MAX3232CDWG4 - Dual RS-232 Transceiver | Texas Instruments
MPN: MAX3232CDWG4 ✓ Hoạt độngMAX3232CDWG4 Tóm tắt
An RS-232 transceiver is an interface IC that bridges the voltage-domain difference between CMOS or other digital logic and the bipolar signal levels used by RS-232 equipment. Within the interface hierarchy, the MAX3232CDWG4 is a multichannel line transceiver containing RS-232 line drivers, RS-232 receivers, and a dual charge-pump power supply. That internal hierarchy also explains why four external 0.1 µF capacitors are used to generate the required positive and negative RS-232 voltage levels.
The principal benefits are operation from a single 3 V to 5.5 V supply, two transmit channels, two receive channels, a maximum data rate of 250 kbit/s, and ±15 kV HBM ESD protection. The MAX3232 family meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28 as identified in the device documentation. These characteristics make the part suitable for industrial control, instrumentation, POS equipment, and embedded serial-port designs.
Technically, the charge-pump circuitry converts the single positive supply into the voltage swings required by RS-232 drivers. The receiver side detects differential bipolar inputs and translates them into CMOS-compatible logic levels. The MAX3232CDWG4 is a commercial-temperature option, while the MAX3232E family is identified by Texas Instruments as an improved direct replacement for MAX3232 in new designs. Circuit designers should nevertheless compare device-specific enable, fail-safe, and power-control behavior before approving a substitute.
Typical uses include connecting an embedded controller to a legacy printer, barcode reader, test instrument, or industrial peripheral over a full-duplex RS-232 link. The 16-pin SOIC package is also practical for designs that already use surface-mount assembly and can accommodate the external charge-pump capacitor network. Because the line interface is not a differential CAN or RS-485 bus, the interconnect should be implemented as a point-to-point RS-232 connection with the required signal-ground reference.
A key design consideration is capacitor placement. Position the four 0.1 µF charge-pump capacitors close to their associated device pins, with the shortest possible ground-return paths. Protect exposed connector-side pins against electrostatic discharge, provide a stable ground reference, and route the RS-232 cable away from sensitive analog and high-speed digital traces.
This product page consolidates the device specifications, verified sourcing links, drop-in comparison information, application guidance, and practical layout considerations into one engineering-focused reference. It helps distinguish electrical equivalents from mechanically similar parts and highlights the checks required before reusing an existing 16-pin SOIC layout.
Bộ thay thế dễ dàng lắp đặt cho MAX3232CDWG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MAX3232EIDWR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3232IDW
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232CDE4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SN65C3232D
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3232CDWG4 Thông số kỹ thuật
| Device Type | 2/2 RS-232 line transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| ESD Protection | ±15 kV HBM |
| External Charge-Pump Capacitors | 4 × 0.1 µF |
| RS-232 Compliance | TIA/EIA-232-F and ITU V.28 |
| Logic Technology | CMOS |
| Khoảng nhiệt độ hoạt động | 0°C to 70°C |
| Hộp | 16-pin SOIC |
| Package Width | 7.50 mm |
| Package Body Length | 0.295 inch |
| Kiểu lắp đặt | Surface mount |
| Temperature Grade | Commercial |
| Lead-Free Status | Lead free |
Hướng dẫn cấu hình chân MAX3232CDWG4 0.295 inch
Cấu hình chân cho MAX3232CDWG4 (0.295 inch gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3232CDWG4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3232CDWG4 phù hợp cho 6 Áp dụngs: Embedded Controller Serial Interface, Industrial Serial Instrument, Point-of-Sale Terminal Interface, Printer and Barcode Reader Connectivity, RS-232-to-Logic Bridge, Communication and Network Appliance.
Embedded Controller Serial Interface
The MAX3232CDWG4 suits an embedded controller that must communicate with a legacy peripheral over a point-to-point RS-232 link. Its 3 V to 5.5 V supply range allows operation from common 3.3 V or 5 V logic rails, while the 2/2 arrangement supports two transmit and two receive functions. A 250 kbit/s maximum rate accommodates conventional serial-console, configuration, and service protocols. The circuit should use one driver and one receiver for full-duplex communication, with the RS-232 ground connected to the equipment signal ground. Four 0.1 µF charge-pump capacitors remain mandatory, and their placement should be treated as part of the high-frequency layout rather than as optional decoupling.
Được đề xuất
Industrial Serial Instrument
MAX3232CDWG4 can provide the electrical interface between a controller and an RS-232 test or measurement instrument. The commercial 0°C to 70°C rating is appropriate for controlled indoor equipment, and ±15 kV HBM protection adds a useful robustness margin on the logic and connector-related pins. At a maximum 250 kbit/s, the link can support instrument command and response traffic without relying on long-distance high-speed guarantees. Use a point-to-point cable arrangement, connect signal ground, and keep the transceiver’s charge-pump nodes away from sensitive analog inputs. Connector-side protection and enclosure grounding remain part of the overall surge and ESD design.
