onsemi

MC33201PG - 2.2MHz Rail-to-Rail Op Amp | onsemi | DIP-8

MPN: MC33201PG ✓ Aktif
1.8 V to 12 V Vdss 8-pin plastic DIP Package
MOQ: 1 |

MC33201PG Ringkasan

The onsemi MC33201PG is a single-amplifier, low-voltage rail-to-rail operational amplifier with a 2.2 MHz gain-bandwidth product, 1 V/µs slew rate, and a 1.8 V to 12 V supply range in an 8-pin plastic DIP package. Designed for general-purpose signal conditioning, the device combines rail-to-rail input and output operation with operation over a -40°C to +105°C temperature range.

An operational amplifier, or op amp, is an analog signal-conditioning semiconductor that amplifies the voltage difference between its inverting and non-inverting inputs. Within the broader hierarchy of analog semiconductors, the MC33201PG belongs to the voltage-feedback operational-amplifier family and provides a practical combination of low supply voltage, moderate bandwidth, and wide input and output swing. It is suitable for systems that need useful signal amplification without requiring the noise, offset, or power characteristics of a precision amplifier.

The rail-to-rail input stage can accept signals as much as 200 mV beyond the supply rails without phase reversal at the output. Rail-to-rail output operation allows the output voltage to approach both supply rails, with the output swinging within approximately 50 mV of each rail. These characteristics make the amplifier useful in low-voltage sensor interfaces, battery-powered instrumentation, and control systems where available signal range is limited by the supply voltage.

With a 2.2 MHz gain-bandwidth product and 1 V/µs slew rate, the MC33201PG is intended for general-purpose signal processing rather than high-speed video or precision measurement. Its single-amplifier configuration reduces board requirements where only one signal path is needed, while the 8-pin DIP format supports through-hole assembly, prototyping, educational platforms, and repair of legacy equipment.

Typical applications include low-voltage sensor buffering, portable measurement systems, audio preamplifier stages, motor and actuator control interfaces, and general feedback networks. The 1.8 V minimum supply supports modern low-voltage systems, while the 12 V maximum provides flexibility across industrial and consumer rails. The -40°C to +105°C operating range also supports industrial temperature requirements when other system parameters, such as offset and bias current, are acceptable.

PCB layout should keep feedback traces short, connect decoupling capacitors close to the supply pins, and route sensitive input nodes away from switching-current paths. Because a DIP package provides generous lead spacing, it is mechanically convenient for prototyping, but through-hole devices occupy more board area than comparable surface-mount packages. Engineers upgrading an existing MC33201PG design should preserve the established pin connections and account for the device's finite input and output swing limits.

This product page combines the manufacturer's electrical characteristics with engineering-oriented application guidance, pin information, comparison criteria, and practical layout considerations. It is intended to help designers evaluate the MC33201PG for low-voltage general-purpose amplification without confusing rail-to-rail capability with precision or high-speed performance.

Pilihan pengganti yang segera untuk MC33201PG — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

MC33201P

✅ Masuk Drop-In
📦 8-pin plastic DIP
Same MC33201 single-amplifier family and 8-pin DIP footprint; ordering-code and temperature-grade details must be confirmed, while the specified 1.8 V to 12 V supply range and 2.2 MHz bandwidth remain the closest listed match.

📋 Alternatif rujukan (tidak dalam katalog)

MC33201PG Penilaian maksimum & Ciri-ciri Elektrik

Amplifier Type Single rail-to-rail operational amplifier
Number of Amplifiers 1 amplifier
Supply Voltage Range 1.8 V to 12 V
Gain-Bandwidth Product 2.2 MHz
Slew Rate 1 V/µs
Input Common-Mode Range Rail-to-rail
Output Swing Within 50 mV of each supply rail
Over-Rail Input Tolerance Up to 200 mV beyond the supply rails without output phase reversal
Gambaran Suhu Operasi -40°C to +105°C
Kemasan 8-pin plastic DIP
Jenis Pemasangan Through-hole
Jenis Output Rail-to-rail
Status RoHS Compliant
Lead-Free Status Lead-free

