Microchip Technology

MCP6044-E/ST - 14 kHz Quad CMOS Op Amp | Microchip

N.º da peça: MCP6044-E/ST ✓ Ativo
< 3 mV Vdss 600 nA Id 14-lead TSSOP (0.173 in, 4.40 mm width) Package
MOQ: 1 |

MCP6044-E/ST Visão geral

The Microchip Technology MCP6044-E/ST is a quad CMOS operational amplifier with a 14 kHz gain-bandwidth product, typical operating current of 600 nA, and input offset voltage below 3 mV. The device supports single-supply operation from 1.4 V to 6 V and provides rail-to-rail input and output capability in a 14-lead TSSOP package.

An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. Its place in the larger hierarchy is analog IC -> operational amplifier -> quad low-power amplifier -> CMOS mixed-signal semiconductor. The quad configuration integrates four amplifiers into one package, reducing board area when a design needs multiple identical low-power amplification channels.

The MCP6044-E/ST combines low bias current with rail-to-rail operation. Microchip's advanced CMOS process supports low power consumption, high open-loop gain, and output swing that approaches the supply rails. Each amplifier is intended for general-purpose signal conditioning, including buffering, voltage amplification, active filtering, and level translation within low-voltage systems.

Its low operating current makes the MCP6044-E/ST suitable for battery-operated equipment where every microamp of supply demand affects runtime. The 1.4 V minimum operating supply extends operation into coin-cell and energy-harvesting systems, while the 6 V maximum rating accommodates conventional 3.3 V and 5 V rails. Rail-to-rail inputs and outputs also improve usable signal range in low-voltage sensing circuits.

Typical applications include industrial process-control interfaces, portable instrumentation, wearable products, low-power sensor conditioning, and mixed-signal sensor nodes. Quad channel count is especially useful when four transducers, resistive dividers, or analog-front-end stages need consistent gain and bandwidth.

Design with the op amp's input common-mode range, output swing, load capability, and stability requirements in mind. Place each decoupling capacitor close to the supply pins and use short, low-leakage signal paths because the low bias current specification makes board contamination and leakage relevant.

This page combines manufacturer specifications, package information, commercial sourcing guidance, and practical design notes to help engineers evaluate the MCP6044-E/ST beyond a basic manufacturer datasheet summary.

Alternativas drop-in para MCP6044-E/ST — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com MCP6044-E/ST (mesmo formato e footprint) — diferindo em Input Offset Voltage, Number of Amplifiers, Package.

Microchip Technology
Input Offset Voltage: 3 mV
Number of Amplifiers: 4 channels
Package: 14-pin TSSOP

MCP6044T-E/ST

✅ Drop-In
📦 14-lead TSSOP
Same quad low-power amplifier family and 14-lead TSSOP footprint; ordering-code temperature or qualification classification must be confirmed

📋 Alternativa de referência (fora do catálogo)

MCP6044T-I/ST

✅ Drop-In
📦 14-lead TSSOP
Same quad amplifier architecture and 14-lead TSSOP footprint; I-grade operating-temperature classification differs from the E-grade target

📋 Alternativa de referência (fora do catálogo)

MCP6044T-E/STVAO

✅ Drop-In
📦 14-lead TSSOP
Same 14-lead TSSOP quad amplifier family; VAO ordering option identifies a different qualification or marking configuration

📋 Alternativa de referência (fora do catálogo)

MCP6044-I/ST

✅ Drop-In
Microchip Technology
📦 14-lead TSSOP
4 channels · 1.4 V to 5.5 V · 6 V · Rail-to-rail · Rail-to-rail · 14 kHz · 3 V/µs · 170 nV/√Hz at 1 kHz

Consulte o preço

Ver ficha técnica →

MCP6044-E/ST Classificações máximas e características elétricas

Number of Amplifiers 4 amplifiers
Gain-Bandwidth Product 14 kHz
Typical Operating Current 600 nA
Input Offset Voltage < 3 mV
Minimum Operating Supply 1.4 V
Maximum Operating Supply 6 V
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Process Technology Advanced CMOS
Amplifier Type General-purpose operational amplifier
Encapsulamento 14-lead TSSOP (0.173 in, 4.40 mm width)
Tipo de montagem Surface mount

Guia de Configuração de Pinos do MCP6044-E/ST 14-lead tssop (0.173 in, 4.40 mm width)

Configuração de pinos para MCP6044-E/ST (pacote 14-lead tssop (0.173 in, 4.40 mm width)). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.

