Texas Instruments

MAX3232CDBE4 - 250kbps Dual RS-232 Transceiver | TI

MPN: MAX3232CDBE4 ✓ Aktif
3 V to 5.5 V Vdss 16-SSOP Package
MOQ: 1 |

MAX3232CDBE4 Ringkasan

Texas Instruments MAX3232CDBE4 is a dual-channel RS-232 line transceiver with two drivers, two receivers, a 3 V to 5.5 V supply range, and data rates up to 250 kbit/s in a 16-pin SSOP package. It also provides ±15 kV electrostatic-discharge protection on the serial-port connection pins, allowing it to serve as the physical interface between a modern digital system and an RS-232 port.

An RS-232 transceiver is an interface IC that converts low-voltage digital logic levels into RS-232-compatible signal levels and converts received RS-232 signals back into logic-compatible levels. Within the broader semiconductor hierarchy, this device belongs to the interface IC class, connecting UART controllers and microcontrollers to the drivers, receivers, connectors, and cabling used by point-to-point serial equipment.

The principal features include two drivers and two receivers, operation from a 3 V to 5.5 V VCC supply, and throughput up to 250 kbit/s. The device meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28, while its ±15 kV human-body-model ESD protection strengthens the bus-terminal connection against electrostatic discharge. The operating-voltage range permits use with both 3.3 V and 5 V system logic environments.

Internally, the MAX3232 combines its dual driver and receiver circuitry with a dual charge-pump circuit that develops the positive and negative voltage levels required by RS-232. This architecture supports a practical interface between TTL or CMOS-compatible UART logic and an RS-232 port without requiring a separate external charge-pump supply. The integrated protection is specified for the serial-port connection pins, including ground, where applicable.

Typical uses include industrial serial adapters, point-of-sale equipment, data-acquisition systems, embedded control consoles, and legacy peripheral connectivity. Its 250 kbit/s capability accommodates many RS-232 control, configuration, and instrument-control links while remaining compatible with the electrical requirements of the RS-232 standard.

The most important layout consideration is the placement of the charge-pump capacitors and the protection-network connections. Keep the required external capacitors close to their specified pins, provide a low-impedance ground return, and route the RS-232 connector-side nets away from sensitive logic. Validate the complete board for ESD return current because connector protection alone does not eliminate the need for sound enclosure and ground design.

This page combines the manufacturer interface information with package-specific selection guidance, verified drop-in alternatives, and practical PCB-design guidance. It is intended to help engineers confirm electrical fit, package compatibility, protection requirements, and implementation details before incorporating the MAX3232 into a new RS-232 design.

Pilihan pengganti yang segera untuk MAX3232CDBE4 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera MAX3232CDBE4 (sama faktor bentuk dan kaki) — berbeza dalam ESD Protection, Supply Voltage Range.

Analog Devices
ESD Protection: ±15 kV
Supply Voltage Range: 3.0 V to 5.5 V
Bandingkan Dengan MAX3232CDBE4 →

MAX3232EEAE+

✅ Masuk Drop-In
Analog Devices
📦 16-SSOP
True RS-232 transceiver · 2 · 2 · 3.0 V to 5.5 V · 1 Mbps · ±15 kV · Down to 10 nA · 2

Hubungi untuk harga

Lihat Datasheet →

MAX3232CDBE4 Spesifikasi

Transceiver Configuration 2 drivers and 2 receivers
RS-232 Data Rate 250 kbit/s
Supply Voltage Range 3 V to 5.5 V
Protocol RS-232
ESD Protection ±15 kV using the human-body model
RS-232 Compliance Meets or exceeds TIA/EIA-232-F requirements
ITU Standard Compliance Meets or exceeds ITU V.28 requirements
Number of Drivers 2
Number of Receivers 2
Kemasan 16-SSOP
Package Body Width 5.30 mm
Package Lead Width 0.209 mm
Jenis Pemasangan Surface mount
Packaging Tube

Panduan Konfigurasi Pin MAX3232CDBE4 0.209 mm

Konfigurasi pin untuk MAX3232CDBE4 (0.209 mm pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 0.209 mm untuk MAX3232CDBE4

Tiada data garisan pin yang diperoleh untuk MAX3232CDBE4.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

MAX3232CDBE4 patut untuk 6 aplikasis: Industrial RS-232 Control Interface, Point-of-Sale Terminal Connectivity, Data-Acquisition Instrument Link, Embedded Serial Console, Legacy Peripheral Adapter, Service and Diagnostic Equipment.