Konfigurasi Pin MC33201PG

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
Pin 1 OFFSET NULL — Offset voltage adjustment input
Pin 2 INVERTING INPUT — Inverting input terminal
Pin 3 NON-INVERTING INPUT — Non-inverting input terminal
Pin 4 V- — Negative supply terminal
Pin 5 OFFSET NULL — Offset voltage adjustment input
Pin 6 OUTPUT — Amplifier output terminal
Pin 7 V+ — Positive supply terminal
Pin 8 NC — Not connected

Aplikasi Biasa

MC33201PG patut untuk 6 aplikasis: Low-Voltage Sensor Buffering, Battery-Powered Measurement Systems, Audio Preamplifier Stage, Industrial Control Signal Conditioning, Motor and Actuator Interfaces, Legacy Through-Hole Prototyping.

🧩

Low-Voltage Sensor Buffering

The MC33201PG fits sensor front ends that operate from a 1.8 V to 12 V supply and need more usable input range than a conventional fixed-range amplifier. Its rail-to-rail input stage can accept signals as much as 200 mV beyond the supply rails without output phase reversal, helping preserve small sensor outputs near the ends of the available voltage window. Place the device in a voltage follower or light-gain configuration, keep the sensor source impedance in mind, and confirm that its input bias current produces an acceptable sensor-loading error. The 2.2 MHz bandwidth is ample for many temperature, position, and environmental sensors, while the approximately 50 mV output headroom defines how close the output can approach either supply rail.

📱

Battery-Powered Measurement Systems

The MC33201PG is appropriate for compact, battery-powered measurement systems that require low-voltage operation and broad input range. Its minimum supply of 1.8 V supports energy-limited electronics, while rail-to-rail inputs reduce the need to bias sensor signals near mid-supply. The output can also move close to the positive and negative rails, leaving approximately 50 mV of headroom at either limit. This makes the amplifier useful in portable data loggers, handheld testers, and wearable sensor interfaces. Designers should verify the complete signal path at the lowest battery voltage, because sensor output, amplifier offset, and downstream converter input range can reduce usable resolution even when the amplifier itself remains functional.

🎧

Audio Preamplifier Stage

The MC33201PG can serve as a general-purpose audio preamplifier or line-stage amplifier in low-voltage equipment. Rail-to-rail output capability allows a single-supply implementation to use more of the available output range than a conventional amplifier with fixed common-mode limits. The 2.2 MHz gain-bandwidth product and 1 V/µs slew rate are suitable for modest audio-band signals and moderate gain stages. For microphonic or low-impedance sources, however, input bias current and noise must be checked before use. A practical design can bias the non-inverting input at mid-supply, reference the inverting network to the same point, and use the output stage to drive a higher-impedance audio or control path rather than a demanding loudspeaker directly.

🏭

Industrial Control Signal Conditioning

The MC33201PG is useful for conditioning low-level control signals in industrial equipment operating across a -40°C to +105°C range. Its 1.8 V to 12 V supply tolerance permits operation from low-voltage logic rails and nominal industrial supplies, while the single-amplifier configuration is economical when each channel requires one independent signal path. The device can implement non-inverting gain, inverting gain, differential-to-single-ended conversion, or active filtering. Engineers should account for common-mode voltage, output loading, and gain-bandwidth interaction. Because the MC33201PG is a general-purpose amplifier, applications demanding very accurate offset measurement, extremely low input bias current, or very high common-mode rejection should use a more specialized amplifier instead.

