MAX3232CDBE4 - 250kbps Dual RS-232 Transceiver | TI
MPN: MAX3232CDBE4 ✓ Hoạt độngMAX3232CDBE4 Tóm tắt
An RS-232 transceiver is an interface IC that converts low-voltage digital logic levels into RS-232-compatible signal levels and converts received RS-232 signals back into logic-compatible levels. Within the broader semiconductor hierarchy, this device belongs to the interface IC class, connecting UART controllers and microcontrollers to the drivers, receivers, connectors, and cabling used by point-to-point serial equipment.
The principal features include two drivers and two receivers, operation from a 3 V to 5.5 V VCC supply, and throughput up to 250 kbit/s. The device meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28, while its ±15 kV human-body-model ESD protection strengthens the bus-terminal connection against electrostatic discharge. The operating-voltage range permits use with both 3.3 V and 5 V system logic environments.
Internally, the MAX3232 combines its dual driver and receiver circuitry with a dual charge-pump circuit that develops the positive and negative voltage levels required by RS-232. This architecture supports a practical interface between TTL or CMOS-compatible UART logic and an RS-232 port without requiring a separate external charge-pump supply. The integrated protection is specified for the serial-port connection pins, including ground, where applicable.
Typical uses include industrial serial adapters, point-of-sale equipment, data-acquisition systems, embedded control consoles, and legacy peripheral connectivity. Its 250 kbit/s capability accommodates many RS-232 control, configuration, and instrument-control links while remaining compatible with the electrical requirements of the RS-232 standard.
The most important layout consideration is the placement of the charge-pump capacitors and the protection-network connections. Keep the required external capacitors close to their specified pins, provide a low-impedance ground return, and route the RS-232 connector-side nets away from sensitive logic. Validate the complete board for ESD return current because connector protection alone does not eliminate the need for sound enclosure and ground design.
This page combines the manufacturer interface information with package-specific selection guidance, verified drop-in alternatives, and practical PCB-design guidance. It is intended to help engineers confirm electrical fit, package compatibility, protection requirements, and implementation details before incorporating the MAX3232 into a new RS-232 design.
Bộ thay thế dễ dàng lắp đặt cho MAX3232CDBE4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX3232CDBE4 (cùng hình factor và footprint) — khác nhau ở ESD Protection, Supply Voltage Range.
MAX3232EEAE+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232CDBE4 Thông số kỹ thuật
| Transceiver Configuration | 2 drivers and 2 receivers |
| RS-232 Data Rate | 250 kbit/s |
| Supply Voltage Range | 3 V to 5.5 V |
| Protocol | RS-232 |
| ESD Protection | ±15 kV using the human-body model |
| RS-232 Compliance | Meets or exceeds TIA/EIA-232-F requirements |
| ITU Standard Compliance | Meets or exceeds ITU V.28 requirements |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Hộp | 16-SSOP |
| Package Body Width | 5.30 mm |
| Package Lead Width | 0.209 mm |
| Kiểu lắp đặt | Surface mount |
| Packaging | Tube |
Hướng dẫn cấu hình chân MAX3232CDBE4 0.209 mm
Cấu hình chân cho MAX3232CDBE4 (0.209 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3232CDBE4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3232CDBE4 phù hợp cho 6 Áp dụngs: Industrial RS-232 Control Interface, Point-of-Sale Terminal Connectivity, Data-Acquisition Instrument Link, Embedded Serial Console, Legacy Peripheral Adapter, Service and Diagnostic Equipment.
Industrial RS-232 Control Interface
The MAX3232CDBE4 suits industrial control equipment that must bridge a 3.3 V or 5 V UART to an RS-232 service port. Its two drivers and two receivers provide two bidirectional RS-232 channels, while operation up to 250 kbit/s supports configuration, status, and supervisory traffic. The 3 V to 5.5 V supply range permits use with both 3.3 V and 5 V embedded controllers. Place the charge-pump capacitors close to the IC, connect a continuous ground return, and keep connector-side routing away from sensitive logic. The ±15 kV human-body-model ESD rating adds protection at the exposed bus interface, although the enclosure and chassis ground must also be designed for electrostatic-discharge events.
Được đề xuất
Point-of-Sale Terminal Connectivity
The MAX3232CDBE4 can provide legacy RS-232 connectivity for point-of-sale terminals, receipt printers, scales, or service tools using a TTL/CMOS UART. Two driver and two receiver channels permit two physical RS-232 links without adding another transceiver IC. The 250 kbit/s operating capability is suitable for routine transaction and configuration traffic, although actual throughput also depends on the UART, cable, and protocol. Its 3 V minimum supply allows deployment in modern 3.3 V embedded systems, reducing the need for a separate 5 V interface rail. Use the manufacturer application circuit for charge-pump capacitance and provide a low-impedance ground path from the transceiver to the connector shield or chassis structure.
