MKL24Z64VLH4 - 48MHz Cortex-M0+ 64KB Flash USB 2.0 MCU | NXP
MPN: MKL24Z64VLH4 ✓ AktifMKL24Z64VLH4 Ringkasan
A microcontroller (MCU) is a single integrated circuit that bundles a CPU core, program memory, working RAM, and peripherals such as GPIO, timers, and communication controllers on one die. The Kinetis KL2x family hierarchy runs from MCU to 32-bit microcontroller to ultra-low-power Cortex-M0+ device, and the KL2x branch of that family adds a full-speed USB 2.0 On-The-Go (OTG) controller or a crystal-less full-speed USB device controller on top of the Kinetis KL1x feature set, while remaining software compatible with the KL1x, KL3x, and KL4x families and with Kinetis K20 (Cortex-M4) designs for migration.
Key features of this part include 48 MHz Cortex-M0+ execution with a fast interrupt controller, 64 KB of on-chip Flash for firmware, 8 KB of SRAM for buffers and stacks, a 12-bit analog-to-digital converter with 1.71 V to 3.6 V operating span, and on-chip full-speed USB device connectivity that eliminates the need for an external crystal in USB applications. Because the USB controller is crystal-less, the device can enumerate and operate as a USB device directly from an internal trimmed oscillator, reducing bill of materials cost and board area.
Technically, the KL2x architecture balances low active current with fast wake-up behavior, allowing the design to sleep between bursts of USB traffic while the transceiver stays responsive to bus events. The 64-LQFP 10 x 10 mm outline is a deliberately conservative industrial package with long leads, which improves soldering yield and rework convenience compared with fine-pitch packages in volume manufacturing, and the exposed thermal spreader path through the leads keeps junction temperature manageable at 48 MHz.
Typical applications include USB-to-serial and USB-to-Ethernet adapters, low-cost data loggers, HID and dongle peripherals, industrial sensor hubs and battery-powered portable instruments. The 12-bit ADC and multiple timers make it suitable for battery monitor and environmental sensing nodes, while the USB device controller makes it a natural fit for configuration ports on instrumentation.
When designing around this MCU, budget decoupling close to the VDD pins and route the USB D+ and D- differential pair as a short, tightly coupled 90 ohm differential pair on a continuous ground plane. Confirm that your USB host enumerates the crystal-less device at the speed and class you intend, and use the Kinetis KL2x reference designs and SDK examples as the baseline for pin multiplexing and low-power mode entry.
This page consolidates the manufacturer product information with a drop-in alternative matrix, a parameter-by-parameter comparison against other Kinetis KL variants, and practical layout and design notes that go beyond the core datasheet feature list.
Pilihan pengganti yang segera untuk MKL24Z64VLH4 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MKL24Z64VLH4 (sama faktor bentuk dan kaki).
MKL26Z64VLH4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MKL34Z64VLH4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MKL36Z64VLH4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MKL13Z64VLH4
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MKL25Z64VLH4
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →MKL24Z64VLH4 Penilaian maksimum & Ciri-ciri Elektrik
| Device Type | 32-bit ARM Cortex-M0+ Microcontroller (Kinetis KL2) |
| Core | Arm Cortex-M0+ |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory Size | 64 KB (64K x 8) |
| SRAM Size | 8 KB |
| USB Controller | Full-speed USB 2.0 device controller, crystal-less |
| ADC Resolution | 12-bit |
| Tegangan Pemberi Arus Operasi | 1.71 V to 3.6 V |
| Package Type | LQFP-64 (10 x 10 mm) |
| Bilangan Pin | 64 |
| Jenis Pemasangan | Surface Mount |
| Status Lingkungan Hidup | Active |
| Core Processor | Kinetis KL2x ultra-low-power MCU |
| Program Memory Type | Flash |
| Lebar Bus Data | 32-bit |
| Oscillator Type | Internal, crystal-less USB operation |
| Packaging Type | Tray (T) |
Panduan Konfigurasi Pin MKL24Z64VLH4 lqfp-64 (10 x 10 mm)
Konfigurasi pin untuk MKL24Z64VLH4 (lqfp-64 (10 x 10 mm) pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk MKL24Z64VLH4.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
MKL24Z64VLH4 patut untuk 6 aplikasis: USB-to-Serial and USB-to-Ethernet Adapters, Battery-Powered Portable Sensor Node, Industrial CAN Gateway and HMI Controller, USB HID Configuration Port on Test and Measurement Equipment, USB Charging and Power-Path Control, Medical and Diagnostic Peripheral Interface Module.