⚡

Motor and Actuator Interfaces

The MC33201PG can amplify position, current, or actuator-feedback signals in low-voltage motor-control subsystems. Its rail-to-rail inputs help retain small feedback voltages generated near a supply rail, and its 2.2 MHz bandwidth can support feedback networks above typical slow control-loop bandwidths. The device is more appropriate for conditioning feedback or command signals than for driving power MOSFETs, motor windings, or other high-current loads directly. A practical interface should place the amplifier close to the feedback source, use short feedback traces, and ensure the output remains within the amplifier's approximately 50 mV rail headroom. Additional filtering may be required when switching-node transitions are coupled into the sensed signal.

🔧

Legacy Through-Hole Prototyping

The MC33201PG is well suited to through-hole prototypes, educational instruments, maintenance boards, and small-lot analog experiments because its 8-pin DIP package is easy to install and inspect. The exposed lead spacing makes breadboard and through-hole prototype construction straightforward while retaining access to the offset-null pins for applications that need adjustment. Its 1.8 V to 12 V supply range allows quick evaluation from common laboratory rails, and the 2.2 MHz bandwidth is sufficient for many instructional and low-frequency signal-conditioning exercises. For new compact products, a surface-mount implementation may reduce board area, but migrating requires a footprint change and a careful review of pin correspondence, decoupling, stability, and thermal requirements.

