MAX3483EESA+T - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
MPN: MAX3483EESA+T ✓ AktifMAX3483EESA+T Ringkasan
An RS-485/RS-422 transceiver is an interface integrated circuit that converts logic-level signals between a host controller and a balanced differential bus. These differential interfaces use two conductors and common-mode rejection to improve noise immunity over longer cable runs. The MAX3483EESA+T sits within the interface IC hierarchy as a physical-layer transceiver for industrial control, instrumentation, building automation, and embedded serial networking systems.
The device operates from a 3.3 V supply, with a documented operating range of 3 V to 3.6 V. Its ±15 kV ESD protection helps protect the bus-facing pins from electrostatic discharge encountered during installation or industrial operation. The 12 Mbps maximum signaling rate supports communication rates substantially above common low-speed RS-485 systems, while slew-rate-limited driver behavior reduces edge-rate harmonics on the cable.
Each device contains one driver and one receiver, allowing it to serve as a half-duplex RS-485 node when the driver and receiver direction are controlled appropriately. The MAX3483 family is also identified as a true RS-485/RS-422 transceiver, distinguishing its differential bus implementation from unrelated serial-interface standards. The 8-pin NSOIC package supports conventional surface-mount assembly while keeping the transceiver compact for multi-channel interface boards.
Typical uses include industrial sensor gateways, programmable logic controller communication ports, building-control equipment, instrumentation, and isolated or non-isolated serial data links. In a multi-drop RS-485 network, the transceiver interfaces a microcontroller UART with a polarity-balanced pair while the system's termination and biasing network determines signal integrity and load capability.
Board design should preserve the relationship between the differential pair, the transceiver ground reference, and the logic interface. Place input and bypass capacitors close to the power pin, route the driver outputs as a controlled-impedance differential pair, and verify termination, common-mode range, and cable length against the system data rate. The slew rate is intentionally limited, so the 12 Mbps specification should not be interpreted as a guarantee of reliable 12 Mbps operation over every cable length or topology.
This product page combines manufacturer specifications, commercial sourcing information, strict drop-in alternatives, package details, and practical PCB-design guidance. It also highlights the distinctions between the MAX3483E and related low-power MAX3485E, MAX3488E, and MAX3490E transceivers so engineers can identify a replacement without overlooking bus topology, speed, enable logic, or ESD requirements.
Pilihan pengganti yang segera untuk MAX3483EESA+T — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MAX3483EESA+T (sama faktor bentuk dan kaki) — berbeza dalam Package, Maximum Data Rate, Supported Standards, Driver Type, Product Type.
MAX3485EESA+T
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →MAX3488EESA+T
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →MAX3490EESA+T
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →MAX3483ESA+T
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →MAX3488EASA+T
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
MAX3483EESA+T Spesifikasi
| Product Type | RS-485/RS-422 transceiver |
| Transceiver Configuration | 1 driver and 1 receiver |
| Tegangan Pemberi Arus | 3.3 V |
| Tegangan Pemberi Arus Operasi | 3 V to 3.6 V |
| Maximum Data Rate | 12 Mbps |
| ESD Protection | ±15 kV |
| Driver Type | Slew-rate-limited true driver |
| Supported Standards | RS-485 and RS-422 |
| Duplex Mode | Half-duplex |
| Kemasan | 8-pin NSOIC |
| Kiraan Pin | 8 pins |
| Jenis Pemasangan | Surface mount |
Konfigurasi Pin MAX3483EESA+T
| Pin 1 | RO — Receiver output |
| Pin 2 | /RE — Receiver enable, active low |
| Pin 3 | DE — Driver enable |
| Pin 4 | DI — Driver input |
| Pin 5 | GND — Ground |
| Pin 6 | Y — Noninverting driver output |
| Pin 7 | A — Noninverting receiver input |
| Pin 8 | VCC — Positive supply |
Aplikasi Biasa
MAX3483EESA+T patut untuk 6 aplikasis: Industrial PLC Serial Communication, Building Automation Sensor Gateway, Instrumentation and Data Acquisition, Robotics and Motor-Control Network, Industrial Sensor Network, Embedded Communication Port.
Industrial PLC Serial Communication
The MAX3483EESA+T fits an RS-485 port on a programmable logic controller or industrial controller that already uses a 3.3 V UART. Its 3 V to 3.6 V operating range, one-driver/one-receiver configuration, and 12 Mbps maximum data rate provide a compact interface between the controller logic and a balanced field bus. The ±15 kV ESD rating is useful when the cable connects to equipment outside the control cabinet. Configure the transceiver for half-duplex operation, apply the correct termination and fail-safe biasing, and treat 12 Mbps as a device capability rather than a guaranteed line rate for every cable topology.
