LT1632IS8 - 45MHz, 45V/us Dual RRIO Precision Op Amp | ADI
MPN: LT1632IS8 ✓ AktifLT1632IS8 Ringkasan
An operational amplifier is a high-gain differential amplifier whose key job is to condition a small voltage difference between its two inputs and deliver a scaled, low-distortion output. A rail-to-rail input stage means the common-mode input range extends to both supply rails, so the amplifier can sense signals that swing from ground to the positive rail; a rail-to-rail output stage means the output can also swing to within a few hundred millivolts of either rail. This dual capability places the LT1632 in the general-purpose amplifier family, above precision instrumentation amplifiers and inside the broader analog signal-chain IC hierarchy.
The headline specifications are a 45 MHz gain-bandwidth product, which sets the small-signal speed ceiling, and a 45 V/us slew rate, which sets the large-signal speed ceiling. Because the two numbers are matched, the LT1632 preserves near-full bandwidth well into the high-gain region, so a 10 V step is reproduced without the extended settling times typical of unity-gain-stable, slew-limited amplifiers. Supply operation reaches plus or minus 15 V, giving a 30 V total span, and the 8-pin SO package keeps the footprint compatible with conventional dual op amp layouts.
Internally the LT1632 is built on a precision, low-noise process with a fully differential input stage and a class-AB output stage that keeps distortion low at low signal levels while still delivering high bandwidth. Rail-to-rail input is achieved without the input-offset degradation typical of simple complementary-bipolar input stages, and the output stage is designed to remain stable into the wide range of capacitive loads encountered in filtering and cable driving. The result is an amplifier that behaves like a precision part in DC terms and like a high-speed part in AC terms.
Typical uses include buffering precision ADC front ends, driving instrumentation and audio DAC input stages, active filters with high slew-rate demand, and low-noise sensor signal conditioning where the full common-mode range of the supply is needed. Two independent channels in one package also reduce board area in multi-axis sensor systems and in stereo or differential signal conditioning paths.
When laying out the board, treat the SOIC-8 footprint of the LT1632IS8 as interchangeable with any standard dual op amp: stable reference pins, decoupling close to the supply pins, and a clean ground return matter more than exotic routing. Because the device is a precision part, verify input common-mode range against the actual rail voltage in single-supply designs before committing to the design.
This page consolidates the manufacturer product data, distributor availability and package details with drop-in alternatives, an application-by-application fit analysis and practical design notes that are not found in a single location in the original datasheet.
Pilihan pengganti yang segera untuk LT1632IS8 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
LT1632CS8
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LT1632IS8#PBF
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LT1632IS8#TR
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LT1632IS8 Penilaian maksimum & Ciri-ciri Elektrik
| Number of Amplifiers | 2 (dual) |
| Gain-Bandwidth Product | 45 MHz |
| Slew Rate | 45 V/us |
| Input Type | Rail-to-Rail Input |
| Jenis Output | Rail-to-Rail Output |
| Supply Voltage Range | ±15 V (30 V total) |
| Kemasan | 8-pin SO (SOIC-8), 1.75 mm height |
| Bilangan Pin | 8 |
| Jenis Pemasangan | Surface Mount |
| Suhu Operasi | -40 °C to +85 °C (industrial grade, I suffix) |
| Production Status | PRODUCTION (per manufacturer product page) |
| AEC-Q100 Qualification | Not applicable (industrial-grade analog amplifier) |
Konfigurasi Pin LT1632IS8
| Pin 1 | OUT A — Output of amplifier A |
| Pin 2 | -IN A — Inverting input of amplifier A |
| Pin 3 | +IN A — Non-inverting input of amplifier A |
| Pin 4 | V- — Negative supply pin |
| Pin 5 | +IN B — Non-inverting input of amplifier B |
| Pin 6 | -IN B — Inverting input of amplifier B |
| Pin 7 | OUT B — Output of amplifier B |
| Pin 8 | V+ — Positive supply pin |
Aplikasi Biasa
LT1632IS8 patut untuk 6 aplikasis: Precision ADC Signal Conditioning, Active Filter and Equalizer Design, Audio and Instrumentation Signal Paths, Sensor Signal Conditioning, Power Supply Feedback and Control Loops, Test and Measurement Instrumentation.
