Analog Devices

LT1022ACH - High-Speed Precision JFET Op Amp | Analog Devices

MPN: LT1022ACH ✓ Aktif
80 µV Vdss 50 pA Id TO-5 metal can with 8 leads Package
MOQ: 1 |

LT1022ACH Ringkasan

Analog Devices LT1022ACH is a high-speed, precision JFET-input operational amplifier with a 26 V/µs slew rate, 8.5 MHz gain-bandwidth product, and typically 80 µV offset voltage, housed in a TO-5 metal-can package. It combines low input bias current with precision DC performance for instrumentation, low-level signal conditioning, and active filtering.

A JFET-input operational amplifier is a voltage-amplifier IC whose input stage uses junction field-effect transistors. Within the semiconductor hierarchy, it belongs to the operational-amplifier family, analog amplifier ICs, and the broader signal-conditioning category. The JFET input stage provides very low bias current, while the precision amplifier architecture provides low offset voltage, low voltage drift, and stable operation over temperature.

Key performance characteristics include a typical slew rate of 26 V/µs and a guaranteed minimum of 23 V/µs. The device has an 8.5 MHz gain-bandwidth product, typical offset voltage of 80 µV, and maximum offset voltage of 250 µV. Input bias current is typically 50 pA at 70°C and 500 pA at 125°C, supporting high-impedance source applications. Output current capability is specified at 20 mA without gain degradation.

The precision of the LT1022ACH is supported by a typical input offset drift of 1.5 µV/°C and a maximum specified drift of 5 µV/°C. At elevated temperature, maximum offset voltage reaches 750 µV at 125°C. These characteristics make the amplifier suitable for closed-loop systems requiring accurate DC behavior while retaining useful high-speed response. The 8.5 MHz gain-bandwidth product supports moderately high closed-loop bandwidth, particularly at low noise gains.

Typical applications include precision test and measurement circuits, low-level sensor amplifiers, photodiode signal conditioning, precision active filters, audio preamplification, and low-level ADC input stages. The low bias current is particularly useful when driving high source impedances, while the 23 V/µs guaranteed minimum slew rate helps preserve large-signal response.

Designers should account for input bias-current temperature behavior and verify the selected feedback network against the amplifier's gain-bandwidth and stability characteristics. Decoupling capacitors should be placed close to the supply pins, and unused inputs must be biased within the input common-mode range to avoid saturation.

This product page combines manufacturer specifications, application-oriented engineering guidance, comparison criteria, and practical design notes for engineers evaluating the LT1022ACH as a precision, high-speed JFET-input amplifier.

Pilihan pengganti yang segera untuk LT1022ACH — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera LT1022ACH (sama faktor bentuk dan kaki) — berbeza dalam Amplifier Type, Package.

Analog Devices
Amplifier Type: High-speed precision JFET-input operational amplifier
Package: 8-terminal round TO-5 metal package
Bandingkan Dengan LT1022ACH →

Tiada pilihan pengganti yang segera untuk produk ini.

Minta Alternatif

LT1022ACH Penilaian maksimum & Ciri-ciri Elektrik

Amplifier Type 1-circuit precision JFET-input operational amplifier
Typical Slew Rate 26 V/µs
Guaranteed Minimum Slew Rate 23 V/µs
Gain-Bandwidth Product 8.5 MHz
Typical Input Offset Voltage 80 µV
Maximum Input Offset Voltage 250 µV
Maximum Input Offset Voltage at 125°C 750 µV
Typical Input Offset Drift 1.5 µV/°C
Maximum Input Offset Drift 5 µV/°C
Typical Input Bias Current at 70°C 50 pA
Typical Input Bias Current at 125°C 500 pA
Maximum Input Bias Current at 70°C 180 pA
Maximum Input Bias Current at 125°C 4 nA
Output Load Current Capability 20 mA without gain degradation
Kemasan TO-5 metal can with 8 leads
Jenis Pemasangan Through-hole

