MC33201PG - 2.2MHz Rail-to-Rail Op Amp | onsemi | DIP-8
MPN: MC33201PG ✓ NakahandaMC33201PG Ulas
An operational amplifier, or op amp, is an analog signal-conditioning semiconductor that amplifies the voltage difference between its inverting and non-inverting inputs. Within the broader hierarchy of analog semiconductors, the MC33201PG belongs to the voltage-feedback operational-amplifier family and provides a practical combination of low supply voltage, moderate bandwidth, and wide input and output swing. It is suitable for systems that need useful signal amplification without requiring the noise, offset, or power characteristics of a precision amplifier.
The rail-to-rail input stage can accept signals as much as 200 mV beyond the supply rails without phase reversal at the output. Rail-to-rail output operation allows the output voltage to approach both supply rails, with the output swinging within approximately 50 mV of each rail. These characteristics make the amplifier useful in low-voltage sensor interfaces, battery-powered instrumentation, and control systems where available signal range is limited by the supply voltage.
With a 2.2 MHz gain-bandwidth product and 1 V/µs slew rate, the MC33201PG is intended for general-purpose signal processing rather than high-speed video or precision measurement. Its single-amplifier configuration reduces board requirements where only one signal path is needed, while the 8-pin DIP format supports through-hole assembly, prototyping, educational platforms, and repair of legacy equipment.
Typical applications include low-voltage sensor buffering, portable measurement systems, audio preamplifier stages, motor and actuator control interfaces, and general feedback networks. The 1.8 V minimum supply supports modern low-voltage systems, while the 12 V maximum provides flexibility across industrial and consumer rails. The -40°C to +105°C operating range also supports industrial temperature requirements when other system parameters, such as offset and bias current, are acceptable.
PCB layout should keep feedback traces short, connect decoupling capacitors close to the supply pins, and route sensitive input nodes away from switching-current paths. Because a DIP package provides generous lead spacing, it is mechanically convenient for prototyping, but through-hole devices occupy more board area than comparable surface-mount packages. Engineers upgrading an existing MC33201PG design should preserve the established pin connections and account for the device's finite input and output swing limits.
This product page combines the manufacturer's electrical characteristics with engineering-oriented application guidance, pin information, comparison criteria, and practical layout considerations. It is intended to help designers evaluate the MC33201PG for low-voltage general-purpose amplification without confusing rail-to-rail capability with precision or high-speed performance.
Mga alternatibo na pwedeng ilagay na MC33201PG — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
MC33201P
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
MC33201PG Mga Pinakamataas na Rating at Electrical Characteristics
| Amplifier Type | Single rail-to-rail operational amplifier |
| Number of Amplifiers | 1 amplifier |
| Supply Voltage Range | 1.8 V to 12 V |
| Gain-Bandwidth Product | 2.2 MHz |
| Slew Rate | 1 V/µs |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Within 50 mV of each supply rail |
| Over-Rail Input Tolerance | Up to 200 mV beyond the supply rails without output phase reversal |
| Hanay ng Temperature na Operasyon | -40°C to +105°C |
| Packhaging | 8-pin plastic DIP |
| Uri ng Pagpapasok | Through-hole |
| Type ng Output | Rail-to-rail |
| Tindminan RoHS | Compliant |
| Lead-Free Status | Lead-free |
Pin Configuration ng MC33201PG
| Pin 1 | OFFSET NULL — Offset voltage adjustment input |
| Pin 2 | INVERTING INPUT — Inverting input terminal |
| Pin 3 | NON-INVERTING INPUT — Non-inverting input terminal |
| Pin 4 | V- — Negative supply terminal |
| Pin 5 | OFFSET NULL — Offset voltage adjustment input |
| Pin 6 | OUTPUT — Amplifier output terminal |
| Pin 7 | V+ — Positive supply terminal |
| Pin 8 | NC — Not connected |
Tipikal na mga Gamit
MC33201PG ay nararapat para sa 6 aplikasyons: Low-Voltage Sensor Buffering, Battery-Powered Measurement Systems, Audio Preamplifier Stage, Industrial Control Signal Conditioning, Motor and Actuator Interfaces, Legacy Through-Hole Prototyping.
Low-Voltage Sensor Buffering
The MC33201PG fits sensor front ends that operate from a 1.8 V to 12 V supply and need more usable input range than a conventional fixed-range amplifier. Its rail-to-rail input stage can accept signals as much as 200 mV beyond the supply rails without output phase reversal, helping preserve small sensor outputs near the ends of the available voltage window. Place the device in a voltage follower or light-gain configuration, keep the sensor source impedance in mind, and confirm that its input bias current produces an acceptable sensor-loading error. The 2.2 MHz bandwidth is ample for many temperature, position, and environmental sensors, while the approximately 50 mV output headroom defines how close the output can approach either supply rail.
Inirekomenda
Battery-Powered Measurement Systems
The MC33201PG is appropriate for compact, battery-powered measurement systems that require low-voltage operation and broad input range. Its minimum supply of 1.8 V supports energy-limited electronics, while rail-to-rail inputs reduce the need to bias sensor signals near mid-supply. The output can also move close to the positive and negative rails, leaving approximately 50 mV of headroom at either limit. This makes the amplifier useful in portable data loggers, handheld testers, and wearable sensor interfaces. Designers should verify the complete signal path at the lowest battery voltage, because sensor output, amplifier offset, and downstream converter input range can reduce usable resolution even when the amplifier itself remains functional.