Precision ADC Signal Conditioning
The LT1632IS8 sits in front of high-resolution converters as a rail-to-rail input/output buffer and driver. With a 45 MHz gain-bandwidth product and 45 V/us slew rate, it can settle a full-scale step quickly enough that the amplifier does not limit converter acquisition time, while rail-to-rail input accepts sensor signals that swing close to either supply rail. Use it as a unity-gain buffer in front of the converter input, add a small isolation resistor when the ADC presents a large sampling capacitor, and keep the layout short so that 45 MHz of bandwidth does not pick up board noise. The trade-off against a slower general-purpose dual op amp is negligible at low frequency but decisive at high converter rates.
Disebarkan
Active Filter and Equalizer Design
Cascaded biquad sections built from the LT1632IS8 retain useful bandwidth well above the cutoff frequency because the 45 MHz gain-bandwidth product is matched to the 45 V/us slew rate. This matters for filters where large-signal steps - filter reconfiguration, input transient, or a full-scale sine at the output - would otherwise dominate the error budget and slow settling. Build higher-order filters with one dual package, one channel per section, and take advantage of the rail-to-rail input and output to operate from a single low-voltage supply where the signal occupies most of the available range. Keep the gain per section moderate so the closed-loop noise gain does not eat the bandwidth advantage.
Disebarkan
Audio and Instrumentation Signal Paths
The LT1632IS8 is used where audio-band or instrumentation signals need low distortion and wide headroom: line-level buffers, headphone-driver front ends, and audio ADC input stages. A 45 V/us slew rate keeps large-signal distortion low at frequencies where the 45 MHz gain-bandwidth product still provides gain, and rail-to-rail output allows near-full use of the available supply swing, which is critical in battery and headphone-capable designs. Pair it with a clean reference and short, shielded input routing to preserve the noise performance the wide bandwidth provides. The trade-off is that a fast amplifier in a feedback loop demands careful grounding, so keep the ground return short and decouple each supply pin locally.
Disebarkan
Sensor Signal Conditioning
Bridge, thermocouple and strain-gauge front ends benefit from the LT1632IS8 because the rail-to-rail input stage accepts sensor outputs that sit close to the negative rail, a common condition when the sensor is powered from a single supply referenced to ground. The 45 MHz bandwidth makes the amplifier usable both as a DC-level instrumentation buffer and as a wideband path for dynamic sensor outputs. Use the two channels for gain and filtering in a three-op-amp instrumentation topology, keeping the resistor network matched and placed close to the inputs. Because wideband amplifiers can pick up radiated noise, keep the gain bandwidth product in mind when sizing the first filter pole and avoid placing long traces next to switching regulators.
Disebarkan
Power Supply Feedback and Control Loops
The LT1632IS8 is used as the error amplifier in voltage-mode control loops and as a buffer for a remote or high-impedance feedback node, where the rail-to-rail input and output let the loop sense and drive signals close to the rails without a separate bias network. The 45 V/us slew rate keeps loop dynamics well controlled even with significant output filter capacitance, and the 45 MHz gain-bandwidth product allows loops with crossover well above the audible range. Place the amplifier close to the feedback divider to minimize parasitic pickup, and remember that a fast error amplifier will amplify any noise picked up on the feedback trace, so keep feedback routing short and shield it from switching nodes.
