LT1057CJ8 - Dual JFET Precision High-Speed Op Amp | Analog Devices
MPN: LT1057CJ8 ✓ AktifLT1057CJ8 Ringkasan
An operational amplifier is an analog signal-conditioning integrated circuit that amplifies the voltage difference between its two inputs while providing high open-loop gain and low output impedance. The JFET-input topology places the LT1057 in the amplifier hierarchy as a precision analog IC with high input impedance and low input bias current. This makes it particularly useful when a low-level sensor or instrumentation signal must be amplified without loading its source.
The LT1057's principal performance features include a typical slew rate of 14 V/µs, a guaranteed minimum of 10 V/µs, a minimum 5 MHz gain-bandwidth product, and fast settling to within 0.02%. Its maximum offset voltage is 450 µV for the LT1057, compared with 180 µV for the closely related LT1058 in the same dual-and-quad JFET-input family. These specifications support accurate, high-frequency signal amplification when component selection and layout are guided by the manufacturer datasheet.
Architecturally, the LT1057 is a matched dual amplifier, meaning that its two channels are designed for closely matched performance. JFET input devices are valued for high input impedance and low input bias current, while the high gain-bandwidth product supports wider closed-loop bandwidth than a conventional precision-only amplifier. The 8-pin configuration supports common industry-standard dual-op-amp layouts and reduces the need for a custom footprint when the exact package matches.
Typical uses include low-level instrumentation, precision signal conditioning, audio and communications circuitry, active filters, and general-purpose high-speed analog amplification. It is also appropriate for laboratory and industrial signal-chain designs that benefit from matched dual channels, such as differential amplifiers, balanced input stages, and dual-channel filters. Package choice, supply voltage, input common-mode range, output swing, and stability requirements must be checked against the datasheet for the selected grade and temperature range.
When laying out an LT1057CJ8 circuit, use a solid ground plane, minimize input-node capacitance, and place input and feedback components close to the associated amplifier pins. Because high-speed devices can amplify unintended feedback paths, keep output and input routing separate and observe the documented compensation recommendations for the required closed-loop gain. Through-hole ceramic-DIP construction is useful for prototyping and legacy-compatible industrial assemblies, but it occupies more board area than a surface-mount dual op amp.
This product page combines the manufacturer's functional description with package identification, key speed, bandwidth, settling, and offset specifications, practical design guidance, and qualified cross-reference options. It also distinguishes the dual LT1057 from the related quad LT1058 and evaluates the manufacturer's identified upgrades over LF412A and OP-215 dual JFET-input amplifier designs.
Pilihan pengganti yang segera untuk LT1057CJ8 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Tiada pilihan pengganti yang segera untuk produk ini.
Minta AlternatifLT1057CJ8 Penilaian maksimum & Ciri-ciri Elektrik
| Amplifier Type | Matched dual JFET-input operational amplifier |
| Number of Channels | 2 channels |
| Typical Slew Rate | 14 V/µs |
| Minimum Slew Rate | 10 V/µs |
| Minimum Gain-Bandwidth Product | 5 MHz |
| Settling Accuracy | 0.02% |
| Maximum Offset Voltage | 450 µV for LT1057 |
| LT1058 Maximum Offset Voltage | 180 µV |
| Input Transistor Type | JFET |
| Kemasan | 8-pin CERDIP |
| Kiraan Pin | 8 pins |
| Jenis Pemasangan | Through-hole |
| Temperature Grade | Commercial |
Panduan Konfigurasi Pin LT1057CJ8 8-pin cerdip
Konfigurasi pin untuk LT1057CJ8 (8-pin cerdip pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk LT1057CJ8.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
LT1057CJ8 patut untuk 6 aplikasis: Precision Instrumentation Amplification, Active Filter and Frequency Response Design, Audio and Communications Signal Conditioning, Data Acquisition Front End, Industrial Control and Process Measurement, Test and Measurement Equipment.
Precision Instrumentation Amplification
The LT1057CJ8 fits low-level instrumentation front ends that require a JFET input, low input bias current, and more bandwidth than a conventional precision-only dual amplifier. Its 14 V/µs typical slew rate and 5 MHz minimum gain-bandwidth product allow the closed-loop amplifier to follow sensor signals with less slew limitation than slower precision op amps. The two matched channels can also implement balanced differential stages, active filters, or instrumentation blocks. Because the 8-pin ceramic-DIP package is through-hole, it is especially practical for laboratory prototypes, test equipment, and industrial control assemblies where serviceability and socketed construction are useful.
Disebarkan
Active Filter and Frequency Response Design
The LT1057CJ8 is appropriate for active filters and closed-loop response stages where the 5 MHz minimum gain-bandwidth product and 0.02% settling target can improve useful signal bandwidth and transient response. Its JFET input helps avoid excessive loading of the preceding filter or sensor node, while the dual configuration supports two poles, a differential filter, or a two-channel equalizer without requiring four separate packages. Component tolerances and op-amp gain-bandwidth behavior remain central to the final response, so simulation should include the selected external resistors and capacitors. The manufacturer family datasheet's typical circuits provide a useful starting point for stable compensation and gain selection.