Diagrama de pinagem do pacote 14-lead tssop (0.173 in, 4.40 mm width) para MCP6044-E/ST

Nenhum dado detalhado de pinagem disponível para MCP6044-E/ST.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

MCP6044-E/ST é adequado para 6 aplicaçãos: Low-Power Sensor Signal Conditioning, Battery-Powered Portable Instruments, Industrial Process-Control Interfaces, Wearable and Portable Health Devices, Active Filters and Signal Conditioning, Data-Acquisition Front Ends.

🧩

Low-Power Sensor Signal Conditioning

The MCP6044-E/ST is appropriate for conditioning four low-frequency sensor channels because its rail-to-rail inputs accept signals close to the supply limits while its 600 nA typical operating current limits the load placed on an energy-limited source. Each amplifier can buffer a resistive divider or sensor output before conversion by an ADC. The 14 kHz gain-bandwidth product is suitable for slowly varying signals rather than fast pulses, and the input offset below 3 mV should be included in the error budget for divider-based measurements.

🔋

Battery-Powered Portable Instruments

The MCP6044-E/ST works well in portable instruments operated from a single low-voltage battery because the family operates from 1.4 V to 6 V and consumes only 600 nA of typical operating current. The four channels can amplify bridge, resistive, or photodiode-oriented signals without requiring four separate amplifier packages. Because total battery consumption includes sensor current and external loads, use the manufacturer's maximum quiescent-current limits for worst-case runtime calculations and verify that every amplifier is in a valid operating state.

🏭

Industrial Process-Control Interfaces

The MCP6044-E/ST can provide the first analog stage for industrial process-control inputs such as pressure, temperature, or position sensors. Rail-to-rail input and output operation increases usable signal swing on 1.4 V to 6 V supplies, while four channels in one 14-lead TSSOP package simplify board partitioning. The 14 kHz bandwidth suits slow process variables rather than high-rate communications. Verify input protection, grounding strategy, and the amplifier's noise behavior against the required sensor and cable environment.

💊

Wearable and Portable Health Devices

The MCP6044-E/ST is suitable for wearable and portable health-device signal chains that need several low-power analog channels in a compact package. Its 600 nA typical operating current reduces the continuous load, and the rail-to-rail input capability supports low-amplitude signals from resistive or bio-sensing interfaces. Four amplifier sections can handle electrode buffering, bias generation, or filtering, although the 14 kHz bandwidth is better aligned with slow physiological signals than with wideband acquisition. Medical designs also require application-specific safety and validation work.

📡

Active Filters and Signal Conditioning

The MCP6044-E/ST can implement first-order active filters, transimpedance stages, and general signal-conditioning networks where a 14 kHz gain-bandwidth product is adequate. Four independent amplifiers make it practical to build cascaded conditioning blocks or several matched channels. Stable operation with the selected capacitor values and load must be confirmed in simulation and measurement, especially at low supply voltages. The amplifier's low operating current is valuable in battery systems, but leakage from PCB contamination can become significant when bias currents are very low.

🖥️

Data-Acquisition Front Ends

The MCP6044-E/ST can buffer or amplify four channels ahead of a multiplexed analog-to-digital converter in a compact data-acquisition system. Its low bias current and 600 nA typical operating current are helpful when the converter itself requires low power, while rail-to-rail inputs improve utilization of the available supply range. The amplifier bandwidth limits how quickly it can settle between multiplexed channel changes, so calculate acquisition time using the required gain, source impedance, and settling accuracy. Add protection and filtering ahead of sensitive inputs.

