MC33662JEF - LIN Half Bus Transceiver | NXP | Automotive
MPN: MC33662JEF ✓ Hoạt độngMC33662JEF Tóm tắt
A LIN transceiver is an interface IC that connects a microcontroller or logic device to a Local Interconnect Network bus. LIN is a low-cost, single-wire automotive network used for distributed body electronics such as door modules, seat controls, lighting, climate controls, and small sensor or actuator subsystems. The MC33662JEF sits between the host controller and the physical LIN network, translating logic-level signals into the bus waveform and receiving bus data for the controller.
The principal identified features are a single LIN transmitter and receiver, 13.5 V nominal supply, operation from -40 °C to +125 °C, and an 8-terminal SOIC package. Its extended temperature range makes it suitable for demanding automotive environments where consumer-grade interface circuits may not provide sufficient operating margin. The SOIC package also supports conventional leaded automotive PCB assembly processes.
Technically, the MC33662JEF implements the LIN physical layer required to communicate with LIN nodes over the vehicle's low-speed serial network. Compatibility with ISO 17987, LIN 2.x, and SAE J2602-2 identifies the principal physical-layer specifications associated with the device. Designers should treat those standards as system-level requirements and confirm the complete network implementation against the NXP datasheet before releasing a vehicle program.
Typical applications include automotive body-control modules, door and seat control units, climate-control panels, lighting controllers, ambient sensors, powered seat modules, and other LIN-connected body electronics. A microcontroller can use the transceiver's receive output and transmit input while external bus protection, pull-up, filtering, and power-distribution components complete the LIN node.
When laying out a LIN node, place the transceiver close to the connector and route the LIN bus as a short, protected branch away from sensitive sensor signals. Validate the bus waveform, dominant and recessive states, wake-up behavior, and fault recovery at the vehicle power extremes. Exact pin assignments and recommended external components should be implemented from the manufacturer datasheet.
This page combines package, interface, environmental, and standards information with practical application guidance and an honest review of drop-in replacement availability. It also identifies where detailed electrical limits, pin descriptions, and lifecycle documentation must be confirmed before hardware release.
Bộ thay thế dễ dàng lắp đặt cho MC33662JEF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MC33662JEFR2
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC33662JEF Thông số kỹ thuật
| Product Type | LIN Bus Physical-Layer Transceiver |
| Transmitter and Receiver Count | 1 transmitter and 1 receiver |
| Bus Type | LINbus |
| Nominal Supply Voltage | 13.5 V |
| Minimum Operating Temperature | -40 °C |
| Maximum Operating Temperature | 125 °C |
| Total Pin Count | 8 pins |
| Package Type | SOIC-8 |
| Package Code | R-PDSO-G8 |
| Package Width | 3.9 mm |
| Package Length | 4.9 mm |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Application Classification | Automotive |
| ISO 17987 Support | Supported |
| LIN 2.x Support | Supported |
| SAE J2602-2 Support | Supported |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân MC33662JEF rectangular
Cấu hình chân cho MC33662JEF (rectangular gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MC33662JEF.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MC33662JEF phù hợp cho 6 Áp dụngs: Automotive Body Control Module, Door and Seat Control Module, Automotive Climate Control Panel, Lighting Control Network, Automotive Sensor Node, Vehicle Actuator Controller.
Automotive Body Control Module
The MC33662JEF fits an LIN-connected body-control module that coordinates distributed door, lighting, climate, or seat functions. Its one-transmitter/one-receiver architecture connects a host microcontroller to a LIN subnet while the 8-pin SOIC package simplifies conventional automotive PCB assembly. The -40 °C to +125 °C operating range provides environmental margin for cabin and body electronics. The LIN bus still requires the appropriate external protection and network components defined by the manufacturer application circuit, and system validation should cover dominant and recessive waveforms, wake-up behavior, bus faults, and power-transient conditions.
Được đề xuất
Door and Seat Control Module
The MC33662JEF is appropriate for door and seat control units that use LIN sub-buses to reduce wiring between switches, motors, sensors, and a local controller. The device provides one LIN transmitter and one receiver in an 8-pin SOIC package, giving the designer a compact interface to the host MCU. Its operation to 125 °C is relevant to parked-vehicle environments, although internal module temperatures must be checked against the device rating. Place the transceiver near the harness connector, route the LIN conductor away from sensitive analog signals, and verify startup, sleep, wake-up, and recovery behavior over the complete vehicle supply range.
