Analog Devices

MAX3483EESA+T - 12Mbps RS-485/RS-422 Transceiver | Analog Devices

MPN: MAX3483EESA+T ✓ פעיל
3.3 V Vdss RS-485 and RS-422 Rds(on) 8-pin NSOIC Package
כמות הזמנה מינימלית: 1 |

MAX3483EESA+T סקירה

Analog Devices MAX3483EESA+T is a 3.3 V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 12 Mbps, ±15 kV ESD protection, and an 8-pin NSOIC package. The MAX3483E family combines true RS-485/RS-422 signal handling with slew-rate-limited drivers to reduce unwanted reflections and electromagnetic interference on balanced communication lines.

An RS-485/RS-422 transceiver is an interface integrated circuit that converts logic-level signals between a host controller and a balanced differential bus. These differential interfaces use two conductors and common-mode rejection to improve noise immunity over longer cable runs. The MAX3483EESA+T sits within the interface IC hierarchy as a physical-layer transceiver for industrial control, instrumentation, building automation, and embedded serial networking systems.

The device operates from a 3.3 V supply, with a documented operating range of 3 V to 3.6 V. Its ±15 kV ESD protection helps protect the bus-facing pins from electrostatic discharge encountered during installation or industrial operation. The 12 Mbps maximum signaling rate supports communication rates substantially above common low-speed RS-485 systems, while slew-rate-limited driver behavior reduces edge-rate harmonics on the cable.

Each device contains one driver and one receiver, allowing it to serve as a half-duplex RS-485 node when the driver and receiver direction are controlled appropriately. The MAX3483 family is also identified as a true RS-485/RS-422 transceiver, distinguishing its differential bus implementation from unrelated serial-interface standards. The 8-pin NSOIC package supports conventional surface-mount assembly while keeping the transceiver compact for multi-channel interface boards.

Typical uses include industrial sensor gateways, programmable logic controller communication ports, building-control equipment, instrumentation, and isolated or non-isolated serial data links. In a multi-drop RS-485 network, the transceiver interfaces a microcontroller UART with a polarity-balanced pair while the system's termination and biasing network determines signal integrity and load capability.

Board design should preserve the relationship between the differential pair, the transceiver ground reference, and the logic interface. Place input and bypass capacitors close to the power pin, route the driver outputs as a controlled-impedance differential pair, and verify termination, common-mode range, and cable length against the system data rate. The slew rate is intentionally limited, so the 12 Mbps specification should not be interpreted as a guarantee of reliable 12 Mbps operation over every cable length or topology.

This product page combines manufacturer specifications, commercial sourcing information, strict drop-in alternatives, package details, and practical PCB-design guidance. It also highlights the distinctions between the MAX3483E and related low-power MAX3485E, MAX3488E, and MAX3490E transceivers so engineers can identify a replacement without overlooking bus topology, speed, enable logic, or ESD requirements.

חלופות תחליף ישיר עבור MAX3483EESA+T — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם MAX3483EESA+T (אותו גורם צורה וטביעת רגל) — שונים ב Package, Maximum Data Rate, Supported Standards, Driver Type, Product Type.

Maxim Integrated
Package: 8-SOIC
Maximum Data Rate: 10 Mbps
השווה עם MAX3483EESA+T →
Analog Devices
Package: 8-SOIC, 8 pins
Maximum Data Rate: 10 Mbps
Driver Type: Slew-rate-limited true differential driver
השווה עם MAX3483EESA+T →
Analog Devices
Package: 8-pin SOIC
Maximum Data Rate: 12Mbps
Supported Standards: RS-422 and RS-485
השווה עם MAX3483EESA+T →
Analog Devices
Package: 8-pin SOIC
השווה עם MAX3483EESA+T →
Analog Devices
Package: 8-pin SOIC
Maximum Data Rate: 12Mbps
Supported Standards: True RS-485 and RS-422
השווה עם MAX3483EESA+T →

MAX3485EESA+T

✅ Drop-In ⚠️ מפרטים לא מאומתים
Analog Devices
📦 8-pin NSOIC
1/1 RS-422/RS-485 transceiver · 3V to 3.6V · 12Mbps · ±15kV · 1 driver · 1 receiver · RS-422 and RS-485 · Half-duplex

