Texas Instruments

MAX3232CDWG4 - Dual RS-232 Transceiver | Texas Instruments

MPN: MAX3232CDWG4 ✓ Aktif
3 V to 5.5 V Vdss 16-pin SOIC Package
MOQ: 1 |

MAX3232CDWG4 Ringkasan

The Texas Instruments MAX3232CDWG4 is a dual RS-232 line driver and receiver transceiver rated for 3 V to 5.5 V supply operation, 250 kbit/s data rates, and ±15 kV human-body-model ESD protection. The device is packaged in a 16-pin SOIC with a commercial operating-temperature grade of 0°C to 70°C. Its two drivers and two receivers support point-to-point RS-232 links where logic-level equipment must connect to a larger ground-referenced serial interface.

An RS-232 transceiver is an interface IC that bridges the voltage-domain difference between CMOS or other digital logic and the bipolar signal levels used by RS-232 equipment. Within the interface hierarchy, the MAX3232CDWG4 is a multichannel line transceiver containing RS-232 line drivers, RS-232 receivers, and a dual charge-pump power supply. That internal hierarchy also explains why four external 0.1 µF capacitors are used to generate the required positive and negative RS-232 voltage levels.

The principal benefits are operation from a single 3 V to 5.5 V supply, two transmit channels, two receive channels, a maximum data rate of 250 kbit/s, and ±15 kV HBM ESD protection. The MAX3232 family meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28 as identified in the device documentation. These characteristics make the part suitable for industrial control, instrumentation, POS equipment, and embedded serial-port designs.

Technically, the charge-pump circuitry converts the single positive supply into the voltage swings required by RS-232 drivers. The receiver side detects differential bipolar inputs and translates them into CMOS-compatible logic levels. The MAX3232CDWG4 is a commercial-temperature option, while the MAX3232E family is identified by Texas Instruments as an improved direct replacement for MAX3232 in new designs. Circuit designers should nevertheless compare device-specific enable, fail-safe, and power-control behavior before approving a substitute.

Typical uses include connecting an embedded controller to a legacy printer, barcode reader, test instrument, or industrial peripheral over a full-duplex RS-232 link. The 16-pin SOIC package is also practical for designs that already use surface-mount assembly and can accommodate the external charge-pump capacitor network. Because the line interface is not a differential CAN or RS-485 bus, the interconnect should be implemented as a point-to-point RS-232 connection with the required signal-ground reference.

A key design consideration is capacitor placement. Position the four 0.1 µF charge-pump capacitors close to their associated device pins, with the shortest possible ground-return paths. Protect exposed connector-side pins against electrostatic discharge, provide a stable ground reference, and route the RS-232 cable away from sensitive analog and high-speed digital traces.

This product page consolidates the device specifications, verified sourcing links, drop-in comparison information, application guidance, and practical layout considerations into one engineering-focused reference. It helps distinguish electrical equivalents from mechanically similar parts and highlights the checks required before reusing an existing 16-pin SOIC layout.

Pilihan pengganti yang segera untuk MAX3232CDWG4 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

MAX3232EIDWR

✅ Masuk Drop-In
📦 SOIC-16
Manufacturer identifies MAX3232E as an improved direct replacement for MAX3232; channel count remains 2/2, a 0% difference, while device-specific fail-safe and enable behavior must be checked.

📋 Alternatif rujukan (tidak dalam katalog)

MAX3232IDW

✅ Masuk Drop-In
Texas Instruments
📦 SOIC-16
RS-232 line driver/receiver transceiver · 2 · 2 · 3 V to 5.5 V · 250 kbit/s · 300 µA typical · ±15 kV · 4 x 0.1 µF

Hubungi untuk harga

Lihat Datasheet →

MAX3232CDE4

✅ Masuk Drop-In
Texas Instruments
📦 SOIC-16
RS-232 line driver/receiver transceiver · 2/2 · Full duplex · 3 V to 5.5 V · 250 kbps · ±15 kV HBM · 0 °C to 70 °C · 16-SOIC, 0.154 in (3.90 mm) width

Hubungi untuk harga

Lihat Datasheet →

SN65C3232D

✅ Masuk Drop-In
📦 SOIC-16
Provides the same 2/2 driver-receiver configuration and ±15 kV ESD protection, a 0% documented difference in those parameters, with equivalent 16-pin RS-232 connectivity described as pin-to-pin compatible.

