LM2902WDT - Low-Power Quad Op Amp | STMicroelectronics
Teilenummer: LM2902WDT ✓ AktivLM2902WDT Übersicht
An operational amplifier, or op amp, is a high-gain, differential-input amplifier used to amplify the difference between two input voltages. Within the broader integrated-circuit hierarchy, the LM2902 belongs to the operational-amplifier family and the amplifier-IC category. Its four amplifier sections share supply pins but operate independently, allowing one package to implement four separate gain stages, buffers, comparators, or active-filter sections.
Key characteristics include four amplifier circuits in one package, a low-power design, push-pull output capability, and a 1 MHz unity-gain bandwidth. The 14-pin SOIC outline supports compact surface-mount layouts and automated assembly. The WDT suffix identifies the tape-and-reel ordering configuration used in production, while the 2902W device marking is associated with this low-power quad operational amplifier.
The LM2902 architecture is intended for general-purpose precision rather than high-speed or micropower applications. Its unity-gain bandwidth of approximately 1 MHz supports audio-frequency and control-loop work where slew rate, input noise, and common-mode behavior are less demanding than in instrumentation or signal-chain designs. Each amplifier can be configured with external resistors for non-inverting, inverting, summing, or differential gain stages.
Typical uses include industrial sensor interfaces, buffered analog control systems, low-frequency active filters, audio preamplifier stages, and general instrumentation. In a 24 V industrial control board, the device can operate from a regulated 24 V rail or from lower split supplies while maintaining compatibility with conventional analog signal levels. Its quad organization can reduce component count when four similar analog functions are required.
When designing around the LM2902WDT, verify the output-current requirements, input common-mode range, and output-swing limits at the intended supply voltage and load. Avoid placing the device where saturation recovery time or AC noise specifications are more important than low cost and general-purpose functionality. Decoupling near the supply pins and short feedback traces help preserve stable operation in feedback configurations.
This page brings together package details, verified distributor references, pin assignments, and engineering-oriented guidance for designers evaluating the LM2902WDT in new analog boards or as a maintenance replacement for an existing quad op amp. It also distinguishes the available LM2902 package options so engineers can select the correct ordering code for assembly and production.
Drop-in-Alternativen für LM2902WDT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LM2902WDT (gleiche Bauform und Footprint) – abweichend in Package, Product Type, Input Bias Current, Input Offset Current, Supply Voltage Range.
LM2902WYDT
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM2902WYPT
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM2902DTB
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →LM2902YDT
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
LM2902WDT
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM2902WDT Grenzwerte & elektrische Eigenschaften
| Product Type | Quad Operational Amplifier |
| Number of Amplifier Circuits | 4 circuits |
| Amplifier Class | General Purpose |
| Supply Voltage Range | 3 V to 32 V |
| Total Supply Voltage Range | 3 V to 32 V |
| Single-Supply Operation | 3 V to 32 V |
| Dual-Supply Operation | ±15 V / 30 V total |
| Unity-Gain Bandwidth | 1 MHz |
| Ausgangstyp | Push-Pull |
| Design Emphasis | Low power |
| Anzahl der Pins | 14 pins |
| Gehäuse | 14-SOIC |
| Montageart | Surface Mount |
| Order Configuration | Tape and reel (WDT) |
| Device Marking | 2902W |
LM2902WDT Pin-Konfiguration
| Pin 1 | OUT1 — Amplifier 1 output |
| Pin 2 | -IN1 — Amplifier 1 inverting input |
| Pin 3 | +IN1 — Amplifier 1 non-inverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | +IN2 — Amplifier 2 non-inverting input |
| Pin 6 | -IN2 — Amplifier 2 inverting input |
| Pin 7 | OUT2 — Amplifier 2 output |
| Pin 8 | OUT3 — Amplifier 3 output |
| Pin 9 | -IN3 — Amplifier 3 inverting input |
| Pin 10 | +IN3 — Amplifier 3 non-inverting input |
| Pin 11 | V+ — Positive supply connection |
| Pin 12 | +IN4 — Amplifier 4 non-inverting input |
| Pin 13 | -IN4 — Amplifier 4 inverting input |
| Pin 14 | OUT4 — Amplifier 4 output |
Typische Anwendungen
LM2902WDT ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Low-Frequency Active Filters, Audio Preamplifier and Mixer, Analog Control and Feedback Loops, Power Supply Monitoring and Protection, General-Purpose Instrumentation Buffering.
Industrial Sensor Signal Conditioning
The LM2902WDT fits industrial sensor interfaces that require amplification of slowly varying analog signals. Its four independent amplifier sections can condition resistive, capacitive, or current-based sensors, while the 3 V to 32 V supply range allows operation from compact 5 V electronics or higher industrial rails. The approximately 1 MHz unity-gain bandwidth is sufficient for low-frequency process variables such as temperature, pressure, and position. Use one section as a non-inverting or differential gain stage, add filtering on the sensor input, and verify the common-mode range at the lowest operating supply. The four-section package reduces footprint compared with separate single amplifiers while retaining independent grounding and feedback routing.
