MC9S12D64VPV - 16-Bit 64KB Flash MCU | NXP | Automotive
MPN: MC9S12D64VPV ✓ AktifMC9S12D64VPV Ringkasan
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one component. The MC9S12D64 belongs to the HCS12 family, whose 16-bit architecture, mixed-signal peripherals, and automotive-oriented interfaces support applications that need more control capability than a basic 8-bit device. The S12D family also provides an upward migration path from earlier 68HC08, 68HC11, and 68HC12 architectures by combining greater memory, additional peripherals, and higher performance.
The MC9S12D64VPV integrates 64KB of flash program memory, 4KB of RAM, and 1KB of EEPROM into a single package. Its 10-bit ADC resources and 25MHz maximum clock support mixed-signal control systems where sensor acquisition, communications, and real-time control coexist. The broad 2.35V to 5.25V operating range permits design flexibility across automotive and industrial voltage environments, while the -40°C to +105°C rating supports operation across extended temperature conditions.
Within the S12D family, devices are designed with package and peripheral compatibility to support scalable platform development. The family documentation describes fully pin-compatible members with selectable memory and peripheral options, allowing a common hardware concept to move between configurations as requirements change. The MC9S12D64VPV uses a square 20mm by 20mm LQFP-112 package with gull-wing terminals, providing a high pin count for analog interfaces, communication channels, timers, and control signals.
Typical applications include automotive body and multiplexing controllers, sensor-interface modules, industrial acquisition equipment, communication nodes, and embedded control platforms. Its 16-bit processing core is useful for algorithms requiring more arithmetic range than an 8-bit microcontroller, while the integrated ADC supports direct analog measurement. Designers should also consider the comparatively high 25MHz clock when evaluating timing margins, power consumption, and peripheral clock requirements.
PCB implementation requires careful attention to the 112-terminal LQFP footprint, exposed supply routing, decoupling, and signal integrity. Place input and output decoupling capacitors close to the appropriate supply terminals, use a continuous ground plane, and route high-frequency or communication signals away from switching nodes. Firmware, clock, reset, and power-management configuration must be checked against the device user guide before production release.
This product page combines the manufacturer-family identity, verified package and memory characteristics, practical automotive and industrial use cases, package-aware comparison information, and design guidance. It is intended to help engineers locate the official MC9S12D64VPV documentation, understand the device's architectural limits, and determine whether a pin-compatible S12D family device is appropriate for an existing design.
Pilihan pengganti yang segera untuk MC9S12D64VPV — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
MC9S12DG256CPVE
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MC9S12D64VPV Penilaian maksimum & Ciri-ciri Elektrik
| Microcontroller Type | 16-bit HCS12 microcontroller |
| Architecture | 16-bit CISC |
| Frekuensi Klock Maksimum | 25 MHz |
| Flash Memory | 64 KB |
| RAM | 4 KB |
| EEPROM | 1 KB |
| ADC Resolution | 10 bit |
| Operating Voltage Range | 2.35 V to 5.25 V |
| Gambaran Suhu Operasi | -40°C to +105°C |
| Temperature Grade | Industrial |
| Package Type | LQFP-112, gull-wing terminal |
| Package Body Size | 20 mm × 20 mm |
| Package Shape | Square |
| Terminal Count | 112 terminals |
| Core Family | HCS12 |
| Family Design | Flash-based 16-bit MCU for automotive multiplexing applications |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin MC9S12D64VPV square
Konfigurasi pin untuk MC9S12D64VPV (square pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk MC9S12D64VPV.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
MC9S12D64VPV patut untuk 6 aplikasis: Automotive Body Multiplexing Controller, Automotive Sensor Interface Module, Industrial Data Acquisition Controller, Industrial Communication Node, Embedded Motor and Actuator Control, Programmable Logic Controller.
Automotive Body Multiplexing Controller
The MC9S12D64VPV fits automotive body and multiplexing controllers because it combines a 16-bit HCS12 core, 25MHz clock, and integrated flash, RAM, and EEPROM in one device. Its 2.35V to 5.25V operating range and -40°C to +105°C temperature specification support extended-temperature embedded systems. The 112-terminal LQFP exposes the interfaces needed for distributed body nodes, switches, sensors, and diagnostic signaling. Compared with a simple 8-bit controller, the 16-bit architecture provides greater arithmetic and addressing capability, although designers should confirm AEC-Q100 qualification for the exact production program.
Disebarkan
Automotive Sensor Interface Module
The MC9S12D64VPV is suitable for an automotive sensor interface because it includes a 10-bit ADC, 4KB of RAM, 1KB of EEPROM, and 25MHz processing performance. The MCU can sample analog inputs, apply calibration or filtering, and manage associated communication and control functions within a compact embedded platform. Its -40°C to +105°C rating is appropriate for many vehicle-cabin and exterior sensing environments, while the 112-terminal package provides substantial I/O capacity. Validate analog accuracy, channel multiplexing, and qualification requirements in the family documentation before deployment.