USB-to-Serial and USB-to-Ethernet Adapters
The MKL24Z64VLH4 suits compact USB adapters because its crystal-less full-speed USB 2.0 device controller removes the need for a 24 MHz crystal and load capacitors, shrinking board area in a dongle-sized enclosure. At 48 MHz Cortex-M0+ with 64 KB Flash and 8 KB SRAM, it has room for a USB stack plus a UART or SPI bridge to an Ethernet controller such as the LAN7500I-ABZJ-TR, or a simple CDC serial profile with no external transceiver. The 64-LQFP (10 x 10 mm) package keeps soldering and rework straightforward in volume production, and the 1.71 V to 3.6 V supply range tolerates both 3.3 V and 2.5 V bus-powered designs. The trade-off is single full-speed operation: for high-speed dual-role host designs, move up to a USB OTG variant.
Disebarkan
Battery-Powered Portable Sensor Node
With a 48 MHz Cortex-M0+ core and an ultra-low-power Kinetis KL2 architecture, the MKL24Z64VLH4 fits coin-cell and Li-ion powered environmental sensing nodes where average current dominates battery life. The 12-bit ADC with a 1.71 V to 3.6 V operating span reads battery voltage directly, while 64 KB of Flash holds a small embedded firmware image and 8 KB of SRAM is enough for a sampling window and a small data buffer. Because USB can be used as a configuration or data-download port rather than a continuous power source, the crystal-less device controller keeps charging dongles simple. Watch the core clock budget: if periodic sampling accuracy must be tight, run the timers from an external crystal and keep USB on the internal reference.
Disebarkan
Industrial CAN Gateway and HMI Controller
The MKL24Z64VLH4 works as the supervisory controller in an industrial CAN gateway or compact HMI because the 64 KB Flash and 8 KB SRAM are adequate for protocol translation while the 48 MHz Cortex-M0+ core gives deterministic response for the CAN message filtering and the serial link. Pair it with a CAN transceiver such as the TJA1057GTK/3Z and an RS-232 or RS-485 front end such as the MAX3221IPWR for legacy equipment. The wide 1.71 V to 3.6 V supply range is useful in 24 V industrial systems where a local regulator cleans up the rail, and the 64-LQFP outline is robust for through-hole-adjacent assembly. Confirm the ambient temperature grade and isolation requirements against the enclosure temperature before volume release.
Disebarkan
USB HID Configuration Port on Test and Measurement Equipment
Instrumentation makers often add a USB HID or CDC configuration port for calibration and firmware updates, and the MKL24Z64VLH4 provides it without a crystal. A 64 KB Flash image can hold a USB HID bootloader plus the instrument control logic, while the 12-bit ADC and multiple timers support front-panel measurement channels. The device runs from 1.71 V to 3.6 V, so it can be powered from the same 3.3 V analog rail region as the rest of the instrument. Because the USB transceiver is crystal-less, temperature drift shows up as small enumeration timing variations, which is acceptable for HID but should be verified if the design relies on USB clock recovery for precision timing. Use the Kinetis SDK HID examples as the starting point for the enumeration descriptors.
Disebarkan
USB Charging and Power-Path Control
In a USB-powered charger or power-path module, the MKL24Z64VLH4 handles enumeration, current-limit negotiation, and status reporting over the full-speed USB device port while supervising the battery and load currents. The 12-bit ADC reads the supply and battery rails inside the 1.71 V to 3.6 V window, and 8 KB of SRAM is sufficient for a small state machine plus logging buffer. The device draws minimal active current when the host stops negotiating, which helps satisfy bus-powered efficiency requirements. Keep in mind the USB device controller here is crystal-less, so any precision current measurement should be referenced to an external reference rather than the internal USB clock source.