Panduan Konfigurasi Pin LT1022ACH to-5 metal can with 8 leads

Konfigurasi pin untuk LT1022ACH (to-5 metal can with 8 leads pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai to-5 metal can with 8 leads untuk LT1022ACH

Tiada data garisan pin yang diperoleh untuk LT1022ACH.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

LT1022ACH patut untuk 6 aplikasis: Precision Instrumentation Amplifier, Photodiode Signal Conditioning, Precision Active Filtering, Audio Preamplifier, Low-Level ADC Input Driver, Precision Buffer and Level Conditioning.

🧰

Precision Instrumentation Amplifier

The LT1022ACH fits low-level instrumentation circuits where the sensor or source resistance makes input bias current important. Its typical bias current of 50 pA at 70°C and 500 pA at 125°C limits leakage-induced error across high-value feedback resistors. The typically 80 µV offset voltage and 1.5 µV/°C drift support accurate DC measurements, while the 8.5 MHz gain-bandwidth product and 23 V/µs guaranteed minimum slew rate preserve response for signals that are not strictly static.

📷

Photodiode Signal Conditioning

A transimpedance amplifier built around the LT1022ACH can benefit from its low JFET input bias current, which is typically 50 pA at 70°C. That characteristic helps preserve weak current signals from photodiodes without excessive error across a high-value feedback resistor. The 26 V/µs typical slew rate and 8.5 MHz gain-bandwidth product are useful for moderate-bandwidth optical measurements. Compensation capacitance, sensor capacitance, and amplifier noise gain must be evaluated together to maintain stability.

🎛️

Precision Active Filtering

The LT1022ACH can serve as an active element in precision filter and signal-conditioning networks that combine high source impedance with moderate frequency requirements. Its low typical input bias current of 50 pA at 70°C reduces interaction with high-impedance stages, while the 8.5 MHz gain-bandwidth product provides useful closed-loop bandwidth. Offset drift is typically 1.5 µV/°C, but overall filter accuracy will still depend on resistor and capacitor tolerances, noise gain, and temperature stability.

🎧

Audio Preamplifier

The LT1022ACH suits low-level audio preamplification stages requiring low bias current and a faster response than a basic general-purpose amplifier. According to the Analog Devices LT1022 datasheet, it combines an 8.5 MHz gain-bandwidth product with a typical slew rate of 26 V/µs. The low offset voltage and drift reduce DC movement at the signal path, while the JFET input stage is compatible with high-impedance transducers. Headroom and output-swing limits must be checked against the required signal level.

📊

Low-Level ADC Input Driver

The LT1022ACH can drive the input of a high-resolution ADC when the source presents a substantial impedance and the converter requires a low-noise, accurate drive signal. The amplifier's typically 50 pA input bias current at 70°C helps reduce errors associated with source leakage and sampling-network charging. Its 8.5 MHz gain-bandwidth product supports moderate-bandwidth conversion systems, although the final settling time must be compared with the ADC acquisition requirements and sampling capacitor.

⚡

Precision Buffer and Level Conditioning

The LT1022ACH is useful as a precision buffer when a high-impedance source cannot drive the next stage directly and conventional amplifier input bias current would disturb the signal. Its typical 80 µV offset voltage, 1.5 µV/°C drift, and low JFET input bias current preserve small DC signals. The 20 mA load-current capability without gain degradation supports moderate output loading. Confirm the common-mode range and output swing against the source and destination signal levels in the final circuit.

