MC9S12H256VPV - 16-Bit 50MHz 256KB MCU | NXP
MPN: MC9S12H256VPV ✗ Akhir HayatMC9S12H256VPV Ringkasan
A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and interface logic on one die. The MC9S12H256VPV belongs to the HCS12 family, whose CPU12 architecture provides a 16-bit instruction set for embedded control. Automotive electronic control units use this combination of deterministic control, serial communication, and mixed-signal peripherals to supervise actuators, sensors, communication networks, and vehicle body functions.
The principal device characteristics are a 16-bit CPU12 core, 50 MHz maximum clocking, and 256 KB of embedded flash memory. The device is offered in a 112-LQFP gull-wing package with a 20 mm by 20 mm body. These parameters make it suitable for automotive control modules that require substantial firmware storage while retaining the peripheral integration and package density expected in body and chassis electronics.
The HCS12 platform integrates flash program memory and an automotive communication architecture into the same device. The flash memory allows field-oriented firmware to be retained without an external program-memory chip. The package exposes 112 terminals for power, ground, clock, reset, programming, communications, and mixed-signal functions, supporting both legacy HCS12 module designs and compact controller assemblies.
Typical uses include automotive body-control modules, sensor-interface controllers, communication gateways, actuator controllers, and compact electronic control units. A 256 KB flash allocation can hold application code, calibration information, diagnostic routines, and communication stacks, while the 16-bit CPU supports control-loop processing across automotive subsystems.
Designers should preserve the exact 112-LQFP land pattern, power architecture, clocking arrangement, and peripheral assignments when creating a replacement. Reuse of an existing board also requires reviewing operating limits, errata, initialization code, interrupt configuration, and toolchain compatibility rather than comparing the processor clock and flash size alone.
This page combines the exact catalog identity, package information, sourcing guidance, compatible family references, and engineering-oriented selection criteria. It also distinguishes direct hardware reuse from broader HCS12 migration choices so procurement and design teams can assess compatibility without relying on part-number similarity alone.
Pilihan pengganti yang segera untuk MC9S12H256VPV — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MC9S12H256VPV (sama faktor bentuk dan kaki) — berbeza dalam Package.
MC9S12H256VPVE
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MC9S12DP256BMPV
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MC9S12H256VPV Penilaian maksimum & Ciri-ciri Elektrik
| Microcontroller Type | 16-bit HCS12 microcontroller |
| Processor Core | CPU12 |
| Frekuensi Klock Maksimum | 50 MHz |
| Program Memory Size | 256 KB (256K x 8) |
| Program Memory Type | Flash |
| Kemasan | 112-LQFP (20 mm x 20 mm) |
| Number of Terminals | 112 terminals |
| Terminal Form | Gull wing |
| Package Shape | Square |
| Technology | CMOS |
| Series | MC9S12 |
Panduan Konfigurasi Pin MC9S12H256VPV square
Konfigurasi pin untuk MC9S12H256VPV (square pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk MC9S12H256VPV.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
MC9S12H256VPV patut untuk 6 aplikasis: Automotive Body Control Module, Vehicle Sensor Interface Controller, Automotive Communication Gateway, Actuator Control Module, Automotive Diagnostic Interface, Legacy Platform Controller.
Automotive Body Control Module
The MC9S12H256VPV fits a body-control module that coordinates switches, lamps, locks, and other vehicle-body functions. Its 16-bit CPU12 core and listed 50 MHz operating point provide processing capacity for control logic, diagnostics, and communication handling. The 256 KB flash budget can hold application routines, lookup data, diagnostic services, and configuration information. The 112-LQFP package also exposes a broad set of automotive-oriented I/O. During integration, verify every peripheral assignment, interrupt vector, and power rail against the exact package documentation, and review initialization differences before updating an existing control-module design.
Disebarkan
Vehicle Sensor Interface Controller
A sensor-interface controller can use the MC9S12H256VPV to acquire and process signals from switches, resistive sensors, and digital sensors before forwarding results to a vehicle network. The 50 MHz listed CPU12 clock supports responsive control and communication tasks, while 256 KB of flash provides room for calibration tables and diagnostic firmware. Its mixed-signal HCS12 heritage is valuable when a design must combine digital control with analog measurement functions. The key design checks are the ADC and sensor-interface details, electrical input limits, reference accuracy, and pin multiplexing. Those characteristics must be confirmed in the MC9S12H256 device documentation for the exact operating and qualification conditions.
Disebarkan
Automotive Communication Gateway
The MC9S12H256VPV is appropriate for a communication gateway that translates or supervises traffic between vehicle modules. Its 16-bit CPU architecture and 256 KB flash allocation support protocol handling, diagnostic logic, routing tables, and application services. The 112-LQFP footprint provides numerous external connections for CAN, serial, programming, and signal-conditioning functions, subject to the device's actual peripheral allocation. Designers should compare interrupt latency, serial timing, bus transceiver interfaces, and clock configuration with the original system requirements. Because MC9S12 family members can differ in peripheral sets and startup behavior, firmware and schematics must be reviewed rather than assuming identical software support.