Disebarkan
Medical and Diagnostic Peripheral Interface Module
The MKL24Z64VLH4 fits as the interface MCU in a compact diagnostic peripheral, handling a full-speed USB connection to a host PC, a UART link to a sensor front end, and housekeeping GPIO for indicators. The 48 MHz Cortex-M0+ core executes the USB stack alongside acquisition housekeeping, while 64 KB of Flash and 8 KB of SRAM cover a CDC or HID profile with room for a calibration table. The 64-LQFP (10 x 10 mm) package and the single 1.71 V to 3.6 V rail simplify certification-focused board layouts where a smaller fine-pitch package would complicate inspection. For designs requiring a reinforced isolation barrier to the host, add a dedicated isolator and keep the USB lines on the protected side of it.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MKL24Z64VLH4 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MKL26Z64VLH4 | MKL34Z64VLH4 | MKL36Z64VLH4 | MKL13Z64VLH4 | MKL25Z64VLH4 |
|---|---|---|---|---|---|---|
| Package | LQFP-64 (10 x 10 mm) | LQFP-64 (10 x 10 mm) - same | LQFP-64 (10 x 10 mm) - same | LQFP-64 (10 x 10 mm) - same | LQFP-64 (10 x 10 mm) - same | LQFP-64 (10 x 10 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ |
| Maximum CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 72 MHz | 48 MHz | 48 MHz |
| Flash Memory | 64 KB (64K x 8) | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| SRAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| USB Support | Crystal-less full-speed USB 2.0 device controller | USB device controller | USB 2.0 OTG host/device | USB 2.0 OTG host/device | No USB controller | No USB controller |
| ADC Resolution | 12-bit | 12-bit | 12-bit | 12-bit | 12-bit | 12-bit |
| Operating Supply Voltage | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V |
| GPIO / Peripheral Count | Kinetis KL2 baseline | Higher GPIO and peripheral count | Higher GPIO with OTG host capability | Higher GPIO with faster core | Fewer USB-specific peripherals | Fewer GPIO than KL24 |
Penyeberangsung Jelas
- Crystal-less full-speed USB 2.0 device controller reduces external component count (vsMKL13Z64VLH4)
- Broad supply range allows one MCU across portable and industrial rails (vsMKL25Z64VLH4)
- Direct USB OTG upgrade path without a PCB change (vsMKL34Z64VLH4)
- Core headroom for compute-heavy firmware (vsMKL36Z64VLH4)
Catatan Desain
Keep the USB D+ and D- pair as a short, length-matched differential pair with 90 ohm differential impedance over a continuous ground plane, and keep the pair clear of switching nodes, antenna-like copper, and the crystal-less internal oscillator keep-out region. Place the bulk supply capacitor and a 100 nF high-frequency capacitor on the VDD pins of the 64-LQFP (10 x 10 mm) package as close as physically possible, and provide a short ground return for each decoupling capacitor. Verify the USB trace impedance against the actual stack-up rather than relying on nominal width values.
Decide early whether USB is a power source or a data path. If the MKL24Z64VLH4 is bus-powered, budget the total system current against the USB enumeration budget and keep the crystal-less USB controller enabled only while the host is connected, since a permanently active USB PHY consumes current in battery designs. If the device is self-powered, use a dedicated current-sense path such as an INA240A1PW output into the 12-bit ADC so port current can be limited and reported rather than inferred.
The most common mistakes with this part are firmware-level rather than electrical: assuming a 24 MHz crystal footprint is needed, and assuming the USB peripheral in the KL2x behaves exactly like the OTG variant. Because the MKL24Z64VLH4 uses a crystal-less full-speed USB device controller, host-side enumeration descriptors and bus timing must be validated on real hardware, and any design needing USB host or OTG role must move to the KL34 or KL36 variant. Always confirm the pin multiplexing table for the exact 64-LQFP variant before committing the layout.
Estimated: with a 48 MHz Cortex-M0+ core, a 3.3 V supply, and a 15 mA active current draw, the internal dissipation is roughly 3.3 V x 0.015 A = 0.05 W, which is negligible for the 64-LQFP (10 x 10 mm) outline and needs no dedicated heat sinking. Real thermal risk appears only if the surrounding board runs hot or if the part is used at elevated ambient temperature; keep the exposed ground pad area of the LQFP free of thermal isolation and maintain copper for heat spreading on the board.
Flash and SRAM budgeting mistakes surface late in firmware development. A 64 KB image must hold the bootloader, the USB stack, and application logic simultaneously, so plan for a linker script that reserves the bootloader region and use the Kinetis SDK flash programming utilities for field updates over USB. With only 8 KB of SRAM, large USB receive buffers or display framebuffers will not fit; use DMA-capable peripherals or external memory instead of inflating the RAM footprint.
Maklumat Kesediaan
The manufacturer lists the MKL24Z64VLH4 as an active part with an environmental quality section and shipping information on the NXP product page; specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not reproduced in the product listings, so they are recorded as unknown. This is a general-purpose Kinetis KL2 part and is not marketed as an AEC-Q100 automotive-qualified device.