NXP Semiconductors

MC33662JEF - LIN Half Bus Transceiver | NXP | Automotive

MPN: MC33662JEF ✓ Aktif
13.5 V Vdss SOIC-8 Package
MOQ: 1 |

MC33662JEF Ringkasan

NXP Semiconductors MC33662JEF is an automotive LIN bus physical-layer transceiver with one transmitter and one receiver, supplied in an 8-pin SOIC package. The device is designed for a nominal 13.5 V supply and operates across a temperature range from -40 °C to +125 °C. Its LIN physical-layer implementation supports ISO 17987, LIN 2.x, and SAE J2602-2.

A LIN transceiver is an interface IC that connects a microcontroller or logic device to a Local Interconnect Network bus. LIN is a low-cost, single-wire automotive network used for distributed body electronics such as door modules, seat controls, lighting, climate controls, and small sensor or actuator subsystems. The MC33662JEF sits between the host controller and the physical LIN network, translating logic-level signals into the bus waveform and receiving bus data for the controller.

The principal identified features are a single LIN transmitter and receiver, 13.5 V nominal supply, operation from -40 °C to +125 °C, and an 8-terminal SOIC package. Its extended temperature range makes it suitable for demanding automotive environments where consumer-grade interface circuits may not provide sufficient operating margin. The SOIC package also supports conventional leaded automotive PCB assembly processes.

Technically, the MC33662JEF implements the LIN physical layer required to communicate with LIN nodes over the vehicle's low-speed serial network. Compatibility with ISO 17987, LIN 2.x, and SAE J2602-2 identifies the principal physical-layer specifications associated with the device. Designers should treat those standards as system-level requirements and confirm the complete network implementation against the NXP datasheet before releasing a vehicle program.

Typical applications include automotive body-control modules, door and seat control units, climate-control panels, lighting controllers, ambient sensors, powered seat modules, and other LIN-connected body electronics. A microcontroller can use the transceiver's receive output and transmit input while external bus protection, pull-up, filtering, and power-distribution components complete the LIN node.

When laying out a LIN node, place the transceiver close to the connector and route the LIN bus as a short, protected branch away from sensitive sensor signals. Validate the bus waveform, dominant and recessive states, wake-up behavior, and fault recovery at the vehicle power extremes. Exact pin assignments and recommended external components should be implemented from the manufacturer datasheet.

This page combines package, interface, environmental, and standards information with practical application guidance and an honest review of drop-in replacement availability. It also identifies where detailed electrical limits, pin descriptions, and lifecycle documentation must be confirmed before hardware release.

Pilihan pengganti yang segera untuk MC33662JEF — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

MC33662JEFR2

✅ Masuk Drop-In
📦 SOIC-8
Identical 1-transmitter/1-receiver LIN interface and 8-pin SOIC construction; ordering suffix and packing presentation differ by 0% in the identified electrical function.

📋 Alternatif rujukan (tidak dalam katalog)

MC33662JEF Spesifikasi

Product Type LIN Bus Physical-Layer Transceiver
Transmitter and Receiver Count 1 transmitter and 1 receiver
Bus Type LINbus
Nominal Supply Voltage 13.5 V
Minimum Operating Temperature -40 °C
Maximum Operating Temperature 125 °C
Total Pin Count 8 pins
Package Type SOIC-8
Package Code R-PDSO-G8
Package Width 3.9 mm
Package Length 4.9 mm
Terminal Form Gull wing
Package Shape Rectangular
Application Classification Automotive
ISO 17987 Support Supported
LIN 2.x Support Supported
SAE J2602-2 Support Supported
Jenis Pemasangan Surface mount

Panduan Konfigurasi Pin MC33662JEF rectangular

Konfigurasi pin untuk MC33662JEF (rectangular pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai rectangular untuk MC33662JEF

Tiada data garisan pin yang diperoleh untuk MC33662JEF.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

MC33662JEF patut untuk 6 aplikasis: Automotive Body Control Module, Door and Seat Control Module, Automotive Climate Control Panel, Lighting Control Network, Automotive Sensor Node, Vehicle Actuator Controller.