Resumo dos produtos recomendados

MCP6044T-E/ST Same quad low-power amplifier family in the same TSSOP footprint Usado em: Low-Power Sensor Signal Conditioning, Battery-Powered Portable Instruments, Industrial Process-Control Interfaces, Wearable and Portable Health Devices, Active Filters and Signal Conditioning, Data-Acquisition Front Ends MCP6044T-I/ST Temperature-grade variant for low-power signal conditioning Usado em: Low-Power Sensor Signal Conditioning, Wearable and Portable Health Devices, Data-Acquisition Front Ends MCP6044-I/ST Microchip Technology Usado em: Battery-Powered Portable Instruments, Active Filters and Signal Conditioning MCP6044T-E/STVAO Ordering option for designs requiring a qualified TSSOP configuration Usado em: Industrial Process-Control Interfaces
What is the MCP6044-E/ST?
The MCP6044-E/ST is a Microchip Technology quad CMOS operational amplifier designed for low-voltage, low-power signal-conditioning applications. According to the manufacturer product page, the device provides a 14 kHz gain-bandwidth product, 600 nA typical operating current, input offset voltage below 3 mV, and rail-to-rail input and output operation. Four amplifiers are integrated in a 14-lead TSSOP package, making the device suitable for compact four-channel sensor, filtering, or buffering circuits.
What is the operating voltage of MCP6044-E/ST?
The MCP6044-E/ST operates from a single supply of 1.4 V to 6 V. Microchip describes the family as supporting single-supply voltage as low as 1.4 V, while the 6 V upper limit covers common 3.3 V and 5 V systems. Its rail-to-rail inputs and outputs allow the amplifier to operate across a large portion of the available supply range, although designers should verify signal amplitude, output load, and stability requirements in the application circuit.
Where can I download the MCP6044-E/ST datasheet?
The MCP6044-E/ST datasheet is available through the Microchip MCP6044 product page at https://www.microchip.com/en-us/product/MCP6044. The manufacturer page provides the device overview, package options, and technical documentation for the MCP6041/2/3/4 family. Use the pin-description table and electrical-characteristics tables in the manufacturer datasheet when assigning PCB tracks, selecting resistor values, and confirming production test limits.
Where can I find the MCP6044-E/ST pinout?
The MCP6044-E/ST pinout is shown in the Microchip MCP6044 datasheet and is consistent with the 14-lead TSSOP footprint. Use the package drawing to identify the power pins, each amplifier's inverting and non-inverting inputs, and its output. Assign tracks using the numbered pin-description table rather than relying on a generic operational-amplifier layout, because channel ordering and supply-pin positions must match the selected package exactly.
How much current does the MCP6044-E/ST consume?
The MCP6044-E/ST has a typical operating current of 600 nA, according to the Microchip product page. That low current figure makes it appropriate for battery-powered instrumentation, wearables, and other long-duration sensing systems. The number of active channels and the operating voltage affect total consumption, so confirm the worst-case quiescent current and any load current in the final system using the manufacturer's electrical-characteristics tables.
Is MCP6044-E/ST suitable for low-voltage sensor conditioning?
Yes, the MCP6044-E/ST is well suited to low-voltage sensor conditioning because it operates from 1.4 V to 6 V, provides rail-to-rail input and output behavior, and consumes only 600 nA of typical operating current. It can buffer thermistor, resistive-divider, and low-frequency sensor outputs, but the 14 kHz gain-bandwidth product limits it to low-bandwidth signal paths rather than high-frequency communications or waveform conditioning.
MCP6044-E/ST vs MCP6044T-E/ST - which is the better choice?
Choose the MCP6044-E/ST when the design requires the extended-temperature ordering option identified by the E suffix, and choose MCP6044T-E/ST when the standard automotive or temperature grade is the required procurement configuration. Both are Microchip quad amplifiers in the same 14-lead TSSOP family, but ordering codes, qualification classifications, and operating-temperature limits can differ. Confirm the exact temperature grade and qualification status against the manufacturer product page before releasing the BOM.