Được đề xuất
Automotive Climate Control Panel
A climate-control panel can use the MC33662JEF to communicate with distributed temperature controls, fan commands, button modules, or actuator nodes over LIN. The 1/1 transceiver arrangement supports bidirectional bus communication through separate transmit and receive functions, while the 8-pin SOIC footprint keeps the physical interface compact. Its stated ISO 17987, LIN 2.x, and SAE J2602-2 support provides a clear physical-layer basis for network design. The implementation should still validate timing, bus loading, fault reporting, and behavior when a remote node drives the bus during startup or shutdown.
Được đề xuất
Lighting Control Network
The MC33662JEF can serve as the LIN interface in an automotive lighting control node connected to exterior lamps, switches, or light sensors. The nominal 13.5 V operating point aligns with a conventional vehicle low-voltage supply, while the -40 °C to +125 °C rating supports the broad environmental conditions encountered by body-mounted electronics. The SOIC-8 package is practical for leaded assembly and rework. Designers should confirm the transceiver's detailed supply thresholds and LIN timing from the NXP datasheet, then validate the finished node against the vehicle's wake-up, load-dump, and bus-fault requirements.
Được đề xuất
Automotive Sensor Node
The MC33662JEF is suitable for a LIN-connected sensor node that reports switch, temperature, or occupancy-related information to a central controller. A LIN subnetwork is useful when a smart sensor needs power, communication, and diagnostics over a compact harness. The MC33662JEF supplies the physical-layer transceiver required between the smart-sensor logic and the bus, with operation specified from -40 °C to +125 °C. Apply the manufacturer's recommended bus protection and decoupling arrangement, maintain a controlled return path, and test the node with realistic bus capacitance and neighboring LIN devices to confirm communication margin.
Được đề xuất
Vehicle Actuator Controller
The MC33662JEF can interface a low-bandwidth LIN actuator controller used for pumps, small motors, valves, or powered access mechanisms. Its single transmitter and receiver provide the basic physical-layer functions required by a LIN master or slave node, and the compact 8-pin SOIC package leaves board area for local power and driver circuitry. The extended automotive temperature range supports use across multiple vehicle compartments, but thermal placement still requires verification at the highest local ambient temperature. Protect the transceiver from wiring transients, follow the datasheet's external-component recommendations, and validate communication through power cycling and disconnected-node fault cases.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC33662JEF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC33662JEFR2 |
|---|---|---|
| Package | 8-pin SOIC (R-PDSO-G8) | 8-pin SOIC (R-PDSO-G8) |
| Brand | NXP Semiconductors | NXP Semiconductors |
| Transmitter and Receiver Count | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver |
| Nominal Supply Voltage | 13.5 V | 13.5 V |
| Minimum Operating Temperature | -40 °C | -40 °C |
| Maximum Operating Temperature | 125 °C | 125 °C |
| Interface Standard | ISO 17987, LIN 2.x, SAE J2602-2 | ISO 17987, LIN 2.x, SAE J2602-2 |
| Total Pin Count | 8 pins | 8 pins |
| Package Width | 3.9 mm | 3.9 mm |
| Package Length | 4.9 mm | 4.9 mm |
Bảo phân biệt quan trọng
- Automotive temperature coverage (vsMC33662JEFR2)
- Compact physical interface (vsMC33662JEFR2)
- Physical-layer compatibility (vsMC33662JEFR2)
Ghi chú thiết kế
Place the MC33662JEF and its required bypass components near the vehicle harness connector and LIN route. Keep the LIN conductor away from high-current switching nodes, crystal clocks, and sensitive sensor inputs, and provide a direct, low-impedance return path. Confirm the final track geometry, protection placement, and ground reference against the manufacturer application circuit before PCB release.
Design the module around the device's 13.5 V nominal automotive supply while protecting the MC33662JEF from wiring transients and load-dump events. Follow the NXP datasheet for supply decoupling, external protection, and operating limits, and verify startup, shutdown, sleep, and wake-up behavior with the complete vehicle power profile rather than only a laboratory supply.
Do not treat every 8-pin LIN transceiver as a pin-compatible substitute. Check the complete R-PDSO-G8 pin assignment, LIN TX/RX logic, enable behavior, supply thresholds, timing, and fault recovery for both the installed and proposed device. After substitution, test dominant and recessive waveforms, bus loading, disconnected nodes, stuck-at faults, and operation across the full vehicle temperature range.
Use the LIN network's specified rise and fall times, bus capacitance, termination strategy, and waveform margins as the acceptance criteria for signal integrity. Keep external protection capacitance from excessively slowing transitions, use a controlled reference plane, and inspect the bus with an oscilloscope at the connector during EMC testing. The -40 °C to +125 °C device rating does not by itself guarantee timing margin across the complete network.
Thông tin tuân thủ
The device is identified for automotive use, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified. Confirm these attributes with the manufacturer product documentation before qualification.