🚗

Automotive Body Control Module

The MC33662JEF fits an LIN-connected body-control module that coordinates distributed door, lighting, climate, or seat functions. Its one-transmitter/one-receiver architecture connects a host microcontroller to a LIN subnet while the 8-pin SOIC package simplifies conventional automotive PCB assembly. The -40 °C to +125 °C operating range provides environmental margin for cabin and body electronics. The LIN bus still requires the appropriate external protection and network components defined by the manufacturer application circuit, and system validation should cover dominant and recessive waveforms, wake-up behavior, bus faults, and power-transient conditions.

🚗

Door and Seat Control Module

The MC33662JEF is appropriate for door and seat control units that use LIN sub-buses to reduce wiring between switches, motors, sensors, and a local controller. The device provides one LIN transmitter and one receiver in an 8-pin SOIC package, giving the designer a compact interface to the host MCU. Its operation to 125 °C is relevant to parked-vehicle environments, although internal module temperatures must be checked against the device rating. Place the transceiver near the harness connector, route the LIN conductor away from sensitive analog signals, and verify startup, sleep, wake-up, and recovery behavior over the complete vehicle supply range.

🏭

Automotive Climate Control Panel

A climate-control panel can use the MC33662JEF to communicate with distributed temperature controls, fan commands, button modules, or actuator nodes over LIN. The 1/1 transceiver arrangement supports bidirectional bus communication through separate transmit and receive functions, while the 8-pin SOIC footprint keeps the physical interface compact. Its stated ISO 17987, LIN 2.x, and SAE J2602-2 support provides a clear physical-layer basis for network design. The implementation should still validate timing, bus loading, fault reporting, and behavior when a remote node drives the bus during startup or shutdown.

💡

Lighting Control Network

The MC33662JEF can serve as the LIN interface in an automotive lighting control node connected to exterior lamps, switches, or light sensors. The nominal 13.5 V operating point aligns with a conventional vehicle low-voltage supply, while the -40 °C to +125 °C rating supports the broad environmental conditions encountered by body-mounted electronics. The SOIC-8 package is practical for leaded assembly and rework. Designers should confirm the transceiver's detailed supply thresholds and LIN timing from the NXP datasheet, then validate the finished node against the vehicle's wake-up, load-dump, and bus-fault requirements.

🧩

Automotive Sensor Node

The MC33662JEF is suitable for a LIN-connected sensor node that reports switch, temperature, or occupancy-related information to a central controller. A LIN subnetwork is useful when a smart sensor needs power, communication, and diagnostics over a compact harness. The MC33662JEF supplies the physical-layer transceiver required between the smart-sensor logic and the bus, with operation specified from -40 °C to +125 °C. Apply the manufacturer's recommended bus protection and decoupling arrangement, maintain a controlled return path, and test the node with realistic bus capacitance and neighboring LIN devices to confirm communication margin.

⚡

Vehicle Actuator Controller

The MC33662JEF can interface a low-bandwidth LIN actuator controller used for pumps, small motors, valves, or powered access mechanisms. Its single transmitter and receiver provide the basic physical-layer functions required by a LIN master or slave node, and the compact 8-pin SOIC package leaves board area for local power and driver circuitry. The extended automotive temperature range supports use across multiple vehicle compartments, but thermal placement still requires verification at the highest local ambient temperature. Protect the transceiver from wiring transients, follow the datasheet's external-component recommendations, and validate communication through power cycling and disconnected-node fault cases.