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

MAX3488EESA+T

✅ Drop-In ⚠️ מפרטים לא מאומתים
Analog Devices
📦 8-pin NSOIC
RS-485/RS-422 transceiver · 3.3 V · 3 V to 3.6 V · 12 Mbps · ±15 kV · 1 driver · 1 receiver · RS-485 and RS-422

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

MAX3490EESA+T

✅ Drop-In ⚠️ מפרטים לא מאומתים
Analog Devices
📦 8-pin NSOIC
RS-485/RS-422 transceiver · 1 transmitter and 1 receiver · 3.0V to 3.6V · 12Mbps · 10Mbps · ±15kV · Slew-rate-limited · True RS-485 and RS-422

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

MAX3483ESA+T

✅ Drop-In ⚠️ מפרטים לא מאומתים
Analog Devices
📦 8-pin NSOIC
RS-485/RS-422 transceiver · 3.3 V · 10 Mbps · Up to 250 kbps · 1 driver · 1 receiver · Half-duplex · RS-485 and RS-422

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

MAX3488EASA+T

✅ Drop-In ⚠️ מפרטים לא מאומתים
📦 8-pin NSOIC
Same 8-pin footprint and 12 Mbps-class MAX3488E operation; the A suffix differs from the E temperature or grade code

📋 חלופה להתייחסות (לא בקטלוג)

MAX3483EESA+T מפרטים

Product Type RS-485/RS-422 transceiver
Transceiver Configuration 1 driver and 1 receiver
מתח אספקה 3.3 V
מתח אספקה פעיל 3 V to 3.6 V
Maximum Data Rate 12 Mbps
ESD Protection ±15 kV
Driver Type Slew-rate-limited true driver
Supported Standards RS-485 and RS-422
Duplex Mode Half-duplex
מארז 8-pin NSOIC
מספר פינים 8 pins
סוג הרכבה Surface mount

תצורת פינים של MAX3483EESA+T

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
פין 1 RO — Receiver output
פין 2 /RE — Receiver enable, active low
פין 3 DE — Driver enable
פין 4 DI — Driver input
פין 5 GND — Ground
פין 6 Y — Noninverting driver output
פין 7 A — Noninverting receiver input
פין 8 VCC — Positive supply

יישומים טיפוסיים

MAX3483EESA+T מתאים עבור 6 יישוםs: Industrial PLC Serial Communication, Building Automation Sensor Gateway, Instrumentation and Data Acquisition, Robotics and Motor-Control Network, Industrial Sensor Network, Embedded Communication Port.

🏭

Industrial PLC Serial Communication

The MAX3483EESA+T fits an RS-485 port on a programmable logic controller or industrial controller that already uses a 3.3 V UART. Its 3 V to 3.6 V operating range, one-driver/one-receiver configuration, and 12 Mbps maximum data rate provide a compact interface between the controller logic and a balanced field bus. The ±15 kV ESD rating is useful when the cable connects to equipment outside the control cabinet. Configure the transceiver for half-duplex operation, apply the correct termination and fail-safe biasing, and treat 12 Mbps as a device capability rather than a guaranteed line rate for every cable topology.

🏠

Building Automation Sensor Gateway

The MAX3483EESA+T is useful in a building-automation gateway that connects an MCU or module to a longer RS-485 lighting, HVAC, or access-control network. Its differential driver and receiver support reliable signaling over balanced wiring, while the slew-rate-limited output reduces high-frequency cable harmonics. The 3.3 V supply aligns with many embedded controllers, and 12 Mbps provides substantial protocol headroom. In practice, the designer should lower the baud rate for long cable runs, retain a common ground reference where permitted by the installation, and place termination only at the physical ends of the bus.

📟

Instrumentation and Data Acquisition

The MAX3483EESA+T can connect laboratory or process instrumentation to a data-acquisition controller through an RS-422 or RS-485 link. Differential signaling improves immunity to common-mode noise found around motors, relays, and switching power supplies, while the 12 Mbps capability supports high-speed digital acquisition or configuration traffic. The receiver output can operate directly from a compatible 3.3 V digital domain. Use separate routing for the sensitive receiver input and the cable-side driver output, and confirm that the connected instrument uses compatible logic levels and bus termination.