🏭

Industrial RS-232 Control Interface

The MAX3232CDBE4 suits industrial control equipment that must bridge a 3.3 V or 5 V UART to an RS-232 service port. Its two drivers and two receivers provide two bidirectional RS-232 channels, while operation up to 250 kbit/s supports configuration, status, and supervisory traffic. The 3 V to 5.5 V supply range permits use with both 3.3 V and 5 V embedded controllers. Place the charge-pump capacitors close to the IC, connect a continuous ground return, and keep connector-side routing away from sensitive logic. The ±15 kV human-body-model ESD rating adds protection at the exposed bus interface, although the enclosure and chassis ground must also be designed for electrostatic-discharge events.

🖥️

Point-of-Sale Terminal Connectivity

The MAX3232CDBE4 can provide legacy RS-232 connectivity for point-of-sale terminals, receipt printers, scales, or service tools using a TTL/CMOS UART. Two driver and two receiver channels permit two physical RS-232 links without adding another transceiver IC. The 250 kbit/s operating capability is suitable for routine transaction and configuration traffic, although actual throughput also depends on the UART, cable, and protocol. Its 3 V minimum supply allows deployment in modern 3.3 V embedded systems, reducing the need for a separate 5 V interface rail. Use the manufacturer application circuit for charge-pump capacitance and provide a low-impedance ground path from the transceiver to the connector shield or chassis structure.

📡

Data-Acquisition Instrument Link

The MAX3232CDBE4 is appropriate for connecting a data-acquisition instrument or laboratory controller through an RS-232 port. The two-channel arrangement can handle separate transmit and receive paths or support two instrument connections, while the 250 kbit/s limit accommodates many command and measurement-data protocols. The 3 V to 5.5 V operating range lets the interface coexist with 3.3 V control logic while meeting TIA/EIA-232-F and ITU V.28 interface requirements. For reliable measurements, keep switching or charge-pump loop areas compact and route the interface return alongside each cable shield. The integrated ±15 kV HBM protection improves robustness, but long unshielded cable runs still require correct grounding and connector selection.

🔧

Embedded Serial Console

The MAX3232CDBE4 can add an RS-232 diagnostic console to an embedded controller or programmable logic system. The two receivers provide receive channels for console or status data, and the two drivers support outbound command or control traffic. Running from 3 V to 5.5 V allows use across common embedded supply systems, while the 16-SSOP package saves board area compared with larger transceivers. Place the charge-pump capacitors at the pins identified in the datasheet and connect the RS-232 ground return to the board ground without introducing long narrow traces. The ±15 kV HBM protection is valuable for service ports exposed to user-accessible cables, but engineers should still evaluate enclosure grounding, surge paths, and system-level isolation.

🔌

Legacy Peripheral Adapter

The MAX3232CDBE4 is useful in adapters that connect a modern USB-capable processor or microcontroller to an established RS-232 peripheral. Its 2/2 transceiver arrangement allows full-duplex communication on one interface and supports a second channel when the peripheral exposes additional RS-232 lines. The 3 V to 5.5 V supply range simplifies adaptation to 3.3 V and 5 V systems, and the 250 kbit/s rate covers many legacy control protocols. Preserve the RS-232 ground connection and use a continuous reference path between the adapter and connected equipment. Follow the manufacturer's capacitor and decoupling guidance, and avoid placing the connector-side network next to precision analog or high-speed digital traces.