What is the difference between MCP6044-E/ST and MCP6044-E/P?
The MCP6044-E/ST and MCP6044-E/P use the same quad operational-amplifier family, but their packages differ. MCP6044-E/ST is supplied in a 14-lead TSSOP surface-mount package, while MCP6044-E/P is offered in a 14-pin PDIP through-hole package. MCP6044-E/ST therefore suits compact surface-mounted designs, whereas MCP6044-E/P can simplify prototyping and through-hole assembly. The package change requires a different PCB footprint and is not a board-level drop-in replacement.
When should I choose MCP6044-E/ST instead of a discrete op-amp circuit?
Choose the MCP6044-E/ST when the design needs up to four matched, general-purpose amplifier channels in a small surface-mount package and can work within a 14 kHz gain-bandwidth product. Integrating four amplifiers reduces component count and board area while providing rail-to-rail input and output capability. Use discrete amplifiers instead when the application requires higher bandwidth, lower offset, higher precision, lower noise, specialized shutdown behavior, or a package already fixed by the PCB.
What can replace the MCP6044-E/ST?
The closest replacements are Microchip MCP6044 variants that retain the quad-amplifier architecture and 14-lead TSSOP footprint, such as MCP6044T-E/ST and MCP6044T-I/ST. Their temperature and qualification ordering options must be checked before substitution. A different manufacturer's quad amplifier may require package, pinout, offset, bandwidth, bias-current, and stability verification; do not assume that a shared TSSOP-14 outline guarantees electrical drop-in compatibility.
Can MCP6044T-E/ST replace MCP6044-E/ST?
MCP6044T-E/ST can be a drop-in replacement only after confirming its temperature grade, qualification classification, electrical limits, and pin mapping against the MCP6044-E/ST requirements. Both parts belong to the same Microchip quad amplifier family and use a 14-lead TSSOP package, which supports a common PCB footprint. Nevertheless, procurement should select the exact ordering code whose operating range and qualification status satisfy the end application.
Is MCP6044-E/ST a drop-in replacement for MCP6044-E/SL?
No, MCP6044-E/ST and MCP6044-E/SL do not share the same PCB footprint. MCP6044-E/ST uses a 14-lead TSSOP package, while MCP6044-E/SL is associated with a 14-lead SOIC package. The devices belong to the same amplifier family, but the body width, lead geometry, and solder pattern differ. A board designed for one package cannot accept the other without layout or adapter changes.
Where can I buy MCP6044-E/ST online?
Use the Request a Quote form on this page to request MCP6044-E/ST pricing, stock confirmation, and current lead time from XAIPART. The manufacturer identifies the MCP6044 family as an active general-purpose amplifier product, and distributor listings include the exact MCP6044-E/ST ordering code. A quote request provides the most current commercial answer because component pricing, allocation, and lead time can change independently of technical documentation.
What is the current price of MCP6044-E/ST?
Request a current MCP6044-E/ST quotation through the Request a Quote form on this page. Component pricing depends on order quantity, market conditions, and current supplier availability, so a static price figure can become inaccurate quickly. The quote form returns the applicable commercial terms for the exact 14-lead TSSOP ordering code rather than for a different package or temperature grade.
What is the lead time and stock status of MCP6044-E/ST?
Request the current MCP6044-E/ST stock position, minimum order quantity, and lead time through the Request a Quote form on this page. Microchip lists the MCP6044 family as a general-purpose product, while distributor inventory for the exact ordering code changes with order activity. A direct quote request provides the most accurate availability information for the quantity, packaging, and ship-to region required by the project.