Ringkasan Produk Disebarkan

MC33201P Same-family DIP alternative for sensor-interface designs Dipergunakan di: Low-Voltage Sensor Buffering, Battery-Powered Measurement Systems, Audio Preamplifier Stage, Industrial Control Signal Conditioning, Motor and Actuator Interfaces, Legacy Through-Hole Prototyping MC33201PG onsemi Dipergunakan di: Low-Voltage Sensor Buffering, Battery-Powered Measurement Systems, Industrial Control Signal Conditioning, Motor and Actuator Interfaces MC33201VP Same-family SOIC option where PCB redesign is permitted Dipergunakan di: Audio Preamplifier Stage, Legacy Through-Hole Prototyping
What is the operating voltage of the MC33201PG?
The MC33201PG operates from 1.8 V to 12 V. According to the onsemi manufacturer datasheet, this low supply range supports both modern battery-powered systems and conventional higher-voltage analog circuits. The single amplifier uses the same positive supply and ground references throughout its input, output, and power connections, allowing the device to be implemented with uncomplicated dual-rail or single-rail power arrangements appropriate to the application.
Is the MC33201PG a rail-to-rail operational amplifier?
Yes, the MC33201PG provides rail-to-rail operation at both the input and output. According to the onsemi manufacturer datasheet, its inputs can be driven as high as 200 mV beyond the supply rails without causing phase reversal at the output, while the output can swing within approximately 50 mV of each rail. These characteristics maximize usable signal range in low-voltage sensor and signal-conditioning circuits.
What is the gain-bandwidth product of the MC33201PG?
The MC33201PG has a 2.2 MHz gain-bandwidth product. The onsemi manufacturer datasheet identifies it as a single, general-purpose operational amplifier intended for low-voltage signal amplification. Bandwidth decreases as closed-loop gain increases, so 2.2 MHz is most useful at low gain, including voltage-follower, non-inverting amplifier, and light-feedback configurations rather than demanding high-gain or high-speed applications.
What is the slew rate of the MC33201PG?
The MC33201PG has a slew rate of 1 V/µs. According to the onsemi manufacturer datasheet, this is sufficient for general-purpose low-voltage signal processing and modest step-response requirements. Slew-rate demand rises with output amplitude and operating frequency, so designers should avoid interpreting the 2.2 MHz bandwidth as an indication that large-signal behavior will remain linear at the same rate.
What package does the MC33201PG use?
The MC33201PG uses an 8-pin plastic DIP package and is intended for through-hole assembly. DigiKey identifies the device as an 8-PDIP, and the onsemi manufacturer datasheet describes the MC33201 family's low-voltage rail-to-rail amplifier family. The DIP format is useful for prototyping and legacy-board maintenance but requires more PCB area and insertion clearance than a surface-mount equivalent.
Where can I download the MC33201PG datasheet PDF?
The MC33201PG datasheet PDF is available from the onsemi manufacturer page at https://www.onsemi.com/pdf/datasheet/mc33201-d.pdf. The document covers the MC33201, MC33202, MC33204, NCV33201, NCV33202, and NCV33204 family and is the primary reference for electrical characteristics, pin connections, typical application circuits, and ordering information.
What is the MC33201PG pinout?
The MC33201PG is an 8-pin DIP with offset null on pins 1 and 5, the inverting input on pin 2, the non-inverting input on pin 3, negative supply on pin 4, output on pin 6, positive supply on pin 7, and the unused NC pin on pin 8. Use the onsemi manufacturer datasheet pin-description table when making PCB connections or verifying a legacy design.
What can replace the MC33201PG in an existing circuit?
The MC33201P is the closest listed drop-in candidate because it uses the same 8-pin DIP footprint and belongs to the same MC33201 family. According to the onsemi manufacturer datasheet family information, the core single-amplifier function remains the same, while the exact ordering-temperature and marking details must be checked against the original purchase specification. Cross-brand replacements require verification of every pin and electrical parameter.
Is MC33201PG suitable for low-voltage sensor interfaces?
Yes, the MC33201PG is suitable for many low-voltage sensor interfaces. Its 1.8 V to 12 V supply range and rail-to-rail inputs allow it to work near the limits of a restricted supply, while the approximately 50 mV output headroom helps maximize output range. Offset, bias current, noise, and stability should still be checked against the sensor's output impedance and required measurement accuracy.
MC33201PG vs MC33201P: which part should I select?
Choose the MC33201PG when the required grade and marking match the original device; choose MC33201P when that ordering code satisfies the production specification and remains active for the intended program. Both are associated with the same onsemi MC33201 family and 8-pin DIP implementation. Compare the ordering table and temperature-grade markings before treating either part as a substitute.
When should I choose the MC33201PG over a precision amplifier?
Choose the MC33201PG for general-purpose amplification where moderate offset, noise, and drift are acceptable and low supply voltage, rail-to-rail operation, and a 2.2 MHz bandwidth are more important than precision. A precision amplifier is preferable when measurement accuracy, very low input bias current, low offset voltage, or minimal drift drives the system requirement. The onsemi manufacturer datasheet should guide the final comparison.
Where can I buy MC33201PG and check its lead time?
Use the Request a Quote form on this page to request MC33201PG availability, current lead time, and order quantities. The form allows the request to be matched to the exact 8-pin DIP ordering code without relying on changing distributor inventory messages. Include target quantity, permitted substitutions, and delivery requirements when submitting the commercial request.
What is the price of the MC33201PG?
Use the Request a Quote form on this page for the current MC33201PG unit price and quantity breaks. Commercial pricing depends on order quantity, packaging, availability, and purchasing terms, so it is intentionally presented through the quotation workflow rather than as a static value. The request should identify MC33201PG, the required quantity, and any acceptable manufacturer-authorized alternatives.
Is the MC33201PG currently in stock?
Stock status for MC33201PG should be confirmed through the Request a Quote form on this page. Because inventory and lead time can change independently of a device's lifecycle status, the quotation workflow provides a current answer for the exact package and ordering code. State your required quantity and production schedule so the response can reflect meaningful availability rather than a generic catalog quantity.
What are the key specifications of MC33201PG that engineers should know?
The principal MC33201PG specifications are 1.8 V to 12 V operation, 2.2 MHz gain-bandwidth product, 1 V/µs slew rate, rail-to-rail input and output behavior, and a -40°C to +105°C operating range. According to the onsemi manufacturer datasheet, the input stage tolerates signals 200 mV beyond the rails without phase reversal, and the output swings within approximately 50 mV of each rail.