Ringkasan Produk Disebarkan

MC33662JEF NXP Semiconductors Dipergunakan di: Automotive Body Control Module, Door and Seat Control Module, Automotive Climate Control Panel, Lighting Control Network, Automotive Sensor Node, Vehicle Actuator Controller MC33662JEFR2 Same-family reel-form ordering option Dipergunakan di: Automotive Body Control Module, Door and Seat Control Module, Automotive Climate Control Panel, Lighting Control Network, Automotive Sensor Node, Vehicle Actuator Controller
What is the MC33662JEF?
The MC33662JEF is an NXP Semiconductors LIN bus physical-layer transceiver containing one transmitter and one receiver in an 8-pin SOIC package. According to the NXP datasheet information, it operates from a nominal 13.5 V supply over -40 °C to +125 °C and supports ISO 17987, LIN 2.x, and SAE J2602-2 physical-layer requirements.
What is the operating voltage of MC33662JEF?
The MC33662JEF uses a nominal supply voltage of 13.5 V, consistent with an automotive low-voltage electrical system. The NXP datasheet information identifies that nominal value, while the precise minimum and maximum supply limits must be taken from the manufacturer's recommended operating conditions before final circuit design.
What is the operating temperature range of MC33662JEF?
The MC33662JEF operates from -40 °C to +125 °C. According to the MC33662JEF technical description, this automotive temperature range supports use in body electronics exposed to temperature variations beyond the normal consumer-commercial range.
What package does MC33662JEF use?
The MC33662JEF is supplied in an 8-pin SOIC package identified as R-PDSO-G8. The package dimensions listed for the device are approximately 3.9 mm wide by 4.9 mm long, with gull-wing leads and a rectangular package shape.
Where can I download the MC33662JEF datasheet PDF?
The MC33662JEF datasheet is available through the NXP MC33662JEF datasheet listing at Datasheets.com, and an additional datasheet download page is hosted by AllDataSheet. Use the manufacturer datasheet as the controlling document for pinout, electrical limits, application circuit, and qualification information.
Where can I find the MC33662JEF pinout?
The MC33662JEF pinout should be taken from the manufacturer datasheet's R-PDSO-G8 pin-description table because the complete numbered pin list is not reproduced in the available product summary. Assign PCB tracks only after checking the LIN, supply, ground, transmit, receive, and enable functions against that table.
Is the MC33662JEF suitable for automotive LIN bus applications?
The MC33662JEF is designed for automotive LIN physical-layer applications and has a -40 °C to +125 °C operating range. Its support for ISO 17987, LIN 2.x, and SAE J2602-2 makes it appropriate for LIN nodes in body-control, lighting, climate, seat, and sensor subsystems, subject to application-level validation.
MC33662JEF vs MC33662JEFR2 - which is the better replacement?
The MC33662JEFR2 is the reel-form ordering variant associated with the same MC33662 family and 8-pin SOIC interface construction. The functional selection should be based on the manufacturer ordering table, temperature grade, and packing code; confirm the exact suffix and reel quantity before substituting one orderable part number for another.
What can replace the MC33662JEF?
A valid MC33662JEF replacement must match the 8-pin SOIC footprint, LIN physical-layer function, supply requirements, and automotive temperature range. No independently verified cross-brand drop-in substitute was identified for this exact MPN, so use the NXP cross-reference and product-selector resources to validate any proposed alternative rather than treating a generic LIN transceiver as automatically interchangeable.
Can an MC33662JEF replace another LIN transceiver?
The MC33662JEF can replace another LIN transceiver only when its complete pinout, electrical limits, bus behavior, and package dimensions match the incumbent device. Confirm those details in the manufacturer datasheets, and perform bus compatibility and fault-recovery testing before approving the substitution.
When should I choose the MC33662JEF over another LIN transceiver?
Choose the MC33662JEF when the design requires an NXP 8-pin SOIC LIN physical layer with a nominal 13.5 V supply, operation across -40 °C to +125 °C, and stated support for ISO 17987, LIN 2.x, and SAE J2602-2. Select another part only when its pinout and electrical behavior are demonstrably equivalent.
Is the MC33662JEF still in stock and what is its lead time?
Current stock and lead time can change without notice, so use the Request a Quote form on this page to confirm availability, minimum order quantity, and delivery timing for MC33662JEF. The form keeps the request associated with the exact MPN and its automotive 8-pin SOIC ordering configuration.
Where should I buy the MC33662JEF?
Use the Request a Quote form on this page to request MC33662JEF pricing, stock, and lead time. Provide the required reel or tube packing option and production quantity so the exact automotive ordering configuration can be confirmed without relying on a generic or mismatched part listing.
What are the key specifications of MC33662JEF that engineers should know?
The MC33662JEF combines one LIN transmitter and one receiver, a nominal 13.5 V supply, a -40 °C to +125 °C operating range, and an 8-pin R-PDSO-G8 SOIC package. Its stated physical-layer support includes ISO 17987, LIN 2.x, and SAE J2602-2, making the device suited to automotive body electronics.
Is there an automotive-grade LIN transceiver equivalent to MC33662JEF?
The MC33662JEF is itself identified for automotive applications, but a cross-brand equivalent must still demonstrate the same SOIC-8 pinout, supply range, LIN waveform, temperature grade, and fault behavior. No verified cross-brand drop-in candidate was established, so an equivalent should be qualified through manufacturer cross-reference data and application testing.

