LM339PW - 4-Channel 36V Open-Collector Comparator | Texas Instruments
MPN: LM339PW ✓ AktifLM339PW Ringkasan
A differential comparator is an analog-to-digital decision component that compares two voltage inputs and changes its output when one input crosses the other. A quad comparator such as the LM339PW integrates four independent channels, making it part of the comparator IC hierarchy and the broader interface IC and semiconductor categories. Its open-collector outputs require an external pull-up resistor, allowing the output voltage, rise time, and interface standard to be selected by the system designer.
The verified LM339 family information highlights a maximum rating of up to 38 V, an HBM ESD rating of 2 kV, a low input offset of 0.37 mV, a low input bias current of 3.5 nA, and a typical supply current of 200 µA per comparator. A response time of 1 µs is also listed for the family. These characteristics make the device useful for level detection, threshold comparison, open-collector bus signaling, and industrial control functions where input signals can approach ground.
Each of the four channels is independent, so the device can perform unrelated comparisons without coupling the logic states of different channels. The open-collector architecture can sink output current while the external pull-up establishes the high state, which is useful for wired logic, relay-driver interfaces, and legacy TTL, MOS, or CMOS-compatible systems. Because output rise time depends on the pull-up resistance and total node capacitance, timing analysis must include the external network rather than relying only on the comparator response time.
Typical applications include industrial sensor-threshold monitoring, battery and power-supply protection, overvoltage detection, window comparators, and four-channel level translation. The ground-referenced common-mode capability is particularly useful for detecting the presence or absence of a signal from a 12 V or 24 V industrial sensor. A pull-up can also connect the open-collector outputs to an appropriate supply, allowing multiple comparators to form a wired signal function where the application and device specifications permit it.
When designing the PCB, place the pull-up resistor close to the open-collector output and route the node away from high-current switching paths. Decoupling capacitors should connect the supply and ground pins with a short return path. Because the package has no exposed thermal pad and the device can operate across a wide voltage range, engineers should verify the maximum differential input voltage, output current, and dissipation conditions against the manufacturer datasheet.
This page consolidates verified distributor and manufacturer information with package guidance, application analysis, commercial questions, and drop-in replacement details. It is intended to support faster component selection while clearly identifying specification fields, pricing, and pin-level details that still require confirmation from the appropriate manufacturer documentation.
Pilihan pengganti yang segera untuk LM339PW — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera LM339PW (sama faktor bentuk dan kaki) — berbeza dalam Comparator Type, Number of Channels, Output Type, Package, Propagation Delay.
LM239PWR
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LM2901PWR
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LM2901PT
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LM339PWR
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LM339PT
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM339PW Penilaian maksimum & Ciri-ciri Elektrik
| Comparator Type | Quad differential comparator |
| Number of Channels | 4 channels |
| Jenis Output | Open-collector |
| Supply Voltage Range | 2 V to 36 V |
| Maximum Family Rating | Up to 38 V |
| Propagation Delay | 300 ns |
| Family Response Time | 1 µs |
| Low Input Offset | 0.37 mV |
| Low Input Bias Current | 3.5 nA |
| Supply Current per Comparator | 200 µA typical |
| Common-Mode Input Range | Includes ground |
| Differential Input Voltage | Equal to maximum-rated supply voltage, up to ±38 V |
| ESD Rating HBM | 2 kV |
| Output Compatibility | Compatible with TTL, MOS, and CMOS |
| Kemasan | 14-pin TSSOP |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin LM339PW 14-pin tssop
Konfigurasi pin untuk LM339PW (14-pin tssop pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk LM339PW.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
LM339PW patut untuk 6 aplikasis: Industrial Sensor Threshold Detection, Power-Supply Overvoltage Protection, Battery Low-Level Detection, Window and Range Comparator, Open-Collector Interface and Level Translation, Motor and Actuator Limit Detection.
Industrial Sensor Threshold Detection
The LM339PW fits industrial sensor-threshold detection because its four independent channels operate from a verified 2 V to 36 V supply, and the common-mode input range includes ground. Each comparator can evaluate a sensor signal against a reference and use its open-collector output to signal a controller. A pull-up resistor establishes the digital high level, while the specified 300 ns propagation delay supports prompt threshold decisions. For a 12 V or 24 V sensor interface, designers should confirm the exact input, supply, and transient limits in the manufacturer datasheet.