Dados de referência de engenharia para MCP6044-E/ST — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose MCP6044-E/ST when the design needs four general-purpose amplifiers, single-supply operation down to 1.4 V, rail-to-rail input and output swing, and low 600 nA typical operating current in a 14-lead TSSOP package. It is well matched to slow sensor signals, portable instrumentation, process-control interfaces, and four-channel buffering. Select MCP6044T-E/ST when that specific Microchip ordering code matches the required temperature and qualification framework. Choose MCP6044T-I/ST or MCP6044-I/ST when the industrial-grade classification better matches the ambient requirements. MCP6044T-E/STVAO is relevant when the VAO qualification or marking configuration is required. Confirm the exact pin mapping, electrical limits, and temperature classification before release. Do not substitute a quad amplifier solely because it also uses TSSOP-14; bandwidth, offset, bias current, common-mode range, stability, and channel pin order must all match the circuit requirements.

Comparação com alternativas

Parâmetro Este produto MCP6044T-E/ST MCP6044T-I/ST MCP6044T-E/STVAO MCP6044-I/ST
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 14-lead TSSOP 14-lead TSSOP - same 14-lead TSSOP - same 14-lead TSSOP - same 14-lead TSSOP - same
Number of Amplifiers 4 4 4 4 4
Gain-Bandwidth Product 14 kHz 14 kHz 14 kHz 14 kHz 14 kHz
Typical Operating Current 600 nA 600 nA 600 nA 600 nA 600 nA
Supply Voltage Range 1.4 V to 6 V 1.4 V to 6 V 1.4 V to 6 V 1.4 V to 6 V 1.4 V to 6 V
Input Offset Voltage < 3 mV < 3 mV < 3 mV < 3 mV < 3 mV
Input and Output Capability Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output
Operating Temperature Grade E-grade ordering option T-E ordering option I-grade ordering option VAO ordering option I-grade ordering option

Principais diferenciais

  • Four low-power amplifier channels in one surface-mount package (vs MCP6044T-E/ST)
  • Operation from low-voltage single supplies (vs MCP6044T-I/ST)
  • Low quiescent current for portable designs (vs MCP6044T-E/STVAO)

Notas de projeto

Calculate the amplifier's static supply demand from the 600 nA typical operating-current figure and the selected supply voltage, then add load and sensor currents. Use the manufacturer's maximum quiescent-current and output-current limits for a worst-case battery-life estimate. Because the MCP6044-E/ST supports operation down to 1.4 V, confirm that downstream sensors, ADC inputs, and digital logic remain within valid voltage ranges at the minimum system supply.

Place the supply bypass capacitor directly across the device's supply and ground pins, with a short, low-inductance connection and no excessive series resistance between the capacitor and IC. Route each amplifier input away from switching nodes and high-current return paths. The very low bias current makes PCB contamination and surface leakage potentially significant, so use clean boards, suitable conformal protection where required, and guard techniques for very high-impedance sources.

Do not assume that every quad op amp with a 14-lead TSSOP outline is interchangeable. Verify the channel pin order, supply pins, input and output positions, and maximum input voltage. Also distinguish temperature grades and qualification ordering codes before changing the part number. For the MCP6044 family, the 14 kHz gain-bandwidth product can also be insufficient for fast edges or high-rate signals even when the basic topology appears compatible.

Check settling time against the required gain and sample rate before using the amplifier in a multiplexed measurement path. Higher closed-loop gain reduces usable bandwidth, and capacitive input loading can alter effective bandwidth and stability. For sensor cables, place protection and anti-alias filtering close to the connector. Confirm common-mode range, output swing, and capacitive-load behavior in the manufacturer's electrical-characteristics and application information.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The manufacturer product page confirms the MCP6044 family and available packages but does not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals classifications for this ordering code. Automotive ordering options should not be assumed to apply to MCP6044-E/ST without the corresponding qualification documentation.

Dados verificados em: 2026-11-15 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

mcp6044 datasheet MCP6044-E/ST datasheet pdf MCP6044-E/ST pinout MCP6044-E/ST schematic MCP6044-E/ST equivalent MCP6044-E/ST replacement MCP6044-E/ST cross reference MCP6044-E/ST vs MCP6044T-E/ST MCP6044-E/ST price MCP6044-E/ST stock Microchip MCP6044-E/ST MCP6044 14 kHz quad op amp MCP6044 TSSOP-14 pinout MCP6044 low power sensor application

Componentes & termos relacionados

Microchip Technology MCP6044-E/ST MCP6044T-E/ST MCP6044T-I/ST MCP6044T-E/STVAO MCP6044-I/ST operational amplifier quad operational amplifier analog integrated circuit CMOS rail-to-rail input rail-to-rail output gain-bandwidth product input offset voltage quiescent current bias current 14-lead TSSOP surface mount SMD low-power sensor conditioning industrial process control battery-powered equipment wearable electronics active filtering data-acquisition front end
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