LT1022ACH - High-Speed Precision JFET Op Amp | Analog Devices
MPN: LT1022ACH ✓ ActiveLT1022ACH Overview
A JFET-input operational amplifier is a voltage-amplifier IC whose input stage uses junction field-effect transistors. Within the semiconductor hierarchy, it belongs to the operational-amplifier family, analog amplifier ICs, and the broader signal-conditioning category. The JFET input stage provides very low bias current, while the precision amplifier architecture provides low offset voltage, low voltage drift, and stable operation over temperature.
Key performance characteristics include a typical slew rate of 26 V/µs and a guaranteed minimum of 23 V/µs. The device has an 8.5 MHz gain-bandwidth product, typical offset voltage of 80 µV, and maximum offset voltage of 250 µV. Input bias current is typically 50 pA at 70°C and 500 pA at 125°C, supporting high-impedance source applications. Output current capability is specified at 20 mA without gain degradation.
The precision of the LT1022ACH is supported by a typical input offset drift of 1.5 µV/°C and a maximum specified drift of 5 µV/°C. At elevated temperature, maximum offset voltage reaches 750 µV at 125°C. These characteristics make the amplifier suitable for closed-loop systems requiring accurate DC behavior while retaining useful high-speed response. The 8.5 MHz gain-bandwidth product supports moderately high closed-loop bandwidth, particularly at low noise gains.
Typical applications include precision test and measurement circuits, low-level sensor amplifiers, photodiode signal conditioning, precision active filters, audio preamplification, and low-level ADC input stages. The low bias current is particularly useful when driving high source impedances, while the 23 V/µs guaranteed minimum slew rate helps preserve large-signal response.
Designers should account for input bias-current temperature behavior and verify the selected feedback network against the amplifier's gain-bandwidth and stability characteristics. Decoupling capacitors should be placed close to the supply pins, and unused inputs must be biased within the input common-mode range to avoid saturation.
This product page combines manufacturer specifications, application-oriented engineering guidance, comparison criteria, and practical design notes for engineers evaluating the LT1022ACH as a precision, high-speed JFET-input amplifier.
Drop-in alternatives for LT1022ACH — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LT1022ACH (same form factor and footprint) — differing in Amplifier Type, Package.
No drop-in alternatives available for this product.
Request AlternativesLT1022ACH Maximum Ratings & Electrical Characteristics
| Amplifier Type | 1-circuit precision JFET-input operational amplifier |
| Typical Slew Rate | 26 V/µs |
| Guaranteed Minimum Slew Rate | 23 V/µs |
| Gain-Bandwidth Product | 8.5 MHz |
| Typical Input Offset Voltage | 80 µV |
| Maximum Input Offset Voltage | 250 µV |
| Maximum Input Offset Voltage at 125°C | 750 µV |
| Typical Input Offset Drift | 1.5 µV/°C |
| Maximum Input Offset Drift | 5 µV/°C |
| Typical Input Bias Current at 70°C | 50 pA |
| Typical Input Bias Current at 125°C | 500 pA |
| Maximum Input Bias Current at 70°C | 180 pA |
| Maximum Input Bias Current at 125°C | 4 nA |
| Output Load Current Capability | 20 mA without gain degradation |
| Package | TO-5 metal can with 8 leads |
| Mounting Type | Through-hole |
LT1022ACH to-5 metal can with 8 leads Pin Configuration Guide
Pin configuration for LT1022ACH (to-5 metal can with 8 leads package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for LT1022ACH.
Refer to the datasheet for full pin configuration.
Typical Applications
LT1022ACH is suitable for 6 applications: Precision Instrumentation Amplifier, Photodiode Signal Conditioning, Precision Active Filtering, Audio Preamplifier, Low-Level ADC Input Driver, Precision Buffer and Level Conditioning.
Precision Instrumentation Amplifier
The LT1022ACH fits low-level instrumentation circuits where the sensor or source resistance makes input bias current important. Its typical bias current of 50 pA at 70°C and 500 pA at 125°C limits leakage-induced error across high-value feedback resistors. The typically 80 µV offset voltage and 1.5 µV/°C drift support accurate DC measurements, while the 8.5 MHz gain-bandwidth product and 23 V/µs guaranteed minimum slew rate preserve response for signals that are not strictly static.