🤖

Robotics and Motor-Control Network

The MAX3483EESA+T is appropriate for command and status links between a robot controller, remote drive electronics, and service modules when those subsystems communicate over RS-485. Its ±15 kV ESD protection helps the interface withstand discharge events associated with mobile equipment and cable handling. The 12 Mbps maximum rate is useful for deterministic command traffic, but motor noise and ground offsets can reduce usable distance, so shielded or twisted-pair wiring and conservative baud rates are recommended. The half-duplex control arrangement should ensure that only one transmitter drives the bus at a time.

🧩

Industrial Sensor Network

The MAX3483EESA+T supports compact sensor nodes that use a 3.3 V microcontroller UART to report measurements over a shared RS-485 network. Its one-driver/one-receiver configuration supports a low-component-count half-duplex node, and 12 Mbps allows the protocol to exceed the throughput required by most temperature, pressure, and environmental sensors. ESD protection adds value for field-wired nodes, while slew-rate-limited drive helps limit cable emissions. The node should use address-based arbitration, fail-safe biasing, and endpoint termination so inactive receivers do not load the bus.

🖥️

Embedded Communication Port

The MAX3483EESA+T provides a compact differential communications port for an embedded controller, gateway, or programmable logic module with a 3.3 V UART. The device converts the UART's single-ended logic signals to the balanced RS-485 or RS-422 physical layer without requiring a separate line driver and receiver. A maximum rate of 12 Mbps gives firmware flexibility, while the 8-pin NSOIC package simplifies routing in compact assemblies. Enable and shutdown pins should be driven by a controller that guarantees correct bus turnaround and prevents contention when multiple nodes transmit.