Disebarkan
Test and Measurement Instrumentation
Laboratory and factory test equipment uses the LT1632IS8 in driver and buffer paths where the measured signal must be reproduced faithfully at frequencies well beyond the audio band. The combination of rail-to-rail operation, 45 MHz bandwidth and 45 V/us slew rate covers a wide range of source impedances and load conditions without the distortion that a slower precision amplifier introduces when driving a terminated input. Use the two channels of one package for complementary or differential buffering to reduce board area in multi-channel fixtures. Because the amplifier is so fast, verify that the surrounding fixture cables and connectors do not become the limiting element, and terminate unused channels to avoid oscillation.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk LT1632IS8 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | LT1632CS8 | LT1632IS8#PBF | LT1632IS8#TR |
|---|---|---|---|---|
| Package | 8-pin SO (SOIC-8) | 8-pin SO (SOIC-8) - same | 8-pin SO (SOIC-8) - same | 8-pin SO (SOIC-8) - same |
| Brand | Analog Devices (Linear Technology) | Analog Devices (Linear Technology) | Analog Devices (Linear Technology) | Analog Devices (Linear Technology) |
| Number of Amplifiers | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) |
| Gain-Bandwidth Product | 45 MHz | 45 MHz | 45 MHz | 45 MHz |
| Slew Rate | 45 V/us | 45 V/us | 45 V/us | 45 V/us |
| Input / Output Type | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
| Supply Voltage Range | ±15 V (30 V total) | ±15 V (30 V total) | ±15 V (30 V total) | ±15 V (30 V total) |
| Operating Temperature | -40 °C to +85 °C | Commercial grade (narrower than industrial) | -40 °C to +85 °C | -40 °C to +85 °C |
| Order Code / Packaging | IS8 - standard industrial order code | CS8 - commercial temperature order code | Lead-free marked order code | Tape-and-reel order code |
Penyeberangsung Jelas
- Speed headroom over classic general-purpose dual precision op amps (vsLT1632CS8)
- Industrial temperature coverage while keeping the same 8-pin SO footprint (vsLT1632CS8)
- Fully rail-to-rail input and output for single-supply signal chains (vsLT1632IS8#PBF)
- Order-code flexibility for lead-free marking and reel packaging (vsLT1632IS8#TR)
Catatan Desain
The LT1632IS8 uses the standard 8-pin dual op amp SOIC footprint, so the land pattern is shared with virtually any general-purpose dual amplifier. Keep the supply decoupling capacitor within a few millimetres of pins 4 and 8, route V+ and V- on a quiet path away from switching nodes, and place the feedback resistors close to the input pins so that parasitic capacitance does not destabilise the 45 MHz gain-bandwidth product. Note that the exposed bottom of a standard SOIC-8 has no thermal pad, so thermal relief is limited to the leads and the copper pour around them.
With a 45 V/us slew rate, the LT1632IS8 can drive capacitive loads that slower precision amplifiers handle comfortably, so check the capacitive load recommendations in the manufacturer data sheet before connecting it directly to a long cable, a high-impedance node or an ADC sampling network. A common failure is oscillation at the output followed by a saturated amplifier; the standard cures are an isolation resistor of a few tens of ohms at the output, a small feedback capacitance across the feedback resistor, and avoiding a capacitive probe at the output node.
Rail-to-rail input stages on this amplifier accept common-mode voltages right up to the supply rails, which is a benefit in single-supply designs but means the input pins can be exposed to clamp currents if the signal exceeds the rail. Confirm the input common-mode range against the actual rail voltage in your design, and never connect a signal source that can swing outside the supply without protection. Because the gain-bandwidth product is high, keep input traces short and away from the output node to prevent parasitic feedback through board coupling.
Operating from plus or minus 15 V gives the LT1632IS8 a 30 V total supply span, but real boards rarely deliver a clean ±15 V; unregulated rails can overshoot at light load. Keep the supply within the absolute maximum ratings in the data sheet, and remember that the slew rate, not the quiescent current, determines the dynamic behaviour of the output stage. For dual-supply designs, use separate bulk and ceramic decoupling on each rail, since a shared return path between the two rails injects supply ripple directly into the output.
Maklumat Kesediaan
Analog Devices offers lead-free order codes for this device family (LT1632IS8#PBF) alongside the standard LT1632IS8 order code; no explicit RoHS, REACH, halogen-free or conflict-minerals statement is published on the product listing. The device is an industrial-grade analog amplifier and is not presented as AEC-Q100 qualified.