MAX3221IDBE4 - 250kbps Single RS-232 Transceiver | Texas Instruments
MPN: MAX3221IDBE4 ✓ AktifMAX3221IDBE4 Ringkasan
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 levels and converts received RS-232 levels back into logic levels. It belongs to the RS-232 transceiver class of interface ICs, with the broader hierarchy progressing from transceiver to interface controller, communication interface, and semiconductor. The MAX3221 integrates a dual charge-pump circuit with the driver and receiver, reducing the external component count required for a working RS-232 port.
The 3 V to 5.5 V supply range allows operation in systems powered from 3.3 V or 5 V rails. Its 250 kbps data-rate capability suits legacy serial equipment, industrial control links, configuration ports, and service interfaces. Dedicated enable control can place the driver in a reduced-drive state when the associated receiver is not needed, while the integrated charge pump provides the RS-232 level translation required by the standard interface.
The ±15 kV ESD protection rating applies to the RS-232 serial-port connection pins and ground, adding valuable protection for equipment that may be connected to external cabling. ESD resilience is particularly important in industrial and communications equipment where a disconnected or partially installed cable can expose a port to electrostatic discharge. The 16-pin SSOP footprint also supports compact layouts without requiring a large connector-side interface package.
Typical uses include single-port RS-232 links in industrial controllers, test equipment, data acquisition systems, configuration and programming ports, and service interfaces for embedded products. The part is most appropriate where one bidirectional serial channel is needed, the data rate is below 250 kbps, and a 3.3 V or 5 V system supply is available. Designs requiring several RS-232 ports normally favor a multichannel transceiver instead.
A key implementation consideration is to place charge-pump capacitors, supply bypassing, and the RS-232 connector interface components exactly as shown in the manufacturer’s recommended layout. Keep connector-side traces short, provide a low-impedance ground return, and avoid routing sensitive signals alongside RS-232 outputs. These practices reduce radiated emissions, susceptibility to cable-borne noise, and ESD-related stress concentration.
This page combines the key MAX3221IDBE4 operating specifications, verified package information, drop-in replacement guidance, application-focused design guidance, and a parameter comparison for faster engineering selection. It is intended to help engineers determine whether the single-channel architecture, 250 kbps limit, SSOP footprint, and integrated ESD protection fit a particular RS-232 interface.
Pilihan pengganti yang segera untuk MAX3221IDBE4 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MAX3221IDBE4 (sama faktor bentuk dan kaki) — berbeza dalam Charge-Pump Architecture, ESD Protection, Product Type.
MAX3221IDBR
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MAX3221EAE+T
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →SN75C3221DBE4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ICL3221CVZ-T
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ICL3221EIAZ-T
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ICL3221EIAZ
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MAX3221IDBE4 Spesifikasi
| Product Type | Single-channel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| ESD Protection | ±15 kV |
| Gambaran Suhu Operasi | -40°C to +85°C |
| Kemasan | 16-pin SSOP |
| Jenis Pemasangan | Surface mount |
| Charge-Pump Architecture | Dual charge pump |
| Driver Enable | Dedicated enable pin |
| Interface Standard | RS-232 |
| ESD Protected Pins | Serial-port connection pins, including ground |
Panduan Konfigurasi Pin MAX3221IDBE4 16-pin ssop
Konfigurasi pin untuk MAX3221IDBE4 (16-pin ssop pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk MAX3221IDBE4.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
MAX3221IDBE4 patut untuk 6 aplikasis: Industrial Controller Configuration Port, Test and Measurement Equipment, Data Acquisition System, Embedded Equipment Service Interface, Point-of-Sale and Peripheral Interface, Security and Access-Control Equipment.
Industrial Controller Configuration Port
The MAX3221IDBE4 is appropriate for a controller that exposes one RS-232 configuration or maintenance port. Its 3 V to 5.5 V supply range allows operation beside either 3.3 V or 5 V logic, while the single driver and receiver provide one bidirectional serial channel. The 250 kbps maximum rate is more than sufficient for parameter uploads, diagnostic commands, and service traffic. The ±15 kV ESD protection on the serial connection pins strengthens the interface against charged cable contact. Place the input and output capacitors close to the device and route the connector ground directly to the interface ground to maintain signal integrity and improve electrostatic-discharge return paths.
Disebarkan
Test and Measurement Equipment
The MAX3221IDBE4 can provide a legacy serial control connection on test and measurement instruments that still use RS-232. One channel is adequate for remote commands, calibration results, or instrument-status reporting, and the 250 kbps limit supports the slow serial links commonly found in older laboratory equipment. Its integrated dual charge pump reduces the discrete capacitor burden associated with producing RS-232 levels from a 3.3 V or 5 V supply. The ±15 kV ESD protection is useful when users connect and disconnect external test leads. Maintain a short return path to the connector ground and separate the interface from sensitive measurement traces to limit coupling.