What is the MAX3483EESA+T?
The MAX3483EESA+T is a 3.3 V, half-duplex RS-485/RS-422 transceiver containing one driver and one receiver. According to the Analog Devices MAX3483E data sheet Rev. 1, it supports signaling up to 12 Mbps, includes ±15 kV ESD protection, and uses a slew-rate-limited true driver. The device is packaged in an 8-pin NSOIC for surface-mounted industrial and embedded communication designs.
What are the key specifications of MAX3483EESA+T that engineers should know?
The key MAX3483EESA+T specifications are a 3.3 V nominal supply, a 3 V to 3.6 V operating range, 12 Mbps maximum data rate, ±15 kV ESD protection, and one driver with one receiver. The Analog Devices MAX3483E data sheet Rev. 1 identifies the interface as a slew-rate-limited true RS-485/RS-422 transceiver in an 8-pin NSOIC package. These parameters define its bus-speed, protection, and board-layout requirements.
Where can I download the MAX3483EESA+T datasheet PDF?
The official MAX3483EESA+T documentation is available from the Analog Devices MAX3483E product page, which links to the manufacturer data sheet Rev. 1 and product documentation. Use that manufacturer document for the authoritative pin description, electrical characteristics, truth tables, and application circuit. The exact orderable suffix must remain MAX3483EESA+T, because package, temperature, and ordering codes distinguish it from related MAX3483 variants.
Where can I find the MAX3483EESA+T pinout?
The MAX3483EESA+T pinout is defined by the manufacturer data sheet Rev. 1 and corresponds to its 8-pin NSOIC configuration. The device uses one pin for supply, one for ground, driver input and enable control, receiver input and enable control, and the differential bus and receiver-output signals. Assign PCB nets from the package drawing and pin-description table rather than relying only on function names.
Is MAX3483EESA+T suitable for RS-485 networks?
Yes, the MAX3483EESA+T is specifically designed for true RS-485 and RS-422 communication. Its one-driver/one-receiver arrangement supports half-duplex RS-485 operation, and the Analog Devices MAX3483E data sheet Rev. 1 specifies a 12 Mbps maximum data rate. The system still needs correct bus termination, biasing, grounding, and suitable cable length for its selected baud rate.
What does the ±15 kV ESD protection on MAX3483EESA+T provide?
The ±15 kV rating identifies the ESD-protection level applied to the MAX3483EESA+T bus interface. According to the Analog Devices MAX3483E data sheet Rev. 1, the device is a ±15 kV ESD-protected transceiver. This rating strengthens its suitability for externally accessible industrial connections, although the complete interface still requires proper grounding, cable management, and protection coordination.
What is the difference between RS-485 and RS-422 operation with MAX3483EESA+T?
RS-485 supports a multidrop bus where multiple transceivers share a balanced pair, while RS-422 generally uses a point-to-point or one-driver-to-many-receiver arrangement. The MAX3483EESA+T supports both interfaces because its differential driver and receiver implement the required electrical signaling. Application-specific termination, biasing, topology, and grounding determine whether the physical connection is configured for RS-485 or RS-422.
MAX3483EESA+T vs MAX3485EESA+T: which is better for a 12 Mbps RS-485 link?
The MAX3483EESA+T is the better direct choice for a design centered on the MAX3483E family and a 12 Mbps maximum rate. The MAX3485EESA+T is identified as a 15 Mbps RS-485/RS-422 transceiver, giving it a 25% higher maximum signaling rate than the 12 Mbps MAX3483EESA+T. Both use an 8-pin NSOIC class of package, but enable logic and bus behavior should be checked before interchange.
When should I choose MAX3483EESA+T over MAX3485EESA+T?
Choose MAX3483EESA+T when the design requires the MAX3483E behavior, a 12 Mbps maximum rate, and the associated half-duplex RS-485/RS-422 interface. Choose MAX3485EESA+T when its higher 15 Mbps capability is useful and its bus-control requirements match the PCB. A higher headline data rate does not guarantee a shorter cable or better signal integrity at every installation.
Can MAX3485EESA+T replace MAX3483EESA+T?
The MAX3485EESA+T is a potential same-package replacement for the MAX3483EESA+T because both are 8-pin RS-485/RS-422 transceivers, but it is not automatically equivalent in every application. The MAX3485EESA+T supports up to 15 Mbps versus 12 Mbps for the MAX3483EESA+T, and enable or fail-safe behavior must also match. Confirm the manufacturer pin descriptions, receiver-output logic, and bus-controlling firmware before substitution.
What can replace MAX3483EESA+T on the same PCB?
The closest documented replacement candidates belong to the MAX3485E, MAX3488E, and MAX3490E low-power transceiver families, which use the same 8-pin NSOIC footprint. The MAX3485EESA+T offers 15 Mbps, while the MAX3488E and MAX3490E alternatives are considered for their respective receiver and bus-control characteristics. No verified cross-brand substitute was identified, so each candidate requires a pin-level and logic-level review.
Is there an Analog Devices MAX3483EESA+T replacement with the same 8-pin footprint?
The MAX3485EESA+T is the clearest Analog Devices alternative because it is an 8-pin RS-485/RS-422 transceiver rated for 15 Mbps instead of the MAX3483EESA+T's 12 Mbps. MAX3488EESA+T and MAX3490EESA+T are additional same-family candidates for evaluation. Pin-to-pin replacement still requires checking driver and receiver enable polarity, receiver output behavior, fail-safe response, and bus termination requirements.
What is the best alternative-brand equivalent for MAX3483EESA+T?
No alternative-brand equivalent can be confirmed as a drop-in replacement from the available manufacturer information. The MAX3483EESA+T uses a specific 8-pin half-duplex RS-485/RS-422 pinout with ±15 kV ESD protection and 12 Mbps operation, so a different manufacturer's part must be validated by pinout, supply voltage, enable logic, propagation delay, and fail-safe behavior. Use the Request a Quote form on this page when sourcing an approved alternate.
Where to buy MAX3483EESA+T online?
Use the Request a Quote form on this page to request the MAX3483EESA+T with the exact MAX3483EESA+T ordering suffix and the required delivery quantity. The form is the appropriate channel for current commercial availability, lot traceability, and quotation. Engineers should not substitute a different package code or temperature-grade suffix without confirming the full ordering-code and environmental requirements.
What is the price of MAX3483EESA+T?
Submit the MAX3483EESA+T part number and required quantity through the Request a Quote form on this page for the current quotation. Commercial terms can vary with quantity, sourcing channel, inventory status, and traceability requirements. This approach prevents a stale listing from being mistaken for a current firm quotation and keeps the inquiry tied to the exact MAX3483EESA+T orderable configuration.
What is the lead time and stock status for MAX3483EESA+T?
Request current stock, lead time, minimum order quantity, and lifecycle allocation through the Request a Quote form on this page. The Analog Devices product page identifies MAX3483E production, but production status does not by itself establish available inventory or a delivery interval for every order quantity. Include your required delivery date and acceptable packaging format with the inquiry.