Empfohlen
Low-Frequency Active Filters
The LM2902WDT is appropriate for first- and second-order active filters operating well below its approximately 1 MHz unity-gain bandwidth. Four amplifiers can implement Sallen-Key sections, buffered anti-alias stages, or cascaded low-pass and high-pass networks. Its 3 V to 32 V operating range supports both portable 3.3 V or 5 V systems and higher-voltage analog control boards. Component tolerances and the amplifier's input-voltage and output-swing limits determine the practical filter accuracy, so check those curves in the manufacturer datasheet. Decouple the supply pins and keep the summing node and feedback components compact to reduce parasitic oscillation and sensitivity.
Empfohlen
Audio Preamplifier and Mixer
The LM2902WDT can implement low-frequency audio preamplifier, summing, and mixing stages when a push-pull output and roughly 1 MHz unity-gain bandwidth are adequate. Each section supports resistor-defined inverting or non-inverting gain, allowing four microphone or line-level channels to share one package. The low-power quad organization helps limit board area in consumer audio equipment operating from a 5 V or 9 V rail. Keep each channel's feedback network local to its amplifier, and verify output-current demand because push-pull outputs still have finite drive limits. This device is better suited to conventional audio paths than to low-noise microphone preamplifiers requiring very low input-voltage noise.
Empfohlen
Analog Control and Feedback Loops
The LM2902WDT is suitable for slow proportional, integral, and derivative control loops where the signal bandwidth remains modest. Its four amplifier sections can implement an error amplifier, an integrator, a differentiator, and a buffer in one package. Operation from 3 V to 32 V provides flexibility for 24 V industrial control systems as well as lower-voltage instrumentation. Stability depends on the noise gain and feedback-network values, so follow the manufacturer guidance for capacitive loads and verify phase margin in the final circuit. A local bypass capacitor at the supply pins reduces high-frequency coupling between control channels, while separate input and output routing prevents feedback paths from coupling.
Empfohlen
Power Supply Monitoring and Protection
The LM2902WDT can implement window comparators, overvoltage detectors, and threshold amplifiers for low-cost power monitoring systems. Each amplifier compares a divided feedback voltage with a reference node and produces a logic-compatible indication through its push-pull output. The 3 V to 32 V operating range allows monitoring circuitry to operate directly from the rail it supervises, provided the maximum supply rating is not exceeded. Account for the input common-mode range, output saturation behavior, and output-current demand when driving status LEDs or digital inputs. The four-channel arrangement enables monitoring of multiple rails where space is constrained.
Empfohlen
General-Purpose Instrumentation Buffering
The LM2902WDT provides four unity-gain or simple-gain buffers for impedance isolation in instrumentation and test fixtures. Buffers prevent sensor and divider networks from being loaded by subsequent analog stages, while separate amplifier sections can implement gain, summation, and active filtering around the buffered signal. The approximately 1 MHz bandwidth supports measurements at low and moderate frequencies rather than wideband data acquisition. Place the buffer input pins away from high-current switching nodes and provide local supply bypassing to reduce offset coupling. Verify input offset, bias current, and common-mode limits when the source impedance is high, since those parameters determine the achievable DC accuracy.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LM2902WDT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LM2902WYDT | LM2902WYPT | LM2902DT | LM2902YDT | LM2902WDT |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | ROHM Semiconductor |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Amplifier Count | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Ordering Configuration | WDT tape-and-reel configuration | WYDT ordering configuration | WYPT ordering configuration | DT ordering configuration | YDT ordering configuration | ROHM Semiconductor WDT ordering configuration |
Wichtigste Unterscheidungsmerkmale
- Four independent amplifiers share one compact package (vs. LM2902WYDT)
- Wide single-supply operating range (vs. LM2902WYPT)
- Direct cross-brand sourcing path (vs. LM2902WDT from ROHM Semiconductor)
Designhinweise
Place the supply bypass capacitor adjacent to the positive and negative supply pins, and route each amplifier's feedback components close to its output and input pins. The four internal amplifiers share the package supply leads, so good local decoupling limits interaction between channels. Avoid routing input and feedback traces beneath or beside push-pull output nodes, especially where one output can switch while another channel is measuring a small signal.
Do not assume that every 14-pin quad amplifier is a drop-in replacement. Confirm the amplifier pin functions, positive and negative supply pins, input common-mode range, and output-swing limits before fitting an LM2902 variant. In particular, the ROHM LM2902WDT and the STMicroelectronics suffix variants require datasheet-level comparison of offset voltage, bias current, noise, supply limits, and temperature grade before production substitution.
Keep closed-loop bandwidth below the amplifier's approximately 1 MHz unity-gain bandwidth and avoid driving long capacitive loads unless the load and stability conditions are covered by the manufacturer guidance. Check output current for capacitive input filters and for cable or probe connections. When higher slew rate, lower distortion, or lower input noise is necessary, choose a different amplifier family rather than overdriving the LM2902.
Compliance-Informationen
Compliance declarations for the STMicroelectronics LM2902WDT were not present in the cited component listings. Confirm RoHS, REACH, halogen-free, and conflict-minerals status from the manufacturer's current product documentation before release.