What are the key specifications of LT1022ACH that engineers should know?
The LT1022ACH is a precision JFET-input operational amplifier featuring an 8.5 MHz gain-bandwidth product, a typical slew rate of 26 V/µs, and typically 80 µV input offset voltage. According to the Analog Devices LT1022 datasheet, input bias current is typically 50 pA at 70°C, while typical input offset drift is 1.5 µV/°C. The device also supports 20 mA of load current without gain degradation and is available in a TO-5 metal-can package.
What is the operating principle of the LT1022ACH JFET-input op amp?
The LT1022ACH uses a JFET input stage to provide very low input bias current while preserving precision DC behavior. According to the Analog Devices LT1022 datasheet, the amplifier combines a typical 80 µV offset voltage with a typical 1.5 µV/°C offset drift. This architecture is useful when the signal source has high output resistance or when leakage from the source or input protection network would otherwise create measurement errors.
How fast is the LT1022ACH and what limits large-signal response?
The LT1022ACH has a typical slew rate of 26 V/µs and a guaranteed minimum slew rate of 23 V/µs. According to the Analog Devices LT1022 datasheet, its gain-bandwidth product is 8.5 MHz. Small-signal bandwidth depends on the selected closed-loop gain and feedback network, while slew rate determines how quickly the output can traverse larger voltage changes without exceeding the amplifier's large-signal capability.
What is the input bias current of the LT1022ACH at elevated temperature?
The LT1022ACH input bias current is typically 50 pA at 70°C and 500 pA at 125°C. According to the Analog Devices LT1022 datasheet, the corresponding maximum values are 180 pA at 70°C and 4 nA at 125°C. These figures are important for photodiode, electrochemical-sensor, and high-impedance instrumentation circuits, where input leakage can create an output error across the feedback resistor.
How accurate is the LT1022ACH for low-level DC measurements?
The LT1022ACH offers typically 80 µV input offset voltage, a 250 µV maximum offset specification, and typically 1.5 µV/°C offset drift. According to the Analog Devices LT1022 datasheet, maximum drift is 5 µV/°C and maximum offset at 125°C is 750 µV. These characteristics make the device suitable for precision instrumentation, but final measurement accuracy still depends on resistor tolerances, reference quality, and calibration.
Where can I download the LT1022ACH datasheet PDF?
The LT1022ACH datasheet PDF can be downloaded from the listed manufacturer-document mirror or obtained from the official Analog Devices LT1022 product page. According to the Analog Devices LT1022 documentation, the device is a high-speed, precision JFET-input operational amplifier with an 8.5 MHz gain-bandwidth product and a typical 26 V/µs slew rate. Use the manufacturer document for final pin, supply-voltage, common-mode, and absolute-maximum ratings.
Where can I find the LT1022ACH pinout and package connection information?
The LT1022ACH pinout and connection information are presented in the manufacturer LT1022 datasheet's package and pin-description sections. The device uses a TO-5 metal-can package with eight leads, while the functional block diagram identifies the power, input, and output connections. Use the pin-description table in the Analog Devices document when assigning PCB tracks, selecting bypass-capacitor locations, and verifying the orientation of the metal can.
Is the LT1022ACH suitable for photodiode and high-impedance sensor amplifiers?
The LT1022ACH is suitable for many high-impedance sensor amplifiers because its input bias current is typically 50 pA at 70°C and 500 pA at 125°C. According to the Analog Devices LT1022 datasheet, the device also provides typically 80 µV offset voltage and an 8.5 MHz gain-bandwidth product. The application must still account for source capacitance, leakage, noise gain, and the feedback resistor chosen for the required transimpedance.
LT1022ACH vs MC3403DR - which is better for precision instrumentation?
The LT1022ACH is the better choice when very low bias current and higher precision are more important than a modern dual-package footprint. According to the Analog Devices LT1022 datasheet, it combines 50 pA typical input bias current at 70°C with typically 80 µV offset voltage. The MC3403DR is a general-purpose quad amplifier and does not provide the same JFET-input bias-current profile, so it is not a pin-to-pin substitute for the single TO-5 device.