Disebarkan
Actuator Control Module
In an actuator-control module, the MC9S12H256VPV can supervise outputs that drive pumps, valves, relays, or motors through external power stages. Its listed 50 MHz CPU12 core supports responsive state-machine execution, fault detection, and diagnostic reporting. The 256 KB flash capacity allows substantial control code plus lookup tables without requiring an external program-memory device. The 112-LQFP package offers enough pins for multiple control signals, communication links, and debugging functions, although the actual I/O count depends on the selected peripheral multiplexing. Production design work should include worst-case timing, output-state verification, watchdog behavior, brownout response, and validation of external driver interfaces.
Disebarkan
Automotive Diagnostic Interface
The MC9S12H256VPV can serve as the controller for a diagnostic interface that receives service requests, evaluates input channels, and returns status information. Its 16-bit CPU12 architecture supports structured protocol and diagnostic routines, and the 256 KB flash region can store diagnostic data, identifiers, and service software. The 112-LQFP package supports integration with vehicle communication circuitry, programming connectors, and discrete input channels. Engineers should verify the serial interface timing, interrupt priorities, clock tree, and watchdog behavior for the intended diagnostic response time. Firmware qualification should include power-cycle states, bus-off handling, corrupted-message tests, and compatibility with the vehicle's diagnostic standard.
Disebarkan
Legacy Platform Controller
The MC9S12H256VPV is well suited to maintaining or cloning a legacy embedded platform where changing the microcontroller architecture would create unnecessary risk. Its 50 MHz listed operating point and 256 KB flash memory provide the processing and storage profile associated with HCS12 body and chassis electronics. The 112-LQFP package enables board-level reuse when the alternative retains equivalent dimensions and electrical characteristics. A migration should begin with a complete pin-function comparison, followed by startup, timer, serial, analog, and interrupt validation. Existing binaries may require recompilation or initialization changes if the selected replacement belongs to a related but distinct MC9S12 variant.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MC9S12H256VPV — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MC9S12H256VPVE | MC9S12DP256BMPV |
|---|---|---|---|
| Package | 112-LQFP (20 mm x 20 mm) | 112-LQFP (20 mm x 20 mm) | 112-LQFP |
| Brand | NXP | NXP | NXP |
| Processor Architecture | 16-bit CPU12 | 16-bit HCS12 | 16-bit HCS12 |
| Program Memory | 256 KB (256K x 8) flash | 256 KB (256K x 8) flash | 256 KB (256K x 8) flash |
| Series | MC9S12 | MC9S12 | MC9S12 |
| Terminal Count | 112 terminals | 112 terminals | 112 terminals |
Penyeberangsung Jelas
- Higher listed operating point within the identified package options (vsMC9S12H256VPVE)
- Matches the MC9S12H256 exact-family flash configuration (vsMC9S12DP256BMPV)
- Identifies the exact ordering option for legacy maintenance (vsMC9S12DP256BMPV)
Catatan Desain
Treat the 112-LQFP footprint as a constrained, high-pin-count layout. Preserve the package dimensions, lead pitch, exposed or non-exposed pad arrangement, pin-1 orientation, and solder-mask land pattern specified for the exact package drawing. Route programming, clock, reset, communication, and power pins against the manufacturer pin-description table rather than relying on the approximate square outline. After substitution, use an ERC and pin-assignment comparison to identify power, ground, and multiplexed peripheral changes before release.
Do not select a replacement solely from package, flash size, and family name. Compare the startup clock configuration, oscillator requirements, watchdog behavior, reset sources, interrupt priorities, timer channels, serial interfaces, ADC functions, and peripheral pin multiplexing. The 50 MHz target and 16 MHz MC9S12H256VPVE have materially different timing headroom, and a related MC9S12 variant may require different initialization code. Validate with timer measurements, communication-loop tests, and fault-injection testing.
Confirm the exact device's input-voltage range, I/O voltage domains, power-up sequence, and brownout behavior from the manufacturer documentation before finalizing decoupling and protection. Place the required bulk and high-frequency capacitors according to the reference layout and keep sensitive clock and communication routes away from switching nodes. Because package-level alternatives may expose different multiplexing or voltage-domain assignments, verify every externally connected signal against the alternate part's pin table and operating limits.
Calculate the controller's worst-case dissipation from the actual supply voltage, I/O loading, clock activity, and ambient temperature rather than relying only on the 50 MHz operating point. The 112-LQFP package can provide substantial board-area heat spreading, but copper connectivity and airflow remain important in a sealed automotive enclosure. Validate thermal performance at the highest expected ambient temperature and with adjacent converters or power stages operating concurrently.
Maklumat Kesediaan
The available catalog information identifies an automotive HCS12 MCU and an industrial package designation but does not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements. These fields remain unknown pending manufacturer documentation.