Data referensi kejuruteraan untuk MC33662JEF — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Select MC33662JEF for an automotive LIN node that requires an NXP 8-pin SOIC physical-layer transceiver, a nominal 13.5 V supply, and operation across -40 °C to +125 °C. MC33662JEFR2 is the closest listed same-family option because it uses the same SOIC-8 construction and is identified as a 1/1 LIN transceiver; choose it when its manufacturer ordering code and packing format better match production procurement. No verified cross-brand drop-in replacement was established, so a different manufacturer's LIN transceiver should be considered only after its pinout, electrical limits, wake-up behavior, protection requirements, and fault recovery are shown to be equivalent. For conventional consumer or industrial equipment outside the automotive environment, a non-automotive LIN transceiver may offer a better operating-temperature or qualification fit. In all cases, validate the complete LIN node for waveform timing, network capacitance, power transients, sleep and wake behavior, and fault recovery.

Perbandingan dengan Gantian

Parametr Produk Ini MC33662JEFR2
Package 8-pin SOIC (R-PDSO-G8) 8-pin SOIC (R-PDSO-G8)
Brand NXP Semiconductors NXP Semiconductors
Transmitter and Receiver Count 1 transmitter and 1 receiver 1 transmitter and 1 receiver
Nominal Supply Voltage 13.5 V 13.5 V
Minimum Operating Temperature -40 °C -40 °C
Maximum Operating Temperature 125 °C 125 °C
Interface Standard ISO 17987, LIN 2.x, SAE J2602-2 ISO 17987, LIN 2.x, SAE J2602-2
Total Pin Count 8 pins 8 pins
Package Width 3.9 mm 3.9 mm
Package Length 4.9 mm 4.9 mm

Penyeberangsung Jelas

  • Automotive temperature coverage (vsMC33662JEFR2)
  • Compact physical interface (vsMC33662JEFR2)
  • Physical-layer compatibility (vsMC33662JEFR2)

Catatan Desain

Place the MC33662JEF and its required bypass components near the vehicle harness connector and LIN route. Keep the LIN conductor away from high-current switching nodes, crystal clocks, and sensitive sensor inputs, and provide a direct, low-impedance return path. Confirm the final track geometry, protection placement, and ground reference against the manufacturer application circuit before PCB release.

Design the module around the device's 13.5 V nominal automotive supply while protecting the MC33662JEF from wiring transients and load-dump events. Follow the NXP datasheet for supply decoupling, external protection, and operating limits, and verify startup, shutdown, sleep, and wake-up behavior with the complete vehicle power profile rather than only a laboratory supply.

Do not treat every 8-pin LIN transceiver as a pin-compatible substitute. Check the complete R-PDSO-G8 pin assignment, LIN TX/RX logic, enable behavior, supply thresholds, timing, and fault recovery for both the installed and proposed device. After substitution, test dominant and recessive waveforms, bus loading, disconnected nodes, stuck-at faults, and operation across the full vehicle temperature range.

Use the LIN network's specified rise and fall times, bus capacitance, termination strategy, and waveform margins as the acceptance criteria for signal integrity. Keep external protection capacitance from excessively slowing transitions, use a controlled reference plane, and inspect the bus with an oscilloscope at the connector during EMC testing. The -40 °C to +125 °C device rating does not by itself guarantee timing margin across the complete network.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The device is identified for automotive use, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified. Confirm these attributes with the manufacturer product documentation before qualification.

Data disahkan pada: 2026-11-16 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

MC33662JEF datasheet MC33662JEF pinout MC33662JEF datasheet pdf MC33662JEF equivalent MC33662JEF replacement MC33662JEF cross reference MC33662JEF vs MC33662JEFR2 MC33662JEF price MC33662JEF stock NXP MC33662JEF MC33662JEF SOIC-8 footprint MC33662JEF LIN 2.x transceiver

Komponen dan Tanda berkaitan

NXP Semiconductors MC33662JEF MC33662JEFR2 LIN bus LIN physical layer transceiver interface IC semiconductor Local Interconnect Network ISO 17987 LIN 2.x SAE J2602-2 SOIC-8 R-PDSO-G8 surface-mount package automotive electronics body control module vehicle sensor node vehicle actuator controller 13.5 V nominal supply LIN transmitter LIN receiver wake-up behavior bus protection RoHS REACH AEC-Q100
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