Disebarkan
Audio and Communications Signal Conditioning
The LT1057CJ8 can be used in audio and communications signal-conditioning paths that benefit from fast settling and a JFET input stage. A typical circuit would amplify a low-level source, apply active equalization, or provide drive into a subsequent conversion stage. The 14 V/µs typical slew rate helps preserve larger-amplitude transients, while the minimum 5 MHz gain-bandwidth product supports closed-loop bandwidth beyond the range of a precision-only op amp. Designers should still check the required supply, output swing, noise, and channel-matching specifications, and should decouple each supply rail close to the device pins.
Disebarkan
Data Acquisition Front End
The LT1057CJ8 is suitable for conditioning inputs in moderate-speed data-acquisition systems where sensor loading must remain low and amplifier settling affects subsequent sampling accuracy. Its JFET input is well matched to high-impedance sources, while the 5 MHz minimum gain-bandwidth product and fast 0.02% settling target support wider-band signal chains than conventional precision dual op amps. The dual amplifier can implement a differential input stage or two matched channels. For a production acquisition design, compare the exact input common-mode range, offset, bias current, noise, and supply limits before selecting the ceramic-DIP grade and operating temperature range.
Disebarkan
Industrial Control and Process Measurement
The LT1057CJ8 can amplify low-level process signals in industrial measurement equipment where the through-hole ceramic-DIP package supports serviceable assemblies and the JFET input minimizes loading of high-impedance sensors. Its 14 V/µs typical slew rate and 5 MHz minimum gain-bandwidth product provide useful response for dynamic measurements beyond what a slow precision amplifier can handle. The matched dual channels may be used for differential sensing or independent signal paths with similar performance. The final circuit must account for industrial supply tolerances, grounding, common-mode limits, thermal conditions, and the manufacturer's documented stability requirements at the intended closed-loop gain.
Disebarkan
Test and Measurement Equipment
The LT1057CJ8 is a practical choice for test and measurement equipment requiring a matched dual amplifier with fast large-signal response. It can form buffer, gain, active-filter, or driver stages for laboratory instruments while its JFET input preserves the behavior of high-impedance probes or sensors. The 5 MHz minimum gain-bandwidth product supports higher-frequency response than a conventional precision-only op amp, and the dual architecture helps minimize channel-to-channel design variation in paired measurements. Through-hole ceramic-DIP construction is convenient for prototypes, socketed modules, and serviceable instruments. Layout should minimize feedback-loop area and maintain a low-impedance ground reference to preserve the intended settling behavior.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk LT1057CJ8 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini |
|---|---|
| Package | 8-pin CERDIP |
| Brand | Analog Devices |
| Amplifier Configuration | Dual |
| Input Type | JFET |
| Typical Slew Rate | 14 V/µs |
| Minimum Slew Rate | 10 V/µs |
| Minimum Gain-Bandwidth Product | 5 MHz |
| Settling Accuracy | 0.02% |
| Maximum Offset Voltage | 450 µV for LT1057 |
| Mounting Type | Through-hole |
| Temperature Grade | Commercial |
| Price Tier | Request a Quote |
Penyeberangsung Jelas
- Combines JFET input with high-speed performance (vsLF412A)
- Fast settling suitable for precision signal paths (vsOP-215)
- Matched dual-channel architecture in an 8-pin ceramic DIP (vsLT1058)
Catatan Desain
Place input, feedback, and compensation components close to their associated LT1057CJ8 pins, and use a continuous ground plane to minimize parasitic inductance. Keep the output node away from high-impedance input traces because the device's 14 V/µs typical slew rate can expose feedback through unintended coupling. The ceramic-DIP footprint must also include adequate pin-1 clearance for the package identifier and should preserve socket or solder-joint access for serviceable through-hole assemblies.
Evaluate closed-loop stability at every intended gain because parasitic board and socket capacitance can reduce the phase margin of a high-speed amplifier. The manufacturer family datasheet includes typical application circuits and compensation guidance for the LT1057. When using the 8-pin ceramic-DIP in a socket, account for additional contact and lead inductance, and compare the assembled prototype against the simulation with short, symmetric feedback paths and a low-impedance reference plane.
Do not treat the LF412A and OP-215 names mentioned by Analog Devices as unconditional drop-in substitutes for the LT1057CJ8. Confirm the exact package, lead assignments, supply range, common-mode range, input bias current, offset voltage, output swing, and temperature grade. The ceramic-DIP suffix also identifies a commercial grade, so a replacement with the same amplifier family but a different grade or package may require PCB, qualification, or thermal changes.
Use a low-impedance bypass path for each supply connection and verify the selected supply voltage against the exact LT1057CJ8 operating limits. Decoupling capacitors should be placed at the device pins with short ground returns rather than at a remote power-entry point. Check the total power dissipation under the maximum expected load and ambient temperature, particularly in compact legacy-style assemblies where ceramic-DIP airflow may be limited.
Maklumat Kesediaan
The commercial-grade ceramic-DIP LT1057CJ8 is not presented as an automotive-qualified part. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not identified in the cited product information.