Photodiode Signal Conditioning
A transimpedance amplifier built around the LT1022ACH can benefit from its low JFET input bias current, which is typically 50 pA at 70°C. That characteristic helps preserve weak current signals from photodiodes without excessive error across a high-value feedback resistor. The 26 V/µs typical slew rate and 8.5 MHz gain-bandwidth product are useful for moderate-bandwidth optical measurements. Compensation capacitance, sensor capacitance, and amplifier noise gain must be evaluated together to maintain stability.
Precision Active Filtering
The LT1022ACH can serve as an active element in precision filter and signal-conditioning networks that combine high source impedance with moderate frequency requirements. Its low typical input bias current of 50 pA at 70°C reduces interaction with high-impedance stages, while the 8.5 MHz gain-bandwidth product provides useful closed-loop bandwidth. Offset drift is typically 1.5 µV/°C, but overall filter accuracy will still depend on resistor and capacitor tolerances, noise gain, and temperature stability.
Audio Preamplifier
The LT1022ACH suits low-level audio preamplification stages requiring low bias current and a faster response than a basic general-purpose amplifier. According to the Analog Devices LT1022 datasheet, it combines an 8.5 MHz gain-bandwidth product with a typical slew rate of 26 V/µs. The low offset voltage and drift reduce DC movement at the signal path, while the JFET input stage is compatible with high-impedance transducers. Headroom and output-swing limits must be checked against the required signal level.
Low-Level ADC Input Driver
The LT1022ACH can drive the input of a high-resolution ADC when the source presents a substantial impedance and the converter requires a low-noise, accurate drive signal. The amplifier's typically 50 pA input bias current at 70°C helps reduce errors associated with source leakage and sampling-network charging. Its 8.5 MHz gain-bandwidth product supports moderate-bandwidth conversion systems, although the final settling time must be compared with the ADC acquisition requirements and sampling capacitor.
Precision Buffer and Level Conditioning
The LT1022ACH is useful as a precision buffer when a high-impedance source cannot drive the next stage directly and conventional amplifier input bias current would disturb the signal. Its typical 80 µV offset voltage, 1.5 µV/°C drift, and low JFET input bias current preserve small DC signals. The 20 mA load-current capability without gain degradation supports moderate output loading. Confirm the common-mode range and output swing against the source and destination signal levels in the final circuit.
Engineering reference data for LT1022ACH — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Brand | Analog Devices |
| Package | TO-5 metal can with 8 leads |
| Amplifier Type | JFET-input operational amplifier |
| Typical Slew Rate | 26 V/µs |
| Guaranteed Minimum Slew Rate | 23 V/µs |
| Gain-Bandwidth Product | 8.5 MHz |
| Typical Input Offset Voltage | 80 µV |
| Maximum Input Offset Voltage | 250 µV |
| Typical Input Offset Drift | 1.5 µV/°C |
| Typical Input Bias Current at 70°C | 50 pA |
| Maximum Input Bias Current at 125°C | 4 nA |
| Output Load Current Capability | 20 mA without gain degradation |
Key Differentiators
- Very low JFET input bias current (vs MC3403DR)
- Precision offset and thermal drift (vs LM2904PWR)
- High speed with precision DC behavior (vs LM2904PWR)
Design Notes
Place the supply bypass capacitors as close as practical to the LT1022ACH power leads, with a short return path to the device ground connection. Keep high-impedance input and feedback traces away from the supply pins and other noisy conductors. Because the amplifier can operate with very low input bias current, contamination, solder residue, and surface leakage may become significant in high-gain transimpedance designs.
For photodiode or capacitive-source applications, evaluate the sensor capacitance together with the selected feedback resistor and compensation capacitor. The LT1022ACH provides an 8.5 MHz gain-bandwidth product and a guaranteed minimum slew rate of 23 V/µs, but those figures do not by themselves guarantee stability at every noise gain. Simulate the complete transimpedance network using the amplifier model corresponding to the intended operating conditions.
Do not interpret the low typical input bias current as a value that remains constant over the complete temperature range. Bias current increases to 500 pA typically and 4 nA maximum at 125°C. For high-value feedback networks, calculate the resulting error across the feedback impedance at the worst-case operating temperature and confirm that the input common-mode and output swing limits remain satisfied.
Use a stable mechanical and thermal design for the eight-lead TO-5 metal-can package. Keep sensitive input connections away from package leads carrying supply current and provide an appropriate ground-plane arrangement under the surrounding circuitry. For low-level instrumentation, verify thermal gradients across the board because they can cause offset-voltage drift even when the amplifier's specified maximum drift is not exceeded locally.
Compliance Information
The operational amplifier is not marketed as an automotive-qualified AEC-Q100 device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the cited manufacturer or distributor material.