Disebarkan
Power-Supply Overvoltage Protection
The LM339PW can supervise a power rail by comparing a divided feedback voltage with a reference and asserting an open-collector fault signal when the monitored voltage exceeds a threshold. Its 2 V to 36 V operating range accommodates many 5 V, 12 V, and 24 V systems, and its ground-inclusive common-mode range simplifies low-side threshold sensing. The 300 ns specified response helps limit fault propagation, although the final protection delay also includes the external divider, filters, pull-up network, and downstream logic delay.
Disebarkan
Battery Low-Level Detection
The LM339PW is appropriate for battery-level detection because a comparator channel can compare a divided battery voltage with a reference while remaining powered from a 2 V to 36 V source. The ground-inclusive common-mode range allows low battery voltages to be sensed without a negative supply. The open-collector output can drive a pull-up and an MCU input or indicator, while the low 200 µA-per-comparator typical supply current helps limit standby overhead. Battery chemistry, tolerance stack-up, and the minimum operating voltage should be verified before release.
Disebarkan
Window and Range Comparator
Two LM339PW channels can implement a window comparator by comparing the monitored signal against upper and lower references. The fourth channel remains available for another independent decision, reducing the need for multiple comparator packages. With a 300 ns propagation delay and open-collector outputs, the device can report whether a voltage lies inside or outside a permitted range. The reference tolerance and resistor-network error determine the practical window accuracy, so production designs should include those errors rather than relying on the comparator offset alone.
Disebarkan
Open-Collector Interface and Level Translation
The LM339PW can translate a legacy or industrial logic signal through an externally pulled-up open-collector output. Because the pull-up sets the high-state voltage, the output can be referenced to a supply compatible with TTL, MOS, or CMOS receivers. The ground-inclusive input range supports sensing signals near zero volts, and the 300 ns propagation delay is suitable for ordinary digital control and alarm signals. System timing must include the RC rise time formed by the pull-up and wiring capacitance, especially on longer or slower nodes.
Disebarkan
Motor and Actuator Limit Detection
The LM339PW can monitor a motor, actuator, or solenoid control signal and identify an out-of-range condition before it reaches a hazardous state. Four independent channels allow several limit inputs to be evaluated by one package, and the open-collector fault output can be pulled up to the logic supply used by a controller. Its 2 V to 36 V supply range supports common industrial rails, but motor environments require separate analysis of inductive kickback, surge, ground bounce, and isolation. The comparator should not replace the protection components required by the motor driver.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk LM339PW — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | LM239PWR | LM2901PWR | LM2901PT | LM339PWR | LM339PT |
|---|---|---|---|---|---|---|
| Package | 14-TSSOP | 14-TSSOP - same footprint | 14-TSSOP - same footprint | 14-TSSOP - same footprint | 14-TSSOP - same footprint | 14-TSSOP - same footprint |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | ROHM Semiconductor | ROHM Semiconductor |
| Comparator Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Open-Collector Pull-Up Requirement | External pull-up required | External pull-up required | External pull-up required | External pull-up required | External pull-up required | External pull-up required |
Penyeberangsung Jelas
- Faster verified response than the ROHM LM339 alternatives (vsROHM Semiconductor LM339PWR)
- Lower verified family offset than the listed ROHM alternatives (vsROHM Semiconductor LM339PT)
- Single-source continuity with directly related TI grades (vsLM239PWR)
Catatan Desain
Do not treat the 2 V to 36 V operating range as an absolute-maximum rating. The verified manufacturer information states that family versions can reach a maximum rating of up to 38 V and permits differential input voltages up to the maximum-rated supply voltage. Confirm the exact LM339PW limits, especially during supply transients, before selecting resistor values or relying on an input beyond the normal operating range.
Place the pull-up resistor close to the relevant open-collector output and keep the output trace away from inductors, motor nodes, and switching converter power paths. The resistor and trace capacitance determine the output rise time, so calculate the RC behavior for the longest supported trace. A separate ground return and short supply-decoupling connection help prevent comparator output transitions from coupling noise into sensitive input nodes.
Account for input filtering and hysteresis when using the four channels as threshold detectors. Comparator input offset, reference tolerance, resistor tolerance, and noise determine the effective switching threshold. Adding positive feedback creates hysteresis and prevents repeated output toggling, while input RC networks should be sized so their transient response remains faster than the verified 300 ns propagation-delay requirement of the LM339PW.
Maklumat Kesediaan
The supplied verified data does not provide suffix-specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements. These fields remain unknown rather than being inferred.