⚡

Service and Diagnostic Equipment

The MAX3232CDBE4 can serve as the RS-232 interface in service equipment, diagnostic fixtures, and programmable test systems. Its two-driver and two-receiver architecture supports command transmission and response reception, with up to 250 kbit/s available for typical instrument-control traffic. The wide 3 V to 5.5 V supply range accommodates both legacy 5 V logic and newer 3.3 V platforms. Use a low-impedance ground plane, short charge-pump capacitor connections, and a deliberate separation between logic-side and connector-side routing to limit coupling. The ±15 kV HBM ESD rating helps protect exposed interfaces, but proper cable strain relief, shield termination, and equipment grounding are required for dependable field operation.

What is the operating voltage of MAX3232CDBE4?
The MAX3232CDBE4 operates from a 3 V to 5.5 V VCC supply. According to the Texas Instruments MAX3232 product page and manufacturer datasheet, this range supports both 3.3 V and 5 V digital systems while operating at up to 250 kbit/s. Keep the input supply within the stated limits and use the application circuit's recommended charge-pump capacitor values to maintain correct voltage generation and RS-232 output levels.
What are the key specifications of MAX3232CDBE4 that engineers should know?
The MAX3232CDBE4 is a 2-driver, 2-receiver RS-232 transceiver operating from 3 V to 5.5 V at up to 250 kbit/s. It provides ±15 kV human-body-model ESD protection on the serial-port connection pins and meets or exceeds TIA/EIA-232-F and ITU V.28 requirements. Texas Instruments specifies the device in a 16-SSOP package with tube packaging for the MAX3232CDBE4 order code.
Where to download MAX3232CDBE4 datasheet PDF?
The official MAX3232CDBE4 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/max3232.pdf. The document describes the dual charge-pump architecture, electrical characteristics, pin functions, typical circuits, and RS-232 applications. Use the manufacturer's pin-description table and application circuit before assigning PCB tracks or selecting the external charge-pump capacitors.
Where can I find the MAX3232CDBE4 pinout?
The MAX3232CDBE4 pinout is published in the pin-configuration section of the Texas Instruments MAX3232 manufacturer datasheet. The exact ordering code uses a 16-SSOP package, so the 16-pin footprint and pin-1 orientation must be checked against the package drawing before layout release. Do not infer individual pin functions from a generic RS-232 transceiver because charge-pump capacitor connections vary between devices.
Does MAX3232CDBE4 support ±15 kV ESD protection?
Yes. The MAX3232CDBE4 provides ±15 kV ESD protection using the human-body model on the RS-232 bus-terminal pins. According to the Texas Instruments manufacturer datasheet, the protected connections include the serial-port pins and ground. This rating protects the interface IC during electrostatic discharge events, although correct chassis grounding, enclosure design, and board-level return paths remain necessary.
What is the maximum data rate of MAX3232CDBE4?
The MAX3232CDBE4 operates at RS-232 data rates up to 250 kbit/s. This supports UART links commonly used for configuration, monitoring, and control traffic in industrial and instrumentation systems. The rate is a device-level capability; the installed cable, connector, UART settings, load, signal integrity, and software protocol must also support the intended throughput.
Is MAX3232CDBE4 compatible with 3.3 V UART logic?
Yes. The MAX3232CDBE4 operates from a 3 V to 5.5 V supply, which supports 3.3 V UART logic systems. Its two receivers convert incoming RS-232 signals to compatible logic levels, while its two drivers convert outgoing logic signals to RS-232 levels. Confirm signal-level thresholds and supply sequencing against the manufacturer datasheet for the specific UART and connector arrangement.
Where to buy MAX3232CDBE4 online?
Use the Request a Quote form on this page to request MAX3232CDBE4 availability, packaging, and current lead time from XAIPART. The part is a 16-SSOP RS-232 transceiver identified by the MAX3232CDBE4 ordering code. For design review, confirm the 16-SSOP footprint, supply requirements, charge-pump capacitors, and the tube packaging shown in the manufacturer ordering information.