Disebarkan
Data Acquisition System
The MAX3221IDBE4 is suitable for commissioning and service communication in a compact data-acquisition system. The transceiver provides one receiver for incoming commands and one driver for responses or collected data, making it appropriate where telemetry is exchanged sequentially rather than through multiple simultaneous ports. Its 250 kbps rate supports many configuration and diagnostic protocols, while the 3 V to 5.5 V supply range permits direct use in mixed-voltage embedded systems. ESD protection of ±15 kV on the connection pins adds resilience for field-installed equipment. Use a continuous ground reference between the board and connector, and place supply and charge-pump capacitors according to the recommended layout.
Disebarkan
Embedded Equipment Service Interface
The MAX3221IDBE4 provides a compact service port for embedded systems that need one RS-232 channel for firmware loading, diagnostics, or configuration. A single-channel arrangement avoids the board area and power burden of a multichannel transceiver when only one service connector is required. The part operates from 3 V to 5.5 V and accepts data rates up to 250 kbps, covering common legacy boot and service protocols. Its integrated dual charge pump generates the required signal levels without a separate DC inverter, while ±15 kV ESD protection improves robustness at a user-accessible connector. Keep the port on a protected ground region and follow the exact capacitor values and enable configuration shown in the manufacturer documentation.
Disebarkan
Point-of-Sale and Peripheral Interface
The MAX3221IDBE4 can support a legacy point-of-sale peripheral or service terminal that communicates through one RS-232 port. The 250 kbps data rate is suitable for receipt printers, scanners, scales, and configuration tools using traditional serial protocols, while the 3 V to 5.5 V supply range integrates easily with modern embedded controllers. A dedicated enable function allows the transmitter to be managed when the port is not active, helping avoid unnecessary signal activity. The ±15 kV ESD rating protects the connection pins in retail equipment where cables are handled frequently. Route the interface away from display and switching-power noise, and preserve a low-impedance chassis-to-board ground path.
Disebarkan
Security and Access-Control Equipment
The MAX3221IDBE4 is useful for access-control terminals and security equipment that retain an RS-232 port for diagnostics, credential readers, or configuration. One bidirectional channel is sufficient for command-and-response protocols operating below 250 kbps. The device’s ±15 kV ESD protection is especially valuable around door controllers and other installations where connected cables may receive electrostatic discharge. Its 3 V to 5.5 V operating range supports both legacy 5 V interfaces and modern 3.3 V controller platforms. Use the enable input to control the driver during inactive periods, verify the logic polarity in the design, and keep the connector ground bonded near the interface entry point to reduce common-mode noise.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MAX3221IDBE4 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MAX3221IDBR | MAX3221EAE+T | SN75C3221DBE4 | ICL3221CVZ-T | ICL3221EIAZ-T |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Microchip Technology | Microchip Technology |
| Package | SSOP-16 | SSOP-16 | SSOP-16 | SSOP-16 | SSOP-16 | SSOP-16 |
Penyeberangsung Jelas
- Directly reusable MAX3221 interface implementation (vsMAX3221IDBR)
- Integrated protection for connector-side pins (vsMAX3221EAE+T)
- Single-channel footprint reduces board area (vsICL3221CVZ-T)
Catatan Desain
Place the MAX3221IDBE4 close to the RS-232 connector and follow the manufacturer’s reference layout for input, output, and charge-pump capacitors. Keep the connector ground and IC ground connected through a low-impedance path, and route differential RS-232 traces as a short pair. Excessively long or widely separated conductor traces can increase radiated emissions and make the interface more susceptible to externally coupled noise.
Do not treat the MAX3221IDBE4 as a general-purpose logic-level UART transceiver. The driver output must connect to an RS-232 receiver, and the receiver input must be exposed to RS-232 bipolar levels rather than TTL signals. Also confirm the enable polarity and distinguish shutdown from driver enable. Incorrect logic interpretation or an inappropriate cable connection can prevent reliable communication even when the supply voltage and decoupling are correct.
RS-232 driver outputs are high-voltage, fast-edge signals capable of coupling into nearby circuitry. Keep the connector-side section physically separated from analog, clock, and sensitive digital traces, and avoid placing it directly beneath high-speed switching nodes. A solid ground plane, short return path, and correctly positioned charge-pump capacitors reduce common-mode displacement and radiated coupling around the interface.
Maklumat Kesediaan
The manufacturer product information identifies the MAX3221 family and its RS-232 interface characteristics. RoHS, REACH, lead-free, halogen-free, and conflict-mineral declarations are not stated in the cited material and therefore remain unconfirmed.