Disebarkan
Industrial Data Acquisition Controller
The MC9S12D64VPV can serve as an industrial acquisition controller when a design requires deterministic 16-bit processing alongside a 10-bit ADC. Its 25MHz clock supports time-based sampling and control tasks, while 64KB of flash, 4KB of RAM, and 1KB of EEPROM support firmware, working state, and parameter storage. The device operates from 2.35V to 5.25V across -40°C to +105°C, making it suitable for robust equipment environments. Engineers should budget external signal conditioning, isolation, precision references, and protection where sensor inputs exceed the MCU's direct interface limits.
Disebarkan
Industrial Communication Node
The MC9S12D64VPV is appropriate for a communication node that needs more capability than an 8-bit MCU while retaining a modest embedded memory footprint. Its 16-bit HCS12 architecture, 25MHz maximum clock, and 64KB flash can support protocol processing, local diagnostics, and application logic. The LQFP-112 package provides numerous signal options for communications and control functions, and the 2.35V to 5.25V supply range supports embedded industrial rails. Pin multiplexing, timing, transceiver requirements, and interrupt latency should be verified against the device user guide for the selected peripheral set.
Disebarkan
Embedded Motor and Actuator Control
The MC9S12D64VPV can coordinate actuators in motor, valve, and pump control subsystems where 16-bit arithmetic, real-time timers, analog feedback, and communication are required. The 25MHz core and 64KB flash provide room for control algorithms and diagnostics, while 4KB of RAM supports working state. Its 112-terminal LQFP package offers ample external connections for control outputs and feedback inputs. The main engineering trade-off is that software must manage timing, debouncing, fault handling, and protection consistently with the power stage and the MCU's specified operating limits.
Disebarkan
Programmable Logic Controller
The MC9S12D64VPV is well suited to compact PLC-style controllers because it combines flash-resident application code, EEPROM for configuration or calibration values, RAM for runtime state, and a 16-bit real-time core. Its 10-bit ADC supports basic analog process inputs, while 25MHz operation provides timing margin for scanning and control tasks. The industrial temperature range of -40°C to +105°C supports harsh installations, and the LQFP-112 package provides extensive I/O options. Production designs should include watchdog handling, brownout behavior, isolation strategy, and validated I/O protection.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MC9S12D64VPV — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MC9S12DG256CPVE |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | LQFP-112, 20mm × 20mm | LQFP-112 |
| Core Architecture | 16-bit HCS12 CISC | 16-bit HCS12 CISC |
| Maximum Clock Frequency | 25 MHz | 25 MHz |
| Flash Memory | 64 KB | 256 KB (+300%) |
| RAM | 4 KB | 12 KB (+200%) |
| Operating Voltage Range | 2.35 V to 5.25 V | 2.5 V / 5 V automotive configuration |
| Terminal Count | 112 terminals | 112 terminals |
Penyeberangsung Jelas
- Lower memory configuration for cost-sensitive embedded control (vsMC9S12DG256CPVE)
- Same package and core-clock migration path (vsMC9S12DG256CPVE)
- Documented 10-bit conversion capability (vsMC9S12DG256CPVE)
Catatan Desain
Design the board around the manufacturer's 112-terminal LQFP land pattern and preserve pin numbering from the package drawing. Place every required supply bypass capacitor close to its corresponding power terminal, connect the device ground pins to a continuous ground plane, and avoid routing communication or ADC signals beneath noisy supply paths. Confirm exposed thermal requirements and recommended PCB construction in the package documentation before release.
Use separate local paths for digital and analog supply distribution when sensitive ADC measurements are required, then join them at a controlled ground reference. Select bypass capacitors and their voltage ratings according to the electrical-characteristics guidance. Transient protection must be designed for the actual automotive or industrial environment rather than inferred solely from the 2.35V to 5.25V operating range.
Do not assume that equal package dimensions guarantee a functional drop-in replacement. Compare pin multiplexing, power pins, reset and clock functions, peripheral resources, memory-map assumptions, and software support between the MC9S12D64VPV and the selected alternative. The MC9S12DG256CPVE shares the LQFP-112 package and 25MHz core class, but its larger memory configuration requires a firmware and validation review.
Assign ADC channels, communication interfaces, timers, and debug signals from the manufacturer pin-description table before laying out the PCB. Keep analog inputs away from switching-power nodes and provide a low-impedance reference return. If the MCU processes captured waveforms, verify the required ADC acquisition rate and peripheral timing against the 25MHz system clock rather than inferring performance from clock frequency alone.
Estimated: power dissipation is P = VIN × ICORE plus the power consumed by active peripherals and I/O loads. The resulting junction-temperature estimate is TJ = TA + P × thermal resistance, using the manufacturer thermal model and the intended PCB copper area. Validate worst-case activity, supply voltage, and ambient temperature because the operating-temperature range alone does not establish safe board-level dissipation.
Maklumat Kesediaan
The device is described for automotive multiplexing applications and has an industrial temperature range, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is included in the available product information. Request current compliance documents for the exact ordering code through the Request a Quote form.