Data referensi kejuruteraan untuk MC33201PG — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the MC33201PG for a general-purpose, low-voltage through-hole design that benefits from rail-to-rail input and output behavior. Its 1.8 V to 12 V supply range is especially useful for battery-powered sensing and compact control systems, while 2.2 MHz bandwidth and 1 V/µs slew rate are adequate for modest-speed signal paths. Select a precision amplifier instead when offset voltage, bias current, drift, noise, or common-mode rejection are the dominant requirements. MC33201P is the closest listed same-family through-hole alternative when its ordering code and temperature grade satisfy the production requirements. MC33201VP may suit the same electrical function in a redesigned surface-mount PCB, but it is not a drop-in footprint replacement for the DIP package. Before any substitution, confirm pin assignment, supply limits, offset behavior, input bias current, stability, and the required operating-temperature grade.

Perbandingan dengan Gantian

Parametr Produk Ini MC33201P
Brand onsemi onsemi
Package 8-pin plastic DIP 8-pin plastic DIP
Amplifier Count 1 amplifier 1 amplifier
Mounting Type Through-hole Through-hole

Penyeberangsung Jelas

  • Broad usable input range from a low-power supply (vsMC33201P)
  • Output range closely approaches both supply rails (vsMC33201P)
  • Through-hole package supports simple PCB integration (vsMC33201VP)

Catatan Desain

Place the positive and negative supply bypass capacitors close to pins 7 and 4, respectively, and keep the associated ground-return paths short. Connect the inverting-input feedback components directly to pin 2 and minimize copper area around the non-inverting input at pin 3. For stable operation with the DIP footprint, use short feedback traces and avoid routing them beneath or alongside high-current switching paths.

Do not treat rail-to-rail input capability as unlimited common-mode range. The manufacturer datasheet specifies that inputs may be driven as much as 200 mV beyond the rails without phase reversal, but sustained operation outside the specified supply conditions can damage the amplifier. Likewise, the output does not reach the rails exactly: allow approximately 50 mV of headroom and verify the final output range against the load and supply tolerances.

Use the 2.2 MHz gain-bandwidth product to select a practical closed-loop gain. Higher noise gain reduces closed-loop bandwidth, while large output steps can expose the 1 V/µs slew-rate limit. For sensor inputs with substantial source impedance, compare source impedance with the amplifier's bias-current behavior and add an appropriate bias resistor or buffer if loading would degrade accuracy.

Pins 1 and 5 are offset-null terminals, not additional signal inputs. Leave them open when factory adjustment is acceptable, and avoid connecting a capacitor or external trim network unless the circuit is specifically designed for offset adjustment. Verify the datasheet ordering information before substituting MC33201P because ordering suffixes can encode temperature grade, package, or production status.

Maklumat Kesediaan

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Yes
Bosong halogen
Unknown
Mineral konflik
Unknown

The MC33201PG is described as RoHS-compliant and lead-free. No specific AEC-Q100 qualification, REACH status, halogen-free declaration, or conflict-minerals statement is included for the exact ordering code.

Data disahkan pada: 2026-11-16 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

MC33201PG datasheet MC33201PG datasheet pdf MC33201PG pinout MC33201PG specifications MC33201PG price MC33201PG stock onsemi MC33201PG MC33201PG equivalent MC33201PG replacement MC33201P vs MC33201PG MC33201PG 2.2MHz op amp MC33201PG rail to rail MC33201PG DIP-8 amplifier MC33201PG sensor interface MC33201PG application circuit

Komponen dan Tanda berkaitan

onsemi MC33201PG MC33201P MC33201VP MC33201 MC33202 MC33204 NCV33201 operational amplifier op amp voltage-feedback amplifier rail-to-rail input rail-to-rail output analog signal conditioning gain-bandwidth product slew rate common-mode voltage offset null 8-pin plastic DIP DIP package through-hole assembly surface mount low-voltage operation battery-powered instrumentation industrial control
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