Được đề xuất
Point-of-Sale Terminal Interface
The MAX3232CDWG4 is suitable for point-of-sale equipment that connects a controller board to a printer, customer display, scanner, or other legacy RS-232 peripheral. Its two drivers and two receivers allow multiple unidirectional links or a full-duplex primary port, while its single 3 V to 5.5 V supply simplifies integration with embedded systems operating at either 3.3 V or 5 V. The 250 kbit/s capability is more than adequate for many peripheral-control protocols. Keep external cables away from processor clocks and switching supplies, use the device ground as the signal reference, and place the four required 0.1 µF capacitors directly beside the charge-pump pins to minimize switching transients.
Được đề xuất
Printer and Barcode Reader Connectivity
A pair of MAX3232CDWG4 channels can connect a control board to a receipt printer and a barcode reader without using separate single-driver and single-receiver devices. The interface operates from a 3 V to 5.5 V supply and provides two drivers and two receivers at up to 250 kbit/s, which supports common printer and scanner command formats. Because RS-232 uses bipolar signaling and a ground reference, verify cable pin assignments and logic polarity at the connector rather than assuming that TX and RX names always match. Provide adequate separation from motors and relay coils, and route the four charge-pump capacitors close to the transceiver to prevent radiated disturbance from the switched capacitor supply.
Được đề xuất
RS-232-to-Logic Bridge
MAX3232CDWG4 can bridge CMOS-level controller signals and the bipolar RS-232 interface used by older equipment. The receiver translates RS-232 levels into logic-compatible signals, while the driver produces the required positive and negative swing from the 3 V to 5.5 V system supply. Its 2/2 configuration permits either one bidirectional link with spare channels or two point-to-point links. The ±15 kV HBM protection rating should be considered when selecting connectors and enclosure grounding, but it does not replace cable surge protection. Confirm the receiver’s logic state during power transitions and verify that the host software uses the same baud rate and signal polarity.
Được đề xuất
Communication and Network Appliance
MAX3232CDWG4 is useful in communication equipment that retains a service, configuration, or management connector implemented with RS-232. The 16-pin SOIC package simplifies surface-mount assembly, and the 2/2 arrangement can manage more than one serial function without duplicating the charge-pump circuitry. A 250 kbit/s maximum rate supports management and firmware-transfer traffic. In a network appliance, isolate the RS-232 connector from chassis and logic ground according to the system’s grounding policy, and protect the cable entry against electrostatic discharge. Keep the charge-pump capacitor loop compact and ensure the 0°C to 70°C commercial operating range is maintained inside the enclosure.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3232CDWG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3232EIDWR | MAX3232IDW | MAX3232CDE4 | SN65C3232D |
|---|---|---|---|---|---|
| Package | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Drivers / Receivers | 2/2 | 2/2 | 2/2 | 2/2 | 2/2 |
Bảo phân biệt quan trọng
- Manufacturer-backed direct-replacement path (vsMAX3232EIDWR)
- Documented commercial 250 kbit/s interface (vsSN65C3232D)
- Established two-channel integration (vsMAX3232IDW)
- Required charge-pump network is fully defined (vsMAX3232CDE4)
Ghi chú thiết kế
Place the four required 0.1 µF charge-pump capacitors close to the associated MAX3232CDWG4 pins and route their return paths directly to the device ground. Keep the capacitor loops compact because these components support the switched voltage conversion that produces the RS-232 signal levels. Avoid placing sensitive analog traces between the charge-pump nodes and the ground plane, and verify the physical pin orientation against the SOIC-16 drawing before assigning PCB nets.
Treat each RS-232 connection as a point-to-point interface with a shared signal-ground reference. Route driver outputs directly to their connectors and receivers back to the controller rather than creating a bus with multiple drivers. Check the host and peripheral logic polarity because the TX-to-RX naming convention is not consistent across equipment. Keep the cable away from clocks, switching power nodes, relay contacts, and other high-noise sources to prevent errors in both directions.
Do not substitute a mechanically similar SOIC-16 transceiver solely from its package description. Compare every pin for driver and receiver assignment, charge-pump capacitor connections, enable behavior, fail-safe receiver state, supply range, data rate, and ESD rating. A valid footprint match establishes mechanical compatibility only. After substitution, rerun power-up, logic-level, cable-length, baud-rate, and electrostatic-discharge validation on the assembled board.
The internal charge pump creates fast current transitions while producing the bipolar RS-232 voltages. Keep the four external capacitors near the package, avoid extending those connections, and provide a quiet ground reference. Position the RS-232 connector away from precision analog sections, and maintain physical separation between the transceiver area and high-current switching equipment. If radiated emissions become difficult to control, verify capacitor selection, ground-plane continuity, connector shielding, and cable construction with EMI measurements.
Thông tin tuân thủ
The component is identified as lead free. RoHS, REACH, halogen-free, conflict-minerals, and automotive-qualification status require confirmation from the current manufacturer declaration.