When should I choose LT1022ACH over a general-purpose precision op amp?
Choose the LT1022ACH when the source impedance is high enough that input bias current would materially affect the measurement. According to the Analog Devices LT1022 datasheet, typical input bias current is 50 pA at 70°C, while offset voltage is typically 80 µV and gain-bandwidth is 8.5 MHz. A general-purpose amplifier may be preferable when source leakage is negligible and lower cost or a modern surface-mount package is the priority.
Is LT1022ACH suitable for active filters and precision signal conditioning?
The LT1022ACH fits precision active-filter and signal-conditioning designs that combine low bias current with useful AC performance. According to the Analog Devices LT1022 datasheet, it provides an 8.5 MHz gain-bandwidth product, a guaranteed minimum slew rate of 23 V/µs, and typically 80 µV offset voltage. Component tolerances and the selected topology will dominate practical filter accuracy, so simulate the complete circuit with the amplifier's specified noise-gain behavior.
Where can I buy LT1022ACH online and check its current availability?
Use the Request a Quote form on this page to ask about LT1022ACH availability, current lead time, and order quantity. The component is identified as a JFET-input operational amplifier in a TO-5 package, and the manufacturer product page lists the LT1022 family as an active product offering. A written quote is the appropriate route for checking exact suffix availability, including AH grade and package-handling requirements.
What is the price of LT1022ACH?
The current LT1022ACH quotation is available through the Request a Quote form on this page. The part is a single JFET-input operational amplifier in a TO-5 metal-can package with an 8.5 MHz gain-bandwidth product and a guaranteed minimum slew rate of 23 V/µs. When requesting a quote, state the required quantity, production quantity, and acceptable delivery schedule so the supplier can confirm current commercial terms.
What is the lead time for LT1022ACH?
The current LT1022ACH lead time should be confirmed through the Request a Quote form on this page. Lead time depends on the exact AH suffix, quantity, and manufacturing schedule rather than on the generic LT1022 family designation. The manufacturer product page continues to identify the LT1022 family, but a firm delivery commitment should be requested for the specific order quantity before incorporating the amplifier into a production schedule.
Is LT1022ACH in stock?
LT1022ACH inventory status should be confirmed through the Request a Quote form on this page. The component is a precision JFET-input operational amplifier with typically 50 pA input bias current at 70°C and a TO-5 metal-can package. Exact stock can change with order quantity and suffix requirements, so request the current quantity, delivery location, and target date with the inquiry.
What can replace LT1022ACH in a pin-compatible design?
No verified pin-compatible replacement for the LT1022ACH is established by the available cross-reference information. The LT1022ACH is a single JFET-input operational amplifier in an eight-lead TO-5 metal-can package, and a functional amplifier with the same electrical role may use different pins or require a different footprint. Use the Request a Quote form to discuss sourcing the original device, and require manufacturer pin and specification review before approving any substitution.
Is the LT1022ACH the same as a general-purpose precision amplifier?
The LT1022ACH is not interchangeable with a general-purpose precision amplifier unless every electrical and mechanical requirement is matched. According to the Analog Devices LT1022 datasheet, its defining features include JFET input bias current of typically 50 pA at 70°C, typically 80 µV offset voltage, and an 8.5 MHz gain-bandwidth product. The TO-5 metal-can package and eight-lead pin arrangement must also be verified before replacement.
What is the best Analog Devices equivalent for LT1022ACH?
An exact Analog Devices equivalent cannot be confirmed without a device-specific pin, package, and parameter comparison. The LT1022ACH combines a JFET input stage, typically 80 µV offset voltage, and a guaranteed minimum slew rate of 23 V/µs in an eight-lead TO-5 package. Use the Request a Quote form to request sourcing support, and treat any proposed equivalent as unapproved until its pinout, supply range, bias current, drift, and stability data are reviewed.