What is the price of MAX3232CDBE4?
Current MAX3232CDBE4 pricing is generated through the XAIPART Request a Quote form on this page. The structured pricing interface reflects current channel and quantity information without embedding a potentially stale price in engineering guidance. Submit the required quantity, package, and destination information to obtain the applicable quote and availability confirmation.
What is the lead time for MAX3232CDBE4?
Submit a MAX3232CDBE4 request through the Request a Quote form on this page to confirm the current lead time and available quantity. Lead time can vary with the ordering code, tube packaging, order quantity, and current supply conditions. Use the returned confirmation for production planning, and avoid assuming that a similar MAX3232 variant has the same scheduling status.
Is MAX3232CDBE4 in stock?
Current MAX3232CDBE4 stock status should be confirmed through the Request a Quote form on this page. The manufacturer product information identifies the MAX3232 family, but live inventory and allocation are commercial data that change independently of the device specifications. Request the exact MPN, quantity, and packaging required by your production plan.
What can replace MAX3232CDBE4?
MAX3232EEAE+ is the closest identified drop-in replacement because it uses the same 16-SSOP class of package and provides the same 2-driver, 2-receiver RS-232 function with 3 V to 5.5 V operation, 250 kbit/s capability, and ±15 kV human-body-model protection. Review pin assignments, capacitor connections, ordering information, and lifecycle status before approving any substitution for production.
Is MAX3232EEAE+ the same as MAX3232CDBE4?
MAX3232EEAE+ is functionally equivalent to MAX3232CDBE4 in the principal published specifications: two drivers, two receivers, 3 V to 5.5 V supply operation, 250 kbit/s data rate, and ±15 kV human-body-model ESD protection. Both use a 16-SSOP package. Because the ordering suffix can encode operating-temperature and qualification differences, verify the complete ordering table and pin functions before treating them as interchangeable.
When should I choose MAX3232CDBE4 over MAX3232EEAE+?
Choose MAX3232CDBE4 when the completed manufacturer ordering information for that suffix best matches your required temperature range, qualification, and production conditions. Choose MAX3232EEAE+ when its ordering information satisfies the same requirements and procurement needs while retaining the same principal electrical ratings and 16-SSOP footprint. In both cases, verify the pin table and charge-pump capacitor values before PCB release.
What is the best MAX3232 equivalent for MAX3232CDBE4?
MAX3232EEAE+ is the best identified equivalent in this comparison because it preserves the 16-SSOP package, two-driver and two-receiver configuration, 3 V to 5.5 V supply range, 250 kbit/s rate, and ±15 kV human-body-model ESD rating. No additional cross-brand pin-compatible alternative was established by the available records, so an unverified competitor part should not be treated as a drop-in replacement without footprint and pinout validation.
Does MAX3232CDBE4 meet RS-232 standards?
Yes. According to the Texas Instruments manufacturer datasheet, the MAX3232 meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28. Its bus-terminal circuitry includes ±15 kV human-body-model ESD protection. Compliance covers the stated interface requirements, but a compliant transceiver does not guarantee signal integrity over arbitrary cable lengths or poorly implemented connectors.
How should MAX3232CDBE4 charge-pump capacitors be placed?
Place the charge-pump capacitors directly between their specified IC pins with the shortest possible traces and a ground-plane return. Follow the manufacturer datasheet for capacitor value, tolerance, voltage rating, and topology. Extra trace length can increase charge-pump loop area and degrade output behavior, while poor grounding can route transient current into sensitive logic. Verify the final arrangement with the reference application circuit.