נתוני עזר הנדסיים עבור MAX3483EESA+T — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the MAX3483EESA+T when maintaining an existing 8-pin MAX3483E circuit, using a 3.3 V RS-485 or RS-422 bus, and requiring a documented 12 Mbps maximum rate with ±15 kV ESD protection. Its half-duplex architecture suits multidrop RS-485 nodes and point-to-point RS-422 links with appropriate termination. Consider the MAX3485EESA+T when the PCB and firmware can accommodate its 15 Mbps rating and verified control behavior. Evaluate the MAX3488EESA+T or MAX3490EESA+T when their receiver, fail-safe, or enable characteristics better fit the system. Do not approve a substitute solely from the SOIC-8 outline: verify every pin, supply limits, logic thresholds, propagation timing, ESD rating, and bus-turnaround behavior before release.

השוואה עם חלופות

פרמטר מוצר זה MAX3485EESA+T MAX3488EESA+T MAX3490EESA+T
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Package 8-pin NSOIC 8-pin NSOIC 8-pin NSOIC 8-pin NSOIC
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V
Bus Standards RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422
Number of Pins 8 pins 8 pins 8 pins 8 pins

מבדילים עיקריים

  • Direct MAX3483E-family behavior with a defined 12 Mbps maximum rate (לעומתMAX3485EESA+T)
  • Half-duplex one-driver/one-receiver implementation in a compact 8-pin NSOIC package (לעומתMAX3488EESA+T)
  • MAX3483E-family pin and interface continuity for existing designs (לעומתMAX3483ESA+T)

הערות תכנון

Route the Y and A bus conductors as a closely coupled differential pair rather than as unrelated point-to-point traces. Keep the pair away from switching nodes and motor-drive traces, minimize stub lengths, and use the same reference plane where practical. Place the transceiver close to the connector so ESD current has a short path to the protective structure and ground. Add the termination resistor at the physical bus endpoint rather than at every node.

Do not enable the driver while another node is transmitting. The MAX3483EESA+T uses driver and receiver enable controls for half-duplex communication, and incorrect timing can produce bus contention, excess current, or corrupted data. Validate the enable polarity in the manufacturer truth table and firmware. When /RE and DE are tied for echo control, allow adequate settling time before interpreting receiver data.

The 12 Mbps figure is the maximum device signaling capability, not a guaranteed cable length. Estimate rise time and attenuation from the selected transceiver, cable, connectors, and topology, then select a lower baud rate when necessary. Use twisted-pair wiring, correct common-mode grounding, and fail-safe biasing so an idle or disconnected bus produces a defined receiver state. Avoid excessive termination when multiple branches or unusually short cables are present.

Place the supply bypass capacitor immediately between VCC and GND, with a short ground return and minimal loop area. Route the connector-facing bus pins away from sensitive logic so transient current does not pass through the logic ground region. Verify the power rail remains within 3 V to 3.6 V under noise and load transients; excessive supply noise can reduce receiver margin even when the cable wiring is correct.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The manufacturer product page identifies the MAX3483E family as production. RoHS, REACH, halogen-free, conflict-minerals, and automotive qualification status require confirmation from the current manufacturer product documentation or declaration.

הנתונים אומתו בתאריך: 2026-11-09 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

MAX3483EESA+T datasheet MAX3483EESA+T pinout MAX3483EESA+T datasheet pdf MAX3483EESA+T equivalent MAX3483EESA+T replacement MAX3483EESA+T cross reference MAX3483EESA+T vs MAX3485EESA+T MAX3483EESA+T footprint MAX3483EESA+T RS-485 transceiver MAX3483EESA+T application circuit Analog Devices MAX3483EESA+T MAX3483EESA+T price MAX3483EESA+T stock MAX3483EESA+T 12Mbps MAX3483EESA+T 8-SOIC

רכיבים ומונחים קשורים

Analog Devices Maxim Integrated MAX3483EESA+T MAX3483E MAX3485EESA+T MAX3488EESA+T MAX3490EESA+T RS-485 RS-422 transceiver interface IC physical-layer IC balanced differential signaling slew-rate-limited driver half-duplex communication 12 Mbps 3.3 V ±15 kV ESD protection NSOIC-8 SOIC surface mount industrial automation building automation data acquisition
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר