MCP6044-E/ST - 14 kHz Quad CMOS Op Amp | Microchip
MPN: MCP6044-E/ST ✓ AktifMCP6044-E/ST Ringkasan
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. Its place in the larger hierarchy is analog IC -> operational amplifier -> quad low-power amplifier -> CMOS mixed-signal semiconductor. The quad configuration integrates four amplifiers into one package, reducing board area when a design needs multiple identical low-power amplification channels.
The MCP6044-E/ST combines low bias current with rail-to-rail operation. Microchip's advanced CMOS process supports low power consumption, high open-loop gain, and output swing that approaches the supply rails. Each amplifier is intended for general-purpose signal conditioning, including buffering, voltage amplification, active filtering, and level translation within low-voltage systems.
Its low operating current makes the MCP6044-E/ST suitable for battery-operated equipment where every microamp of supply demand affects runtime. The 1.4 V minimum operating supply extends operation into coin-cell and energy-harvesting systems, while the 6 V maximum rating accommodates conventional 3.3 V and 5 V rails. Rail-to-rail inputs and outputs also improve usable signal range in low-voltage sensing circuits.
Typical applications include industrial process-control interfaces, portable instrumentation, wearable products, low-power sensor conditioning, and mixed-signal sensor nodes. Quad channel count is especially useful when four transducers, resistive dividers, or analog-front-end stages need consistent gain and bandwidth.
Design with the op amp's input common-mode range, output swing, load capability, and stability requirements in mind. Place each decoupling capacitor close to the supply pins and use short, low-leakage signal paths because the low bias current specification makes board contamination and leakage relevant.
This page combines manufacturer specifications, package information, commercial sourcing guidance, and practical design notes to help engineers evaluate the MCP6044-E/ST beyond a basic manufacturer datasheet summary.
Pilihan pengganti yang segera untuk MCP6044-E/ST — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MCP6044-E/ST (sama faktor bentuk dan kaki) — berbeza dalam Input Offset Voltage, Number of Amplifiers, Package.
MCP6044T-E/ST
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MCP6044T-I/ST
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MCP6044T-E/STVAO
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MCP6044-I/ST
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MCP6044-E/ST Penilaian maksimum & Ciri-ciri Elektrik
| Number of Amplifiers | 4 amplifiers |
| Gain-Bandwidth Product | 14 kHz |
| Typical Operating Current | 600 nA |
| Input Offset Voltage | < 3 mV |
| Minimum Operating Supply | 1.4 V |
| Maximum Operating Supply | 6 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Process Technology | Advanced CMOS |
| Amplifier Type | General-purpose operational amplifier |
| Kemasan | 14-lead TSSOP (0.173 in, 4.40 mm width) |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin MCP6044-E/ST 14-lead tssop (0.173 in, 4.40 mm width)
Konfigurasi pin untuk MCP6044-E/ST (14-lead tssop (0.173 in, 4.40 mm width) pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk MCP6044-E/ST.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
MCP6044-E/ST patut untuk 6 aplikasis: Low-Power Sensor Signal Conditioning, Battery-Powered Portable Instruments, Industrial Process-Control Interfaces, Wearable and Portable Health Devices, Active Filters and Signal Conditioning, Data-Acquisition Front Ends.
Low-Power Sensor Signal Conditioning
The MCP6044-E/ST is appropriate for conditioning four low-frequency sensor channels because its rail-to-rail inputs accept signals close to the supply limits while its 600 nA typical operating current limits the load placed on an energy-limited source. Each amplifier can buffer a resistive divider or sensor output before conversion by an ADC. The 14 kHz gain-bandwidth product is suitable for slowly varying signals rather than fast pulses, and the input offset below 3 mV should be included in the error budget for divider-based measurements.
Disebarkan
Battery-Powered Portable Instruments
The MCP6044-E/ST works well in portable instruments operated from a single low-voltage battery because the family operates from 1.4 V to 6 V and consumes only 600 nA of typical operating current. The four channels can amplify bridge, resistive, or photodiode-oriented signals without requiring four separate amplifier packages. Because total battery consumption includes sensor current and external loads, use the manufacturer's maximum quiescent-current limits for worst-case runtime calculations and verify that every amplifier is in a valid operating state.
Disebarkan
Industrial Process-Control Interfaces
The MCP6044-E/ST can provide the first analog stage for industrial process-control inputs such as pressure, temperature, or position sensors. Rail-to-rail input and output operation increases usable signal swing on 1.4 V to 6 V supplies, while four channels in one 14-lead TSSOP package simplify board partitioning. The 14 kHz bandwidth suits slow process variables rather than high-rate communications. Verify input protection, grounding strategy, and the amplifier's noise behavior against the required sensor and cable environment.