Được đề xuất
Data-Acquisition Instrument Link
The MAX3232CDBE4 is appropriate for connecting a data-acquisition instrument or laboratory controller through an RS-232 port. The two-channel arrangement can handle separate transmit and receive paths or support two instrument connections, while the 250 kbit/s limit accommodates many command and measurement-data protocols. The 3 V to 5.5 V operating range lets the interface coexist with 3.3 V control logic while meeting TIA/EIA-232-F and ITU V.28 interface requirements. For reliable measurements, keep switching or charge-pump loop areas compact and route the interface return alongside each cable shield. The integrated ±15 kV HBM protection improves robustness, but long unshielded cable runs still require correct grounding and connector selection.
Được đề xuất
Embedded Serial Console
The MAX3232CDBE4 can add an RS-232 diagnostic console to an embedded controller or programmable logic system. The two receivers provide receive channels for console or status data, and the two drivers support outbound command or control traffic. Running from 3 V to 5.5 V allows use across common embedded supply systems, while the 16-SSOP package saves board area compared with larger transceivers. Place the charge-pump capacitors at the pins identified in the datasheet and connect the RS-232 ground return to the board ground without introducing long narrow traces. The ±15 kV HBM protection is valuable for service ports exposed to user-accessible cables, but engineers should still evaluate enclosure grounding, surge paths, and system-level isolation.
Được đề xuất
Legacy Peripheral Adapter
The MAX3232CDBE4 is useful in adapters that connect a modern USB-capable processor or microcontroller to an established RS-232 peripheral. Its 2/2 transceiver arrangement allows full-duplex communication on one interface and supports a second channel when the peripheral exposes additional RS-232 lines. The 3 V to 5.5 V supply range simplifies adaptation to 3.3 V and 5 V systems, and the 250 kbit/s rate covers many legacy control protocols. Preserve the RS-232 ground connection and use a continuous reference path between the adapter and connected equipment. Follow the manufacturer's capacitor and decoupling guidance, and avoid placing the connector-side network next to precision analog or high-speed digital traces.
Được đề xuất
Service and Diagnostic Equipment
The MAX3232CDBE4 can serve as the RS-232 interface in service equipment, diagnostic fixtures, and programmable test systems. Its two-driver and two-receiver architecture supports command transmission and response reception, with up to 250 kbit/s available for typical instrument-control traffic. The wide 3 V to 5.5 V supply range accommodates both legacy 5 V logic and newer 3.3 V platforms. Use a low-impedance ground plane, short charge-pump capacitor connections, and a deliberate separation between logic-side and connector-side routing to limit coupling. The ±15 kV HBM ESD rating helps protect exposed interfaces, but proper cable strain relief, shield termination, and equipment grounding are required for dependable field operation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3232CDBE4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3232EEAE+ |
|---|---|---|
| Package | 16-SSOP | 16-SSOP |
| Brand | Texas Instruments | Texas Instruments |
| Driver and Receiver Count | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s | 250 kbit/s |
| ESD Protection | ±15 kV HBM | ±15 kV HBM |
| RS-232 Standard Compliance | TIA/EIA-232-F and ITU V.28 | TIA/EIA-232-F and ITU V.28 |
| Interface Type | RS-232 transceiver | RS-232 transceiver |
Bảo phân biệt quan trọng
- Published electrical performance matches the identified drop-in option (vsMAX3232EEAE+)
- Dual-channel interface reduces the number of separate RS-232 transceivers (vsMAX3232EEAE+)
- Wide supply compatibility supports both 3.3 V and 5 V systems (vsMAX3232EEAE+)
Ghi chú thiết kế
Place the charge-pump capacitors directly across the pins and terminals shown in the manufacturer application circuit. Keep these loops short, use a continuous ground-plane reference, and avoid routing connector-side nets beneath the transceiver or adjacent sensitive analog sections. The published 16-SSOP package leaves little space for long capacitor leads, so prioritize a compact placement over a visually symmetrical layout.
Separate UART logic-side nets from RS-232 connector-side nets as far as practical. Keep the signal-ground return continuous and provide a deliberate chassis or shield connection according to the connector and enclosure strategy. This reduces susceptibility to ESD and ground-potential differences while preserving the common reference needed by the receiver. Validate the board with an oscilloscope to confirm that switching activity on adjacent circuits does not corrupt the RS-232 waveform.
Do not assume that a 16-SSOP transceiver can be substituted solely because its nominal pin count matches. Before replacing MAX3232CDBE4, compare the complete pin-description table, charge-pump capacitor connections, operating-temperature suffix, and lifecycle status. Also verify that the intended UART logic levels and cable-side connector pinout agree; a package match alone does not establish functional drop-in compatibility.
Thông tin tuân thủ
The manufacturer information identifies TIA/EIA-232-F and ITU V.28 interface compliance and ±15 kV HBM ESD protection. Separate RoHS, REACH, AEC-Q100, halogen-free, and conflict-minerals confirmations were not established.