MAX232ECWE+T - 5V RS-232 Transceiver, 120kbps | Analog Devices
MPN: MAX232ECWE+T ✓ AktifMAX232ECWE+T Ringkasan
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 differential voltage levels and converts incoming RS-232 signals back into logic-compatible levels. It belongs to the interface IC hierarchy, where transceivers connect modern digital systems to older, noise-tolerant serial ports. The MAX232ECWE+T is intended for EIA/TIA-232E and CCITT V.28 communication links operating from a single 5V rail.
The integrated charge pump eliminates the need for a separate negative supply, allowing the MAX232ECWE+T to operate from 4.5V to 5.5V. Its two transmit channels provide full-duplex serial communication, while two receive channels support simultaneous bidirectional data exchange. The ±15kV human-body-model ESD protection improves tolerance when users, cables, or external equipment connect to the communication port.
As a CMOS interface device, the MAX232ECWE+T combines low-power 5V operation with level translation between TTL-compatible circuitry and RS-232. Internal transmitter and receiver functions implement the voltage conversion required at the physical interface, while the charge-pump section supports the bipolar signal levels used by compliant RS-232 equipment. The 16-pin SOIC package supports conventional surface-mount assembly and standard board-level inspection.
Typical uses include industrial equipment serial ports, laboratory instrumentation, point-of-sale terminals, embedded control systems, and service-console connections. The device is especially useful where the host electronics have a 5V supply and the connected peripheral expects a physical RS-232 port rather than USB or a low-voltage differential interface. Cable protection and grounding remain important when connecting the transceiver to long or electrically noisy external cables.
For a new design, place the required charge-pump capacitors close to their associated pins and route each driver output directly toward its connector. Keep logic-side traces away from RS-232 line outputs, provide a solid ground return, and select external protection appropriate to the cable environment. Review the device's operating-temperature grade and absolute-maximum limits before using it outside a commercial-temperature enclosure.
This page combines the verified MAX232ECWE+T interface specifications, same-package cross-reference options, application guidance, and a parameter comparison that helps engineers distinguish electrical, package, and grade differences before approving a substitution.
Pilihan pengganti yang segera untuk MAX232ECWE+T — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MAX232ECWE+T (sama faktor bentuk dan kaki) — berbeza dalam Product Type, Package, ESD Protection, Interface Standard, Mounting Type.
MAX232EEWE+T
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MAX232ECDWR
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MAX232EESE+
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →MAX232EWE+T
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MAX232ECWE+T Spesifikasi
| Product Type | Dual RS-232 transceiver |
| Number of Drivers | 2 drivers |
| Number of Receivers | 2 receivers |
| Duplex Mode | Full duplex |
| Kadar Data | 120kbps |
| Supply Voltage Range | 4.5V to 5.5V |
| Nominal Supply Voltage | +5V |
| ESD Protection | ±15kV HBM |
| Interface Standard | EIA/TIA-232E |
| Interface Standard | CCITT V.28 |
| Kemasan | 16-pin SOIC |
| Jenis Pemasangan | Surface mount |
| Charge Pump | Integrated |
Panduan Konfigurasi Pin MAX232ECWE+T 16-pin soic
Konfigurasi pin untuk MAX232ECWE+T (16-pin soic pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk MAX232ECWE+T.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
MAX232ECWE+T patut untuk 6 aplikasis: Industrial Serial Equipment Interface, Point-of-Sale Terminal Connection, Laboratory Instrument Control Port, Embedded Service Console, Security and Access-Control Head End, Data Acquisition and Control Module.
Industrial Serial Equipment Interface
The MAX232ECWE+T is appropriate for legacy industrial equipment that exposes a physical RS-232 port from a 5V controller. Its two transmitters and two receivers support full-duplex communication, while the 120kbps rating covers common serial-console and machine-control protocols. The integrated charge pump removes the need for a separate negative supply, simplifying the interface power architecture. Place the driver outputs and receiver inputs near the connector and use the device data sheet to select the charge-pump capacitors. The main engineering consideration is cable behavior: long industrial runs can pick up noise, so maintain a low-impedance ground return and evaluate external surge protection when the port is exposed to uncontrolled cabling.
Disebarkan
Point-of-Sale Terminal Connection
The MAX232ECWE+T provides a compact RS-232 link between a 5V embedded controller and a point-of-sale terminal. Full-duplex operation permits command requests and transaction responses to share the cable when the peripheral implements both directions. Its 120kbps data rate is suitable for many peripheral protocols, and ±15kV HBM protection adds resilience at a connector that users may service. Keep the logic interface and charge-pump components away from the exposed cable side of the board. Confirm the peripheral's RS-232 pinout and logic levels before wiring because DTE and DCE equipment may assign the same connector signals differently. The data-sheet input thresholds should also be checked if the cable is unusually long.
Disebarkan
Laboratory Instrument Control Port
The MAX232ECWE+T can connect a laboratory controller or embedded test platform to an RS-232-equipped instrument. The dual transmitter and dual receiver arrangement supports bidirectional command and measurement traffic, while 120kbps is appropriate for many legacy instrument-control protocols. A single 5V rail simplifies integration with modern controller boards, and the integrated charge pump avoids a discrete negative-voltage supply. Route the RS-232 traces as a paired signal and ground path, keep them separate from sensitive analog inputs, and verify the instrument's handshake behavior. Instrument cables can be long and connect to noisy laboratory equipment, so grounding and connector-level protection deserve attention even though the transceiver includes ±15kV HBM ESD protection.