Inirekomenda
Audio Preamplifier Stage
The MC33201PG can serve as a general-purpose audio preamplifier or line-stage amplifier in low-voltage equipment. Rail-to-rail output capability allows a single-supply implementation to use more of the available output range than a conventional amplifier with fixed common-mode limits. The 2.2 MHz gain-bandwidth product and 1 V/µs slew rate are suitable for modest audio-band signals and moderate gain stages. For microphonic or low-impedance sources, however, input bias current and noise must be checked before use. A practical design can bias the non-inverting input at mid-supply, reference the inverting network to the same point, and use the output stage to drive a higher-impedance audio or control path rather than a demanding loudspeaker directly.
Inirekomenda
Industrial Control Signal Conditioning
The MC33201PG is useful for conditioning low-level control signals in industrial equipment operating across a -40°C to +105°C range. Its 1.8 V to 12 V supply tolerance permits operation from low-voltage logic rails and nominal industrial supplies, while the single-amplifier configuration is economical when each channel requires one independent signal path. The device can implement non-inverting gain, inverting gain, differential-to-single-ended conversion, or active filtering. Engineers should account for common-mode voltage, output loading, and gain-bandwidth interaction. Because the MC33201PG is a general-purpose amplifier, applications demanding very accurate offset measurement, extremely low input bias current, or very high common-mode rejection should use a more specialized amplifier instead.
Inirekomenda
Motor and Actuator Interfaces
The MC33201PG can amplify position, current, or actuator-feedback signals in low-voltage motor-control subsystems. Its rail-to-rail inputs help retain small feedback voltages generated near a supply rail, and its 2.2 MHz bandwidth can support feedback networks above typical slow control-loop bandwidths. The device is more appropriate for conditioning feedback or command signals than for driving power MOSFETs, motor windings, or other high-current loads directly. A practical interface should place the amplifier close to the feedback source, use short feedback traces, and ensure the output remains within the amplifier's approximately 50 mV rail headroom. Additional filtering may be required when switching-node transitions are coupled into the sensed signal.
Inirekomenda
Legacy Through-Hole Prototyping
The MC33201PG is well suited to through-hole prototypes, educational instruments, maintenance boards, and small-lot analog experiments because its 8-pin DIP package is easy to install and inspect. The exposed lead spacing makes breadboard and through-hole prototype construction straightforward while retaining access to the offset-null pins for applications that need adjustment. Its 1.8 V to 12 V supply range allows quick evaluation from common laboratory rails, and the 2.2 MHz bandwidth is sufficient for many instructional and low-frequency signal-conditioning exercises. For new compact products, a surface-mount implementation may reduce board area, but migrating requires a footprint change and a careful review of pin correspondence, decoupling, stability, and thermal requirements.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MC33201PG — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | MC33201P |
|---|---|---|
| Brand | onsemi | onsemi |
| Package | 8-pin plastic DIP | 8-pin plastic DIP |
| Amplifier Count | 1 amplifier | 1 amplifier |
| Mounting Type | Through-hole | Through-hole |
Pangunahing mga Pagkakaiba
- Broad usable input range from a low-power supply (kumpara saMC33201P)
- Output range closely approaches both supply rails (kumpara saMC33201P)
- Through-hole package supports simple PCB integration (kumpara saMC33201VP)
Talaan ng Disenyo
Place the positive and negative supply bypass capacitors close to pins 7 and 4, respectively, and keep the associated ground-return paths short. Connect the inverting-input feedback components directly to pin 2 and minimize copper area around the non-inverting input at pin 3. For stable operation with the DIP footprint, use short feedback traces and avoid routing them beneath or alongside high-current switching paths.
Do not treat rail-to-rail input capability as unlimited common-mode range. The manufacturer datasheet specifies that inputs may be driven as much as 200 mV beyond the rails without phase reversal, but sustained operation outside the specified supply conditions can damage the amplifier. Likewise, the output does not reach the rails exactly: allow approximately 50 mV of headroom and verify the final output range against the load and supply tolerances.
Use the 2.2 MHz gain-bandwidth product to select a practical closed-loop gain. Higher noise gain reduces closed-loop bandwidth, while large output steps can expose the 1 V/µs slew-rate limit. For sensor inputs with substantial source impedance, compare source impedance with the amplifier's bias-current behavior and add an appropriate bias resistor or buffer if loading would degrade accuracy.
Pins 1 and 5 are offset-null terminals, not additional signal inputs. Leave them open when factory adjustment is acceptable, and avoid connecting a capacitor or external trim network unless the circuit is specifically designed for offset adjustment. Verify the datasheet ordering information before substituting MC33201P because ordering suffixes can encode temperature grade, package, or production status.
Impormasyon ng Pagsunod sa Kautusan
The MC33201PG is described as RoHS-compliant and lead-free. No specific AEC-Q100 qualification, REACH status, halogen-free declaration, or conflict-minerals statement is included for the exact ordering code.