Data referensi kejuruteraan untuk LT1022ACH — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the LT1022ACH when a precision measurement requires very low input bias current, low offset voltage, and useful high-speed performance in a single eight-lead TO-5 package. It is particularly appropriate for photodiode amplifiers, high-impedance instrumentation, precision filters, low-level ADC drivers, and audio preamplifiers where source leakage would otherwise dominate the error. MC3403DR and LM2904PWR can serve broader general-purpose amplification tasks, but they are not pin-compatible replacements and their input bias characteristics are less suitable for very high source impedances. No verified drop-in alternative has been established for the LT1022ACH, so an existing TO-5 design should retain the original part unless a candidate has been checked against pin assignment, supply range, common-mode range, output swing, bias current, offset drift, stability, and environmental requirements.

Perbandingan dengan Gantian

Parametr Produk Ini
Brand Analog Devices
Package TO-5 metal can with 8 leads
Amplifier Type JFET-input operational amplifier
Typical Slew Rate 26 V/µs
Guaranteed Minimum Slew Rate 23 V/µs
Gain-Bandwidth Product 8.5 MHz
Typical Input Offset Voltage 80 µV
Maximum Input Offset Voltage 250 µV
Typical Input Offset Drift 1.5 µV/°C
Typical Input Bias Current at 70°C 50 pA
Maximum Input Bias Current at 125°C 4 nA
Output Load Current Capability 20 mA without gain degradation

Penyeberangsung Jelas

  • Very low JFET input bias current (vsMC3403DR)
  • Precision offset and thermal drift (vsLM2904PWR)
  • High speed with precision DC behavior (vsLM2904PWR)

Catatan Desain

Place the supply bypass capacitors as close as practical to the LT1022ACH power leads, with a short return path to the device ground connection. Keep high-impedance input and feedback traces away from the supply pins and other noisy conductors. Because the amplifier can operate with very low input bias current, contamination, solder residue, and surface leakage may become significant in high-gain transimpedance designs.

For photodiode or capacitive-source applications, evaluate the sensor capacitance together with the selected feedback resistor and compensation capacitor. The LT1022ACH provides an 8.5 MHz gain-bandwidth product and a guaranteed minimum slew rate of 23 V/µs, but those figures do not by themselves guarantee stability at every noise gain. Simulate the complete transimpedance network using the amplifier model corresponding to the intended operating conditions.

Do not interpret the low typical input bias current as a value that remains constant over the complete temperature range. Bias current increases to 500 pA typically and 4 nA maximum at 125°C. For high-value feedback networks, calculate the resulting error across the feedback impedance at the worst-case operating temperature and confirm that the input common-mode and output swing limits remain satisfied.

Use a stable mechanical and thermal design for the eight-lead TO-5 metal-can package. Keep sensitive input connections away from package leads carrying supply current and provide an appropriate ground-plane arrangement under the surrounding circuitry. For low-level instrumentation, verify thermal gradients across the board because they can cause offset-voltage drift even when the amplifier's specified maximum drift is not exceeded locally.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The operational amplifier is not marketed as an automotive-qualified AEC-Q100 device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the cited manufacturer or distributor material.

Data disahkan pada: 2026-11-14 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

LT1022ACH datasheet LT1022ACH datasheet pdf LT1022ACH pinout LT1022ACH TO-5 pinout Analog Devices LT1022ACH LT1022ACH 8.5MHz gain bandwidth LT1022ACH 26V/us slew rate LT1022ACH 50pA bias current LT1022ACH photodiode amplifier LT1022ACH precision op amp LT1022ACH equivalent LT1022ACH drop-in replacement LT1022ACH price LT1022ACH stock

Komponen dan Tanda berkaitan

Analog Devices LT1022 LT1022ACH JFET-input operational amplifier operational amplifier analog amplifier IC signal conditioning precision instrumentation gain-bandwidth product slew rate input offset voltage input offset drift input bias current TO-5 metal-can package eight-lead package through-hole package photodiode transimpedance amplifier precision active filter low-level ADC driver audio preamplifier surface leakage noise gain RoHS REACH
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