MC1455BP1G - 5/15V Single Timer | onsemi | DIP-8
MPN: MC1455BP1G ✓ AktifMC1455BP1G Ringkasan
A monolithic timer is a timing circuit that switches its output after a defined interval. The MC1455 family belongs to the timer and oscillator hierarchy within analog integrated circuits, combining a resistor-controlled timing network with an internal threshold comparator, trigger comparator, output latch, and discharge transistor. In astable mode, the output repeatedly charges and discharges an external capacitor; in monostable mode, one trigger event produces a single timed output pulse.
The MC1455BP1G supports supply voltages of 5 V and 15 V and provides separate trigger and reset terminals when those functions are needed. Its resistor-and-capacitor timing architecture allows the delay or oscillation frequency to be established with external components rather than an internal clock. This makes the device suitable for repeatable pulse generation, delay stages, tone generation, and periodic control functions.
The circuit combines analog timing thresholds with a logic-level output stage. During astable operation, the external capacitor voltage moves between the internal reference thresholds while the discharge transistor controls the resistor path. The resulting oscillation frequency and duty cycle depend on the selected resistance and capacitance values, so component tolerance directly affects timing accuracy. Monostable operation uses one triggering transition to initiate a single output pulse whose duration is controlled by one timing resistor and capacitor.
Typical applications include industrial pulse and delay circuits, oscillator modules, indicator flashing, periodic actuator control, signal-processing test equipment, and educational timer demonstrations. The -40°C to +85°C operating range supports industrial equipment, while the through-hole PDIP package simplifies hand assembly, prototyping, socketed construction, and replacement in legacy designs.
Designers should treat the trigger and reset inputs carefully because they influence internal state even when those functions are not used. Verify threshold and discharge-pin behavior against the manufacturer datasheet, maintain stable timing-component tolerances, and provide adequate decoupling between the supply pins and ground. The 5 V and 15 V supply designations should not be treated as a continuous operating range between those points without consulting the device limits.
This product record combines the manufacturer timing-circuit description with package, temperature, supply-voltage, and commercial information to support engineering selection. It also provides same-footprint replacement guidance, application-specific design considerations, and a parameter comparison intended to make PCB reuse decisions more transparent.
Pilihan pengganti yang segera untuk MC1455BP1G — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MC1455BP1G (sama faktor bentuk dan kaki) — berbeza dalam Mounting Type, Package, Number of Timers, Operating Modes, Product Type.
MC1455P1G
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →NE555N
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
NA555P
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
NE555P
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MC1455BP1G Spesifikasi
| Timer Type | 555 Type |
| Number of Timers | 1 timer |
| Operating Modes | Monostable and astable |
| Tegangan Pemberi Arus | 5 V or 15 V |
| Kemasan | 8-pin PDIP |
| Terminal Count | 8 terminals |
| Suhu Operasi | -40°C to +85°C |
| Timing Control | One external resistor and one external capacitor |
| Trigger Function | Separate trigger terminal |
| Reset Function | Separate reset terminal |
| Output Timing | Precisely controlled delay or oscillation |
| Terminal Finish | Tin Sn |
| Packaging | Tube |
| Jenis Pemasangan | Through-hole |
Panduan Konfigurasi Pin MC1455BP1G 8-pin pdip
Konfigurasi pin untuk MC1455BP1G (8-pin pdip pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk MC1455BP1G.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
MC1455BP1G patut untuk 6 aplikasis: Industrial Pulse and Delay Control, Astable Oscillator and Tone Generation, Legacy Through-Hole Timer Board, Indicator Flashing and Periodic Triggering, Test and Measurement Pulse Source, Educational Electronics Timing Circuit.
Industrial Pulse and Delay Control
The MC1455BP1G is suitable for industrial delay and pulse-control circuits because it combines a single 555 timer, a -40°C to +85°C operating range, and timing controlled by one external resistor and capacitor. In monostable operation, a trigger event starts one output pulse whose interval is established by the timing network. This arrangement is useful for actuator delay, relay sequencing, and one-shot control stages where a deterministic transition is required. The 8-pin PDIP package also permits socketed implementation where serviceability or replacement is important. Engineers should calculate the timing components for the full temperature range, verify trigger and reset levels against the datasheet, and include local supply decoupling to prevent supply disturbances from altering the output timing.
Disebarkan
Astable Oscillator and Tone Generation
The MC1455BP1G can generate a repetitive waveform in astable mode using an external resistor-capacitor network and the internal threshold and discharge functions. The onsemi datasheet identifies free-running frequency as externally controlled, making the part applicable to tone generators, clock-like signals, blinking indicators, and periodic test fixtures. Unlike a fixed-frequency oscillator, the timing values can be selected to match the required repetition rate. Because resistor and capacitor tolerance, temperature, and supply variation can affect the waveform, the timing components should be selected with the complete error budget in mind. Confirm the output duty cycle, discharge-device limits, and reset behavior against the manufacturer datasheet for each operating condition.
