially where one output can switch while another channel is measuring a small signal.

Do not assume that every 14-pin quad amplifier is a drop-in replacement. Confirm the amplifier pin functions, positive and negative supply pins, input common-mode range, and output-swing limits before fitting an LM2902 variant. In particular, the ROHM LM2902WDT and the STMicroelectronics suffix variants require datasheet-level comparison of offset voltage, bias current, noise, supply limits, and temperature grade before production substitution.

Keep closed-loop bandwidth below the amplifier's approximately 1 MHz unity-gain bandwidth and avoid driving long capacitive loads unless the load and stability conditions are covered by the manufacturer guidance. Check output current for capacitive input filters and for cable or probe connections. When higher slew rate, lower distortion, or lower input noise is necessary, choose a different amplifier family rather than overdriving the LM2902.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

Compliance declarations for the STMicroelectronics LM2902WDT were not present in the cited component listings. Confirm RoHS, REACH, halogen-free, and conflict-minerals status from the manufacturer's current product documentation before release.

Data disahkan pada: 2026-11-17 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

LM2902WDT datasheet LM2902WDT datasheet pdf LM2902WDT pinout LM2902WDT equivalent LM2902WDT replacement LM2902WDT cross reference LM2902WDT vs LM2902WYDT LM2902WDT SOIC-14 pinout LM2902WDT supply voltage LM2902WDT 1 MHz bandwidth LM2902WDT sensor amplifier STMicroelectronics LM2902WDT LM2902WDT buy online LM2902WDT price and stock

Komponen dan Tanda berkaitan

STMicroelectronics LM2902WDT LM2902WYDT LM2902WYPT LM2902DT LM2902YDT ROHM Semiconductor LM2902WDT quad operational amplifier operational amplifier amplifier IC low-power amplifier push-pull output stage unity-gain bandwidth SOIC-14 surface mount single-supply operation dual-supply operation sensor signal conditioning active filter audio preamplifier industrial control power-supply monitoring
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