Data referensi kejuruteraan untuk MAX3232CDBE4 — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose MAX3232CDBE4 when the ordering suffix, temperature range, qualification requirements, and procurement plan align with your exact manufacturer ordering information. Its two drivers, two receivers, 3 V to 5.5 V supply range, 250 kbit/s rate, and ±15 kV HBM protection are well suited to industrial controllers, service equipment, legacy adapters, and data-acquisition links. MAX3232EEAE+ is the closest identified drop-in option because it shares the 16-SSOP package and principal published ratings. Select it when its complete ordering and lifecycle information offers a better sourcing fit, but verify pin functions and temperature requirements before substitution. No additional cross-brand drop-in candidate was established from the available cross-reference records, so do not approve a competitor solely from matching the RS-232 function. For any chosen device, follow the manufacturer application circuit for charge-pump capacitors, connector-side grounding, and ESD return-current control.

Perbandingan dengan Gantian

Parametr Produk Ini MAX3232EEAE+
Package 16-SSOP 16-SSOP
Brand Texas Instruments Texas Instruments
Driver and Receiver Count 2 drivers and 2 receivers 2 drivers and 2 receivers
Supply Voltage Range 3 V to 5.5 V 3 V to 5.5 V
Maximum Data Rate 250 kbit/s 250 kbit/s
ESD Protection ±15 kV HBM ±15 kV HBM
RS-232 Standard Compliance TIA/EIA-232-F and ITU V.28 TIA/EIA-232-F and ITU V.28
Interface Type RS-232 transceiver RS-232 transceiver

Penyeberangsung Jelas

  • Published electrical performance matches the identified drop-in option (vsMAX3232EEAE+)
  • Dual-channel interface reduces the number of separate RS-232 transceivers (vsMAX3232EEAE+)
  • Wide supply compatibility supports both 3.3 V and 5 V systems (vsMAX3232EEAE+)

Catatan Desain

Place the charge-pump capacitors directly across the pins and terminals shown in the manufacturer application circuit. Keep these loops short, use a continuous ground-plane reference, and avoid routing connector-side nets beneath the transceiver or adjacent sensitive analog sections. The published 16-SSOP package leaves little space for long capacitor leads, so prioritize a compact placement over a visually symmetrical layout.

Separate UART logic-side nets from RS-232 connector-side nets as far as practical. Keep the signal-ground return continuous and provide a deliberate chassis or shield connection according to the connector and enclosure strategy. This reduces susceptibility to ESD and ground-potential differences while preserving the common reference needed by the receiver. Validate the board with an oscilloscope to confirm that switching activity on adjacent circuits does not corrupt the RS-232 waveform.

Do not assume that a 16-SSOP transceiver can be substituted solely because its nominal pin count matches. Before replacing MAX3232CDBE4, compare the complete pin-description table, charge-pump capacitor connections, operating-temperature suffix, and lifecycle status. Also verify that the intended UART logic levels and cable-side connector pinout agree; a package match alone does not establish functional drop-in compatibility.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The manufacturer information identifies TIA/EIA-232-F and ITU V.28 interface compliance and ±15 kV HBM ESD protection. Separate RoHS, REACH, AEC-Q100, halogen-free, and conflict-minerals confirmations were not established.

Pencarian Berhubungan

MAX3232CDBE4 datasheet MAX3232CDBE4 pinout MAX3232CDBE4 datasheet pdf MAX3232CDBE4 equivalent MAX3232CDBE4 replacement MAX3232CDBE4 cross reference MAX3232CDBE4 vs MAX3232EEAE+ MAX3232CDBE4 footprint MAX3232CDBE4 application circuit MAX3232CDBE4 price MAX3232CDBE4 stock Texas Instruments MAX3232CDBE4 MAX3232 16-SSOP RS-232 MAX3232CDBE4 industrial serial adapter MAX3232CDBE4 250 kbit/s

Komponen dan Tanda berkaitan

Texas Instruments MAX3232CDBE4 MAX3232EEAE+ MAX3232CDE4 MAX3232 RS-232 transceiver line driver line receiver interface IC semiconductor UART charge-pump circuit TIA/EIA-232-F ITU V.28 ESD protection human-body model HBM 16-SSOP SSOP package family surface-mount package SMD 3.3 V logic 5 V logic 250 kbit/s industrial serial interface
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