Disebarkan
Building Automation Sensor Gateway
The MAX3483EESA+T is useful in a building-automation gateway that connects an MCU or module to a longer RS-485 lighting, HVAC, or access-control network. Its differential driver and receiver support reliable signaling over balanced wiring, while the slew-rate-limited output reduces high-frequency cable harmonics. The 3.3 V supply aligns with many embedded controllers, and 12 Mbps provides substantial protocol headroom. In practice, the designer should lower the baud rate for long cable runs, retain a common ground reference where permitted by the installation, and place termination only at the physical ends of the bus.
Disebarkan
Instrumentation and Data Acquisition
The MAX3483EESA+T can connect laboratory or process instrumentation to a data-acquisition controller through an RS-422 or RS-485 link. Differential signaling improves immunity to common-mode noise found around motors, relays, and switching power supplies, while the 12 Mbps capability supports high-speed digital acquisition or configuration traffic. The receiver output can operate directly from a compatible 3.3 V digital domain. Use separate routing for the sensitive receiver input and the cable-side driver output, and confirm that the connected instrument uses compatible logic levels and bus termination.
Disebarkan
Robotics and Motor-Control Network
The MAX3483EESA+T is appropriate for command and status links between a robot controller, remote drive electronics, and service modules when those subsystems communicate over RS-485. Its ±15 kV ESD protection helps the interface withstand discharge events associated with mobile equipment and cable handling. The 12 Mbps maximum rate is useful for deterministic command traffic, but motor noise and ground offsets can reduce usable distance, so shielded or twisted-pair wiring and conservative baud rates are recommended. The half-duplex control arrangement should ensure that only one transmitter drives the bus at a time.
Disebarkan
Industrial Sensor Network
The MAX3483EESA+T supports compact sensor nodes that use a 3.3 V microcontroller UART to report measurements over a shared RS-485 network. Its one-driver/one-receiver configuration supports a low-component-count half-duplex node, and 12 Mbps allows the protocol to exceed the throughput required by most temperature, pressure, and environmental sensors. ESD protection adds value for field-wired nodes, while slew-rate-limited drive helps limit cable emissions. The node should use address-based arbitration, fail-safe biasing, and endpoint termination so inactive receivers do not load the bus.
Disebarkan
Embedded Communication Port
The MAX3483EESA+T provides a compact differential communications port for an embedded controller, gateway, or programmable logic module with a 3.3 V UART. The device converts the UART's single-ended logic signals to the balanced RS-485 or RS-422 physical layer without requiring a separate line driver and receiver. A maximum rate of 12 Mbps gives firmware flexibility, while the 8-pin NSOIC package simplifies routing in compact assemblies. Enable and shutdown pins should be driven by a controller that guarantees correct bus turnaround and prevents contention when multiple nodes transmit.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MAX3483EESA+T — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MAX3485EESA+T | MAX3488EESA+T | MAX3490EESA+T |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin NSOIC | 8-pin NSOIC | 8-pin NSOIC | 8-pin NSOIC |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Bus Standards | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
| Number of Pins | 8 pins | 8 pins | 8 pins | 8 pins |
Penyeberangsung Jelas
- Direct MAX3483E-family behavior with a defined 12 Mbps maximum rate (vsMAX3485EESA+T)
- Half-duplex one-driver/one-receiver implementation in a compact 8-pin NSOIC package (vsMAX3488EESA+T)
- MAX3483E-family pin and interface continuity for existing designs (vsMAX3483ESA+T)
Catatan Desain
Route the Y and A bus conductors as a closely coupled differential pair rather than as unrelated point-to-point traces. Keep the pair away from switching nodes and motor-drive traces, minimize stub lengths, and use the same reference plane where practical. Place the transceiver close to the connector so ESD current has a short path to the protective structure and ground. Add the termination resistor at the physical bus endpoint rather than at every node.
Do not enable the driver while another node is transmitting. The MAX3483EESA+T uses driver and receiver enable controls for half-duplex communication, and incorrect timing can produce bus contention, excess current, or corrupted data. Validate the enable polarity in the manufacturer truth table and firmware. When /RE and DE are tied for echo control, allow adequate settling time before interpreting receiver data.
The 12 Mbps figure is the maximum device signaling capability, not a guaranteed cable length. Estimate rise time and attenuation from the selected transceiver, cable, connectors, and topology, then select a lower baud rate when necessary. Use twisted-pair wiring, correct common-mode grounding, and fail-safe biasing so an idle or disconnected bus produces a defined receiver state. Avoid excessive termination when multiple branches or unusually short cables are present.
Place the supply bypass capacitor immediately between VCC and GND, with a short ground return and minimal loop area. Route the connector-facing bus pins away from sensitive logic so transient current does not pass through the logic ground region. Verify the power rail remains within 3 V to 3.6 V under noise and load transients; excessive supply noise can reduce receiver margin even when the cable wiring is correct.
Maklumat Kesediaan
The manufacturer product page identifies the MAX3483E family as production. RoHS, REACH, halogen-free, conflict-minerals, and automotive qualification status require confirmation from the current manufacturer product documentation or declaration.