MAX310EPE+ - 8:1 CMOS RF Video Multiplexer | Analog Devices
MPN: MAX310EPE+ ✓ AktifMAX310EPE+ Ringkasan
A video multiplexer is an interface IC that connects multiple signal sources to one destination while allowing a controller to select the active channel. The MAX310 family belongs to the broader switching and multiplexing hierarchy, where analog switches and multiplexers route RF, video, or instrumentation signals without requiring duplicated receiver chains. The MAX310EPE+ uses CMOS circuitry and provides eight selectable inputs rather than acting as a general-purpose logic switch.
The main defining characteristics are its 8:1 multiplexing ratio, eight channels, CMOS implementation, and 16-pin PDIP package. The unbuffered architecture listed for this device is suitable for routing applications where impedance matching, gain, and signal-level compatibility are handled by the surrounding circuit. It is particularly relevant to video routing, RF signal selection, test and measurement systems, and legacy video equipment that uses through-hole construction.
Because the MAX310EPE+ is designed around an analog switching function, system performance depends on the source impedance, load impedance, signal amplitude, selected channel, and frequency being routed. The device should be evaluated in the complete signal path rather than by switching state alone. PCB routing, grounding, connector geometry, and control-signal timing can materially affect isolation, insertion loss, crosstalk, and signal integrity in high-frequency video systems.
Typical uses include video-source selection in test equipment, routing among multiple RF channels in instrumentation, channel selection in professional video equipment, and embedded analog switching systems. For new designs, engineers should confirm the supported signal frequency, on-resistance, bandwidth, off-isolation, and supply requirements against the current manufacturer datasheet before fixing the board architecture.
Designers should preserve the manufacturer's recommended supply decoupling and provide a low-impedance ground reference close to the device. Control inputs should be driven cleanly and sequenced so that channel changes do not create transient disturbances on sensitive downstream circuitry. Keep analog routing paths short, isolate switching return currents from precision references, and test all channels across the intended operating range.
This page organizes the MAX310EPE+ product identity, package information, sourcing fields, replacement analysis, application guidance, and engineering selection criteria in one concise reference. It also highlights where engineers must validate frequency, voltage, current, and channel performance in the manufacturer datasheet before releasing a production design.
Pilihan pengganti yang segera untuk MAX310EPE+ — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
MAX310CPE+
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MAX310EPE+ Spesifikasi
| Multiplexer Configuration | 8:1 ratio |
| Number of Channels | 8 channels |
| Signal Type | RF and video |
| Architecture | Unbuffered |
| Process Technology | CMOS |
| Package Type | PDIP-16 |
| Bilangan Pin | 16 pins |
| Jenis Pemasangan | Through-hole |
| Production Status | Production |
| Manufacturer | Analog Devices / Maxim Integrated |
Panduan Konfigurasi Pin MAX310EPE+ pdip-16
Konfigurasi pin untuk MAX310EPE+ (pdip-16 pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk MAX310EPE+.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
MAX310EPE+ patut untuk 6 aplikasis: Video Source Selection, RF Signal Routing, Test and Measurement Routing, Professional Video Equipment, Instrumentation Signal Selection, Industrial Control Signal Routing.
Video Source Selection
The MAX310EPE+ fits video-source selection because it provides eight RF or video inputs in an 8:1 multiplexing arrangement. Place the selected source on the common output path and drive the address or enable controls from the system controller. The unbuffered CMOS design allows the surrounding circuitry to define signal gain and impedance, but engineers must verify video bandwidth, crosstalk, off-isolation, and output loading against the manufacturer datasheet before release.
Disebarkan
RF Signal Routing
The MAX310EPE+ can route one of eight RF-related signal paths into a shared receiver or measurement chain when its frequency and isolation characteristics satisfy the system requirements. Its 8:1 organization reduces duplicated front-end circuitry, while the unbuffered architecture leaves matching and amplification to the surrounding design. Validate high-frequency insertion loss, crosstalk, source impedance, and load impedance because those parameters determine whether the routing path meets the intended RF performance.
Disebarkan
Test and Measurement Routing
The MAX310EPE+ is suitable for selecting among eight instrument or test channels in a controlled analog switching system. The 8:1 architecture allows a common measurement chain to examine multiple inputs without eight complete receiver paths. Designers should minimize trace length, maintain a low-impedance ground, and verify channel repeatability and isolation. Because the mux is unbuffered, the test architecture must account for source and load impedance rather than treating the device as a general-purpose logic switch.
Disebarkan
Professional Video Equipment
The MAX310EPE+ supports professional video equipment that needs to choose among several RF or composite-video sources. Its eight-channel CMOS multiplexer can consolidate routing into a shared output stage, reducing the number of duplicated downstream buffers. The through-hole PDIP package also suits established industrial and broadcast-related equipment with larger through-hole PCB layouts. Confirm the supported video bandwidth, signal amplitude, connector impedance, and channel-switching behavior before integrating it into a new chassis.
Disebarkan
Instrumentation Signal Selection
The MAX310EPE+ can serve as the front-end channel selector for instrumentation that alternates between up to eight analog signals. A common output may feed an amplifier, converter, or measurement block, simplifying the board hierarchy while retaining individual channel selection. The unbuffered implementation makes impedance matching and gain distribution important design tasks. Validate offset behavior, crosstalk, bandwidth, and switching transients against the exact source impedances used in the final instrument.
Disebarkan
Industrial Control Signal Routing
The MAX310EPE+ can route low-bandwidth analog or control-related signals when a system requires eight selectable inputs and one shared destination. The 8:1 topology is useful in legacy industrial controllers where minimizing duplicated routing logic is important. Its PDIP package remains practical for through-hole assemblies and repairable industrial boards. Confirm supply voltage, signal-level limits, temperature range, and switching characteristics in the manufacturer datasheet before using the mux with feedback, safety-critical, or high-energy signals.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MAX310EPE+ — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MAX310CPE+ |
|---|---|---|
| Brand | Analog Devices / Maxim Integrated | Maxim Integrated |
| Package | PDIP-16 | PDIP-16 - same |
| Multiplexing Ratio | 8:1 | 8:1 |
| Number of Channels | 8 channels | 8 channels |
| Signal Type | RF and video | RF and video multiplexer |
Penyeberangsung Jelas
- Established 8-channel RF and video routing function (vsMAX310CPE+)
- Through-hole package for established PCB architectures (vsMAX310CPE+)
- Production-status alignment with the MAX310 platform (vsMAX310CPE+)
Catatan Desain
Keep the MAX310EPE+ ground and selected analog signal paths short and provide a continuous ground plane beneath the routing area. Place any required supply-decoupling capacitor close to the device power pins with a low-inductance connection. Avoid routing high-current return paths beneath the mux because shared return impedance can couple switching transients into the selected video or RF channel.
Design the unbuffered mux around the actual source and load impedances. Confirm on-resistance, bandwidth, off-isolation, crosstalk, and insertion loss in the manufacturer datasheet, then include connector and trace losses in the channel budget. If the source or load is not suitable for direct connection, add an appropriate buffer or matching network instead of forcing the mux to operate outside its intended operating region.
Do not substitute a MAX310 order code based only on the base family name. Verify the exact package, pin arrangement, temperature grade, production status, and electrical limits. A valid replacement must preserve the 16-pin PDIP footprint and meet the board's required supply, signal, and timing conditions; otherwise, the PCB and surrounding circuitry must be reconsidered.
Maklumat Kesediaan
The MAX310 is an interface IC rather than an automotive-qualified power device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation or declaration.