Disebarkan
Legacy Through-Hole Timer Board
The MC1455BP1G is a practical choice for maintaining or cloning legacy through-hole timer boards because it is offered in an 8-pin PDIP package and uses the established MC1455 single-timer architecture. The 555-family pin arrangement enables a direct comparison with existing NE555 and NA555 circuits, while the manufacturer datasheet provides the common timing, trigger, reset, and discharge framework. DIP construction simplifies socket use, probe access, and hand rework compared with a surface-mount timer. However, existing boards must still be checked for exact pin functions, voltage limits, output-current requirements, and any nonstandard wiring. Review the schematic and manufacturer data before assigning the alternative, and preserve adequate clearance around the package for soldering and inspection.
Disebarkan
Indicator Flashing and Periodic Triggering
A free-running MC1455BP1G can produce the periodic trigger required by a flashing indicator or repetitive actuator. The external timing network sets the oscillation rate, and the device output can drive a suitable interface stage rather than directly carrying an excessive lamp or relay load. This approach separates timing generation from the load-driving circuit, allowing the indicator flash rate to remain stable while transistor, MOSFET, or driver selection handles current. The -40°C to +85°C rated range is useful for industrial enclosures where temperature varies. Confirm output-current capability, timing tolerance, and reset behavior in the manufacturer datasheet, and include a current-limiting path appropriate for the indicator technology.
Disebarkan
Test and Measurement Pulse Source
The MC1455BP1G can serve as a simple adjustable pulse source in test and measurement equipment because the timing interval is set by one external resistor and one capacitor. Astable operation supports recurring pulses, while monostable operation produces a single interval after triggering, allowing the same architecture to address repetitive and one-shot test needs. The single-chip implementation reduces component count, and the 8-pin PDIP package is convenient for prototypes and educational fixtures. For laboratory-grade timing accuracy, evaluate capacitor and resistor tolerance, temperature drift, supply noise, and the measurement bandwidth of the output. Use the manufacturer datasheet to establish output rise and fall behavior and to avoid loading the timing node during investigation.
Disebarkan
Educational Electronics Timing Circuit
The MC1455BP1G is well suited to educational timer demonstrations because its 555 operation can be examined through astable oscillation, monostable delay, trigger, reset, and discharge behavior. Students can vary one timing resistor or capacitor to observe changes in repetition rate or pulse duration, while the 8-pin PDIP format provides clear physical access to every terminal. The 5 V and 15 V supply options also allow comparison between two common operating conditions. A breadboard or solderless training board is suitable for initial work, but the timing capacitor should have a known tolerance and the supply should be properly regulated. The manufacturer datasheet should accompany the exercise so that output states, trigger behavior, and reset requirements are interpreted correctly.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MC1455BP1G — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MC1455P1G | NE555N | NA555P | NE555P |
|---|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi |
| Timer Type | 555 Type | MC1455-family timer | 555 timer | Precision Timer | 555 timer |
| Timer Quantity | 1 timer | 1 timer | 1 timer | 1 timer | 1 timer |
Penyeberangsung Jelas
- Uses the onsemi MC1455 timing architecture rather than a generic cross-reference timer (vsNE555N)
- Combines monostable and astable operation with dedicated trigger and reset terminals (vsNA555P)
- Exact family ordering option for MC1455-based legacy designs (vsMC1455P1G)
Catatan Desain
Do not treat the trigger and reset terminals as unused merely because a circuit operates in one timing mode. Their inactive-state levels can affect whether the internal latch starts or remains reset. Before assembly, compare every numbered terminal on the PCB with the manufacturer pin-description diagram, especially on repaired legacy boards where the original device may have been substituted. Confirm that the replacement’s output and discharge functions occupy the same pins.
Place the supply bypass capacitor close to the power and ground pins, and route the return directly to the device ground reference. Keep the timing resistor and capacitor connection compact so the timing node is not exposed to unnecessary noise or capacitance. If the source supply is shared with switching circuitry, check that supply ripple does not corrupt the timing thresholds. The circuit is characterized for 5 V and 15 V supply conditions, so avoid assuming uninterrupted operation at arbitrary intermediate voltages.
Estimated: with a 15 V supply, a 5 V output, and a 100 mA output load, the regulator’s approximate dissipation is 1.0 W using P = (VIN − VOUT) × IOUT. The 8-pin PDIP exposes leads for heat conduction, but actual junction temperature depends on board copper, airflow, package construction, and the manufacturer thermal limits. For sustained higher current, calculate worst-case dissipation at maximum load and verify temperature rise against the applicable package data.
Maintain a conventional through-hole DIP-8 land pattern with adequate spacing for insertion, probe access, and hand soldering. For a socketed design, verify that the socket and the selected timer have compatible lead geometry. Keep sensitive timing nodes away from high-current switching paths and provide adequate copper return paths. The 8-pin PDIP format simplifies rework, but solder bridges between the closely spaced pins can alter timing or cause unintended trigger and reset states.
Maklumat Kesediaan
The component is a single timer IC; formal AEC-Q100 qualification is not established by the commercial MC1455BP1G listing. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or current compliance documentation.