📋 Alternatif rujukan (tidak dalam katalog)

MAX3232CDWG4 Spesifikasi

Device Type 2/2 RS-232 line transceiver
Number of Drivers 2
Number of Receivers 2
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 250 kbit/s
ESD Protection ±15 kV HBM
External Charge-Pump Capacitors 4 × 0.1 µF
RS-232 Compliance TIA/EIA-232-F and ITU V.28
Logic Technology CMOS
Gambaran Suhu Operasi 0°C to 70°C
Kemasan 16-pin SOIC
Package Width 7.50 mm
Package Body Length 0.295 inch
Gaya Pemasangan Surface mount
Temperature Grade Commercial
Lead-Free Status Lead free

Panduan Konfigurasi Pin MAX3232CDWG4 0.295 inch

Konfigurasi pin untuk MAX3232CDWG4 (0.295 inch pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 0.295 inch untuk MAX3232CDWG4

Tiada data garisan pin yang diperoleh untuk MAX3232CDWG4.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

MAX3232CDWG4 patut untuk 6 aplikasis: Embedded Controller Serial Interface, Industrial Serial Instrument, Point-of-Sale Terminal Interface, Printer and Barcode Reader Connectivity, RS-232-to-Logic Bridge, Communication and Network Appliance.

🔧

Embedded Controller Serial Interface

The MAX3232CDWG4 suits an embedded controller that must communicate with a legacy peripheral over a point-to-point RS-232 link. Its 3 V to 5.5 V supply range allows operation from common 3.3 V or 5 V logic rails, while the 2/2 arrangement supports two transmit and two receive functions. A 250 kbit/s maximum rate accommodates conventional serial-console, configuration, and service protocols. The circuit should use one driver and one receiver for full-duplex communication, with the RS-232 ground connected to the equipment signal ground. Four 0.1 µF charge-pump capacitors remain mandatory, and their placement should be treated as part of the high-frequency layout rather than as optional decoupling.

🏭

Industrial Serial Instrument

MAX3232CDWG4 can provide the electrical interface between a controller and an RS-232 test or measurement instrument. The commercial 0°C to 70°C rating is appropriate for controlled indoor equipment, and ±15 kV HBM protection adds a useful robustness margin on the logic and connector-related pins. At a maximum 250 kbit/s, the link can support instrument command and response traffic without relying on long-distance high-speed guarantees. Use a point-to-point cable arrangement, connect signal ground, and keep the transceiver’s charge-pump nodes away from sensitive analog inputs. Connector-side protection and enclosure grounding remain part of the overall surge and ESD design.

🖥️

Point-of-Sale Terminal Interface

The MAX3232CDWG4 is suitable for point-of-sale equipment that connects a controller board to a printer, customer display, scanner, or other legacy RS-232 peripheral. Its two drivers and two receivers allow multiple unidirectional links or a full-duplex primary port, while its single 3 V to 5.5 V supply simplifies integration with embedded systems operating at either 3.3 V or 5 V. The 250 kbit/s capability is more than adequate for many peripheral-control protocols. Keep external cables away from processor clocks and switching supplies, use the device ground as the signal reference, and place the four required 0.1 µF capacitors directly beside the charge-pump pins to minimize switching transients.

📱

Printer and Barcode Reader Connectivity

A pair of MAX3232CDWG4 channels can connect a control board to a receipt printer and a barcode reader without using separate single-driver and single-receiver devices. The interface operates from a 3 V to 5.5 V supply and provides two drivers and two receivers at up to 250 kbit/s, which supports common printer and scanner command formats. Because RS-232 uses bipolar signaling and a ground reference, verify cable pin assignments and logic polarity at the connector rather than assuming that TX and RX names always match. Provide adequate separation from motors and relay coils, and route the four charge-pump capacitors close to the transceiver to prevent radiated disturbance from the switched capacitor supply.

🌐

RS-232-to-Logic Bridge

MAX3232CDWG4 can bridge CMOS-level controller signals and the bipolar RS-232 interface used by older equipment. The receiver translates RS-232 levels into logic-compatible signals, while the driver produces the required positive and negative swing from the 3 V to 5.5 V system supply. Its 2/2 configuration permits either one bidirectional link with spare channels or two point-to-point links. The ±15 kV HBM protection rating should be considered when selecting connectors and enclosure grounding, but it does not replace cable surge protection. Confirm the receiver’s logic state during power transitions and verify that the host software uses the same baud rate and signal polarity.

📺

Communication and Network Appliance

MAX3232CDWG4 is useful in communication equipment that retains a service, configuration, or management connector implemented with RS-232. The 16-pin SOIC package simplifies surface-mount assembly, and the 2/2 arrangement can manage more than one serial function without duplicating the charge-pump circuitry. A 250 kbit/s maximum rate supports management and firmware-transfer traffic. In a network appliance, isolate the RS-232 connector from chassis and logic ground according to the system’s grounding policy, and protect the cable entry against electrostatic discharge. Keep the charge-pump capacitor loop compact and ensure the 0°C to 70°C commercial operating range is maintained inside the enclosure.

Ringkasan Produk Disebarkan

MAX3232EIDWR Manufacturer-recommended improved MAX3232-family alternative Dipergunakan di: Embedded Controller Serial Interface, Point-of-Sale Terminal Interface, RS-232-to-Logic Bridge, Communication and Network Appliance SN65C3232D Pin-compatible 2/2 RS-232 transceiver candidate Dipergunakan di: Embedded Controller Serial Interface, Printer and Barcode Reader Connectivity, Communication and Network Appliance MAX3232IDW Texas Instruments Dipergunakan di: Industrial Serial Instrument, Point-of-Sale Terminal Interface, RS-232-to-Logic Bridge MAX3232CDE4 Texas Instruments Dipergunakan di: Industrial Serial Instrument, Printer and Barcode Reader Connectivity
What is the operating voltage of MAX3232CDWG4?
The MAX3232CDWG4 operates from a 3 V to 5.5 V single supply. According to the Texas Instruments device documentation, this range permits the same RS-232 interface circuit to be used with 3.3 V and 5 V systems. The internal charge pump generates the positive and negative voltages required by the RS-232 drivers, so the external system supply does not need to provide bipolar RS-232 voltages.
How many RS-232 drivers and receivers does MAX3232CDWG4 have?
The MAX3232CDWG4 contains two RS-232 line drivers and two line receivers, giving it a 2/2 transceiver configuration. The Texas Instruments datasheet describes it as a multichannel RS-232 line driver/receiver. It can therefore support two transmit paths and two receive paths, including a full-duplex point-to-point serial connection using one driver and one receiver.
What is the maximum data rate of MAX3232CDWG4?
The MAX3232CDWG4 operates to 250 kbit/s. According to the Texas Instruments device documentation, this rate supports substantially faster data transfer than a conventional low-speed RS-232 implementation. The figure is a maximum operating rate, so cable length, capacitance, baud-rate division, and the connected system must also be considered during interface design.
Does MAX3232CDWG4 include ESD protection?
Yes. The MAX3232CDWG4 provides ±15 kV human-body-model ESD protection. According to the Texas Instruments datasheet information, the device meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28. Connector-side protection should still be evaluated as part of the complete system because cable transients and ESD events can exceed the ratings of any single interface component.
Where can I download the MAX3232CDWG4 datasheet PDF?
The MAX3232CDWG4 datasheet PDF is available through the Texas Instruments documentation listing identified for this part and through the linked all-datasheet document page. The manufacturer document identifies a 27-page MAX3232 data sheet for the family. Use the manufacturer pin-description table and electrical-characteristics sections to assign PCB nets and verify operating limits before releasing a design.
Where can I find the MAX3232CDWG4 pinout?
The MAX3232CDWG4 uses a 16-pin SOIC, and its complete numbered pin assignment appears in the pin-description table of the Texas Instruments MAX3232 family datasheet. The document also shows the charge-pump capacitor connections. Assign connector-side driver and receiver pins only after comparing the schematic symbols and package drawing, because SOIC lead numbering is not arranged in the same visual order as the physical pins.
What external capacitors does MAX3232CDWG4 require?
The MAX3232CDWG4 requires four external 0.1 µF capacitors to support its dual charge-pump supply. According to the Texas Instruments family documentation, these capacitors are part of the normal operating circuit rather than optional bypass components. Keep each capacitor adjacent to the corresponding IC pin, use the specified capacitance and voltage rating, and provide a low-impedance ground connection.
What is the best drop-in replacement for MAX3232CDWG4?
The MAX3232EIDWR is the closest documented same-manufacturer replacement because Texas Instruments identifies MAX3232E as an improved direct drop-in replacement for MAX3232 in new designs, and both use a 16-pin SOIC footprint. MAX3232IDW and MAX3232CDE4 are also SOIC-16 candidates, while SN65C3232D provides a cross-brand option. Verify pin-level enable, fail-safe, and timing behavior before production substitution.
Can SN65C3232D replace MAX3232CDWG4?
SN65C3232D can be considered as a cross-brand 16-pin RS-232 replacement candidate because it also provides two drivers, two receivers, a dual charge pump, and ±15 kV ESD protection. According to the comparison information, its serial-port connections, including ground, are intended to be pin-to-pin compatible with the MAX3232 family. Production approval should still include a board-level review of every pin and the application’s ESD requirements.
What is the difference between MAX3232CDWG4 and MAX3232EIDWR?
The principal documented difference is that Texas Instruments identifies MAX3232E as an improved direct replacement for MAX3232 in new designs. Both MAX3232CDWG4 and MAX3232EIDWR use a 16-pin SOIC package and implement a 2/2 RS-232 transceiver. For a drop-in decision, compare the exact receiver fail-safe state, driver enable arrangement, ESD rating, and data-rate limits in each datasheet before substituting the E variant.
MAX3232CDWG4 vs MAX3232IDW: which is better for a new design?
MAX3232CDWG4 is the appropriate choice when the documented 3 V to 5.5 V supply range, 250 kbit/s operation, 2/2 channel count, and ±15 kV HBM protection match the design. MAX3232IDW is a 16-pin SOIC alternative that may suit an existing qualified BOM, but its exact electrical and fail-safe behavior must be checked against the target circuit. For new designs, the manufacturer recommendation favors the improved MAX3232E family.
When should I choose MAX3232CDWG4 instead of MAX3232EIDWR?
Choose MAX3232CDWG4 when an existing design specifically requires the MAX3232CD function, a 0°C to 70°C commercial temperature grade, and the documented 250 kbit/s operating rate. Choose MAX3232EIDWR when starting a new design that benefits from the manufacturer’s improved MAX3232E replacement path. Because both use SOIC-16, the mechanical footprint is not the deciding factor; functional behavior and qualification requirements are.
Is MAX3232CDWG4 suitable for industrial equipment?
MAX3232CDWG4 can be used in industrial equipment when the enclosure temperature remains within its documented 0°C to 70°C operating range and the interface does not require an extended-temperature grade. Its 3 V to 5.5 V supply tolerance and ±15 kV HBM protection are useful in controlled industrial systems. For wider ambient ranges, select a part explicitly rated for the required temperature.
How do I check MAX3232CDWG4 stock and lead time?
Use the Request a Quote form on this page to request current stock, minimum order quantity, packaging, and lead time for MAX3232CDWG4. The form gives the purchasing team a single channel for an up-to-date quotation and production schedule. Commit to an allocation only after the manufacturer confirms the exact MAX3232CDWG4 ordering code and delivery terms.
What is the price of MAX3232CDWG4?
Request the current MAX3232CDWG4 quotation through the Request a Quote form on this page. The form can provide pricing for the exact ordering code, package, and production quantity while keeping commercial terms connected to current supply. Stock and lead time should be confirmed in the same request because both can change independently of a quotation.
Where to buy MAX3232CDWG4 online?
Submit the MAX3232CDWG4 request through the Request a Quote form on this page for current commercial availability and allocation information. The form supports a direct inquiry for the exact 16-pin SOIC device rather than a generic RS-232 transceiver. Include the target quantity, packaging preference, and required delivery date in the request.

Data referensi kejuruteraan untuk MAX3232CDWG4 — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose MAX3232CDWG4 when the design requires a 2/2 RS-232 transceiver, a 3 V to 5.5 V supply, up to 250 kbit/s, ±15 kV HBM protection, and a commercial 0°C to 70°C temperature range in a 16-pin SOIC footprint. Choose MAX3232EIDWR for a new design because Texas Instruments identifies MAX3232E as an improved direct replacement for MAX3232. Use MAX3232IDW or MAX3232CDE4 when an existing qualified design uses those orderable variants and their pin-level behavior has been reviewed. Consider SN65C3232D as a cross-brand option after checking receiver fail-safe behavior, enable functions, capacitor connections, and operating limits. A shared package does not by itself establish drop-in compatibility, so validate every connection and power-up state before releasing an alternative into production.

Perbandingan dengan Gantian

Parametr Produk Ini MAX3232EIDWR MAX3232IDW MAX3232CDE4 SN65C3232D
Package SOIC-16 SOIC-16 SOIC-16 SOIC-16 SOIC-16
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Device Type RS-232 transceiver RS-232 transceiver RS-232 transceiver RS-232 transceiver RS-232 transceiver
Drivers / Receivers 2/2 2/2 2/2 2/2 2/2

Penyeberangsung Jelas

  • Manufacturer-backed direct-replacement path (vsMAX3232EIDWR)
  • Documented commercial 250 kbit/s interface (vsSN65C3232D)
  • Established two-channel integration (vsMAX3232IDW)
  • Required charge-pump network is fully defined (vsMAX3232CDE4)

Catatan Desain

Place the four required 0.1 µF charge-pump capacitors close to the associated MAX3232CDWG4 pins and route their return paths directly to the device ground. Keep the capacitor loops compact because these components support the switched voltage conversion that produces the RS-232 signal levels. Avoid placing sensitive analog traces between the charge-pump nodes and the ground plane, and verify the physical pin orientation against the SOIC-16 drawing before assigning PCB nets.

Treat each RS-232 connection as a point-to-point interface with a shared signal-ground reference. Route driver outputs directly to their connectors and receivers back to the controller rather than creating a bus with multiple drivers. Check the host and peripheral logic polarity because the TX-to-RX naming convention is not consistent across equipment. Keep the cable away from clocks, switching power nodes, relay contacts, and other high-noise sources to prevent errors in both directions.

Do not substitute a mechanically similar SOIC-16 transceiver solely from its package description. Compare every pin for driver and receiver assignment, charge-pump capacitor connections, enable behavior, fail-safe receiver state, supply range, data rate, and ESD rating. A valid footprint match establishes mechanical compatibility only. After substitution, rerun power-up, logic-level, cable-length, baud-rate, and electrostatic-discharge validation on the assembled board.

The internal charge pump creates fast current transitions while producing the bipolar RS-232 voltages. Keep the four external capacitors near the package, avoid extending those connections, and provide a quiet ground reference. Position the RS-232 connector away from precision analog sections, and maintain physical separation between the transceiver area and high-current switching equipment. If radiated emissions become difficult to control, verify capacitor selection, ground-plane continuity, connector shielding, and cable construction with EMI measurements.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Yes
Bosong halogen
Unknown
Mineral konflik
Unknown

The component is identified as lead free. RoHS, REACH, halogen-free, conflict-minerals, and automotive-qualification status require confirmation from the current manufacturer declaration.

Data disahkan pada: 2026-11-09 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

MAX3232CDWG4 datasheet MAX3232CDWG4 pinout MAX3232CDWG4 datasheet pdf MAX3232CDWG4 equivalent MAX3232CDWG4 replacement MAX3232CDWG4 drop-in replacement MAX3232CDWG4 vs MAX3232EIDWR MAX3232CDWG4 footprint MAX3232CDWG4 price MAX3232CDWG4 stock Texas Instruments MAX3232CDWG4 MAX3232CDWG4 250 kbit/s RS-232 MAX3232CDWG4 SOIC-16 pinout MAX3232CDWG4 application circuit

Komponen dan Tanda berkaitan

Texas Instruments MAX3232CDWG4 MAX3232EIDWR MAX3232IDW MAX3232CDE4 SN65C3232D RS-232 transceiver line driver line receiver interface IC RS-232 CMOS TIA/EIA-232-F ITU V.28 dual charge pump ESD protection ±15 kV HBM 250 kbit/s 3 V to 5.5 V supply SOIC-16 surface mount point-to-point serial communication charge-pump capacitor
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