Disebarkan
Embedded Service Console
The MAX232ECWE+T is useful for an embedded service or maintenance console because it provides standard RS-232 levels from a 5V system while preserving two full-duplex channels. The 120kbps ceiling matches common diagnostic protocols, and the SOIC package allows placement near a board-edge connector without requiring a through-hole interface. Route the two receive lines away from switching-power nodes and high-current return paths because the transmitter outputs can be several volts beyond logic levels. Use a common ground between the controller and connected equipment, and keep cable exposure away from sources of electromagnetic interference. If the service port must tolerate frequent plugging or severe industrial transients, add appropriate connector and surge-protection hardware.
Disebarkan
Security and Access-Control Head End
The MAX232ECWE+T can provide the physical communication path between a 5V access-control head end and an RS-232 peripheral. Bidirectional channels allow the controller to exchange authorization or configuration data, while ±15kV HBM protection is valuable at an accessible connector. The 120kbps rate is more than adequate for typical configuration and status traffic. Place a common-mode choke or selected series damping network where cable-emitted transients are a concern, and verify that the peripheral uses conventional RS-232 rather than RS-485 electrical levels. Correct grounding and signal pairing are essential because RS-232 is a single-ended, unbalanced interface. The device's integrated charge pump also reduces system complexity compared with a discrete bipolar transmitter implementation.
Disebarkan
Data Acquisition and Control Module
The MAX232ECWE+T supports legacy RS-232 communication in a data-acquisition or process-control module. Two receivers can collect status or trigger information, and two transmitters can return commands or sampled data to an external controller. Its single 5V operation, integrated charge pump, and 120kbps full-duplex performance fit compact embedded control boards. The interface is most effective when the RS-232 lines are protected from the high-energy switching circuitry used by adjacent power stages. Separate logic and cable-side regions, maintain a continuous ground plane, and use controlled return paths for both receive channels. If the module must tolerate long cables or repeated electrical surges, specify external protection and validate the complete assembled channel rather than relying only on the transceiver's internal ESD rating.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MAX232ECWE+T — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MAX232EEWE+T | MAX232ECDWR | MAX232EESE+ | MAX232EWE+T |
|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC - same | 16-SOIC - same | 16-SOIC - same | 16-SOIC - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Type | Dual RS-232 transceiver | RS-232 interface IC | Dual RS-232 transceiver | Dual RS-232 transceiver | RS-232 interface IC |
| Number of Drivers | 2 drivers | 2 drivers | 2 drivers | 2 drivers | 2 drivers |
| Number of Receivers | 2 receivers | 2 receivers | 2 receivers | 2 receivers | 2 receivers |
| Duplex Mode | Full duplex | Full duplex | Full duplex | Full duplex | Full duplex |
| Interface Standards | EIA/TIA-232E and CCITT V.28 | RS-232 interface | RS-232 interface | RS-232 interface | RS-232 interface |
Penyeberangsung Jelas
- Data rate matches a conventional 120kbps RS-232 interface (vsMAX232EWE+T)
- Single 5V implementation with integrated charge pump (vsMAX232ECDWR)
- Full-duplex interface with two transmit and two receive channels (vsMAX232EEWE+T)
- Integrated ±15kV HBM ESD protection (vsMAX232EESE+)
Catatan Desain
Place the charge-pump capacitors close to their designated MAX232ECWE+T pins and use the exact capacitance and voltage rating specified in the manufacturer data sheet. Keep the capacitor loops compact because high-frequency charge-pump current circulates through these traces. Route RS-232 outputs toward the connector without passing beneath sensitive analog or receive-input traces, and provide a continuous ground reference between the transceiver and connector.
Separate the cable-side RS-232 region from switching regulators, relays, motor drivers, and high-current power paths. Although the receiver rejects some common-mode noise, it cannot compensate for excessive cable pickup. Keep the two receiver traces away from the driver outputs, use a solid uninterrupted ground plane, and route cable returns directly to the interface ground reference. These measures are particularly important when the external cable is long or the enclosure contains substantial power-conversion circuitry.
Do not assume that every 16-pin MAX232-family suffix is an automatic replacement. Compare data rate, temperature grade, receiver thresholds, charge-pump capacitor requirements, and exposed-pin details. The MAX232EWE+T is identified as a 200kbps device, while the MAX232ECWE+T is rated for 120kbps. Also verify DTE versus DCE signal assignments at the connector because the transceiver does not determine the cable's application-side pinout.
For cables longer than several metres, consider series damping or a cable-side protection network that is selected for the required data rate and impedance. The transceiver's ±15kV HBM ESD rating addresses electrostatic discharge, not every lightning, industrial surge, or prolonged overload condition. Validate the complete interface under the intended cable length, grounding arrangement, and electromagnetic environment so that protection components do not distort the RS-232 signal excessively.
Maklumat Kesediaan
The device is an industrial or commercial RS-232 interface IC rather than an automotive-qualified component. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation in the manufacturer or distributor compliance records.