Disebarkan
Wearable and Portable Health Devices
The MCP6044-E/ST is suitable for wearable and portable health-device signal chains that need several low-power analog channels in a compact package. Its 600 nA typical operating current reduces the continuous load, and the rail-to-rail input capability supports low-amplitude signals from resistive or bio-sensing interfaces. Four amplifier sections can handle electrode buffering, bias generation, or filtering, although the 14 kHz bandwidth is better aligned with slow physiological signals than with wideband acquisition. Medical designs also require application-specific safety and validation work.
Disebarkan
Active Filters and Signal Conditioning
The MCP6044-E/ST can implement first-order active filters, transimpedance stages, and general signal-conditioning networks where a 14 kHz gain-bandwidth product is adequate. Four independent amplifiers make it practical to build cascaded conditioning blocks or several matched channels. Stable operation with the selected capacitor values and load must be confirmed in simulation and measurement, especially at low supply voltages. The amplifier's low operating current is valuable in battery systems, but leakage from PCB contamination can become significant when bias currents are very low.
Disebarkan
Data-Acquisition Front Ends
The MCP6044-E/ST can buffer or amplify four channels ahead of a multiplexed analog-to-digital converter in a compact data-acquisition system. Its low bias current and 600 nA typical operating current are helpful when the converter itself requires low power, while rail-to-rail inputs improve utilization of the available supply range. The amplifier bandwidth limits how quickly it can settle between multiplexed channel changes, so calculate acquisition time using the required gain, source impedance, and settling accuracy. Add protection and filtering ahead of sensitive inputs.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MCP6044-E/ST — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MCP6044T-E/ST | MCP6044T-I/ST | MCP6044T-E/STVAO | MCP6044-I/ST |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 14-lead TSSOP | 14-lead TSSOP - same | 14-lead TSSOP - same | 14-lead TSSOP - same | 14-lead TSSOP - same |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 |
| Gain-Bandwidth Product | 14 kHz | 14 kHz | 14 kHz | 14 kHz | 14 kHz |
| Typical Operating Current | 600 nA | 600 nA | 600 nA | 600 nA | 600 nA |
| Supply Voltage Range | 1.4 V to 6 V | 1.4 V to 6 V | 1.4 V to 6 V | 1.4 V to 6 V | 1.4 V to 6 V |
| Input Offset Voltage | < 3 mV | < 3 mV | < 3 mV | < 3 mV | < 3 mV |
| Input and Output Capability | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
| Operating Temperature Grade | E-grade ordering option | T-E ordering option | I-grade ordering option | VAO ordering option | I-grade ordering option |
Penyeberangsung Jelas
- Four low-power amplifier channels in one surface-mount package (vsMCP6044T-E/ST)
- Operation from low-voltage single supplies (vsMCP6044T-I/ST)
- Low quiescent current for portable designs (vsMCP6044T-E/STVAO)
Catatan Desain
Calculate the amplifier's static supply demand from the 600 nA typical operating-current figure and the selected supply voltage, then add load and sensor currents. Use the manufacturer's maximum quiescent-current and output-current limits for a worst-case battery-life estimate. Because the MCP6044-E/ST supports operation down to 1.4 V, confirm that downstream sensors, ADC inputs, and digital logic remain within valid voltage ranges at the minimum system supply.
Place the supply bypass capacitor directly across the device's supply and ground pins, with a short, low-inductance connection and no excessive series resistance between the capacitor and IC. Route each amplifier input away from switching nodes and high-current return paths. The very low bias current makes PCB contamination and surface leakage potentially significant, so use clean boards, suitable conformal protection where required, and guard techniques for very high-impedance sources.
Do not assume that every quad op amp with a 14-lead TSSOP outline is interchangeable. Verify the channel pin order, supply pins, input and output positions, and maximum input voltage. Also distinguish temperature grades and qualification ordering codes before changing the part number. For the MCP6044 family, the 14 kHz gain-bandwidth product can also be insufficient for fast edges or high-rate signals even when the basic topology appears compatible.
Check settling time against the required gain and sample rate before using the amplifier in a multiplexed measurement path. Higher closed-loop gain reduces usable bandwidth, and capacitive input loading can alter effective bandwidth and stability. For sensor cables, place protection and anti-alias filtering close to the connector. Confirm common-mode range, output swing, and capacitive-load behavior in the manufacturer's electrical-characteristics and application information.
Maklumat Kesediaan
The manufacturer product page confirms the MCP6044 family and available packages but does not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals classifications for this ordering code. Automotive ordering options should not be assumed to apply to MCP6044-E/ST without the corresponding qualification documentation.