Texas Instruments

OPA202ID - 36V Low-Noise Precision Op Amp | Texas Instruments

MPN: OPA202ID ✓ Aktif
36 V Vdss 8-SOIC, 0.154 inch width, 3.90 mm width Package
MOQ: 1 |

OPA202ID Ringkasan

The Texas Instruments OPA202ID is a single-circuit, low-noise precision operational amplifier featuring a super-beta bipolar-junction-transistor input stage, 36 V maximum supply capability, and an 8-pin SOIC package. Its specified input noise is 0.2 uVPP and 9 nV/sqrt(Hz), while its heavy-capacitive-drive capability reaches 25 nF. These characteristics place it in the operational-amplifier hierarchy: precision amplifier, analog signal-conditioning IC, signal-chain component.

A precision operational amplifier is a voltage-feedback amplifier designed to amplify the voltage difference between its inverting and non-inverting inputs while minimizing offset, noise, bias-current, and distortion effects. The OPA202ID uses a super-beta BJT input architecture to balance low input noise with low bias current. Its low output impedance and capacitive-load drive capability make it useful when the amplifier must directly interface with cables, sensors, converters, and other real-world analog nodes.

The primary distinguishing specifications are 0.2 uVPP input noise, 9 nV/sqrt(Hz) noise density, 25 nF capacitive-load drive, and a 36 V operating supply. The OPA202ID is supplied in an 8-SOIC package with a push-pull output stage. Its single-circuit configuration allows it to perform precision current-voltage conversion, differential sensing, gain amplification, active filtering, and signal buffering without requiring a dual or quad device.

The super-beta input stage is the key architectural feature. Compared with a conventional bipolar precision amplifier, it is designed to reduce input bias current while retaining low voltage noise. Low bias current is especially valuable when the source impedance is high, because current through the source can create input-referred offset and gain errors. The combination of low bias current, low output impedance, and 25 nF capacitive-drive capability also helps preserve signal integrity when driving acquisition-system inputs rather than operating only with low-impedance laboratory loads.

Typical uses include precision current sensing, low-level sensor amplification, analog-to-digital converter input conditioning, active transducers, and instrumentation buffers. The part can also serve in audio and communication interfaces where low noise matters and the connected load includes significant cable or probe capacitance. Industrial measurement systems benefit from its low bias current, while higher-voltage signal chains can operate from a ±18 V split supply or another compatible arrangement within the 36 V total rating.

When designing around the OPA202ID, check the exact pin assignment in the manufacturer pin-description table before routing the PCB. Place input and feedback components close to the amplifier, keep sensitive input traces away from switching nodes, and treat the specified 25 nF drive capability as a design boundary rather than an unlimited load rating. Confirm output-current limits, common-mode range, supply current, and stability requirements for the selected operating point.

This product record combines the manufacturer product-page description, exact ordering information, package details, operating characteristics, and application-oriented engineering guidance. It also distinguishes the OPA202ID from other OPA202-family orderable variants, clarifies where drop-in alternatives are limited, and identifies engineering checks for noise, bias current, capacitive loading, and PCB implementation.

Pilihan pengganti yang segera untuk OPA202ID — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

OPA202UID

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 8-SOIC (D package)
Same OPA202 family and 8-SOIC D-package family configuration; ordering-specific temperature-grade or option details must be confirmed, with no published numerical deviation identified

📋 Alternatif rujukan (tidak dalam katalog)

OPA202ID Penilaian maksimum & Ciri-ciri Elektrik

Product Type Single-circuit precision operational amplifier
Manufacturer Texas Instruments
Maximum Supply Voltage 36 V
Input Noise Peak-to-Peak 0.2 uVPP
Input Noise Density 9 nV/sqrt(Hz)
Heavy Capacitive Drive 25 nF
Input Stage Architecture Super-beta bipolar-junction-transistor input stage
Power Class Low-power operational amplifier
Jenis Output Push-pull output
Number of Circuits 1 circuit
Number of Terminals 8 terminals
Kemasan 8-SOIC, 0.154 inch width, 3.90 mm width
Package Code D
Package Shape Rectangular
Terminal Form Gull wing
Jenis Pemasangan Surface mount
Temperature Grade Industrial

Panduan Konfigurasi Pin OPA202ID rectangular

Konfigurasi pin untuk OPA202ID (rectangular pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai rectangular untuk OPA202ID

Tiada data garisan pin yang diperoleh untuk OPA202ID.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

OPA202ID patut untuk 6 aplikasis: Precision Current-Sensing Signal Chains, High-Impedance Sensor Interfacing, Fast-Conversion ADC Input Conditioning, Industrial Instrumentation and Buffering, Low-Noise Audio and Communication Interfaces, Active Filters and Precision Signal Conditioning.

⚡

Precision Current-Sensing Signal Chains

The OPA202ID fits precision current-sense amplifiers because its super-beta BJT input stage combines low input noise with low bias current, while the push-pull output supports accurate signal amplification. A shunt sensor produces a small differential voltage that the amplifier can convert into a voltage proportional to current. Low bias current limits error when the shunt and input network have appreciable source resistance, and the specified 0.2 uVPP input noise helps preserve small full-scale signals. The 36 V maximum supply rating also provides flexibility in industrial measurement systems. Before finalizing the circuit, confirm the common-mode input range, output swing, gain error, and operating current for the selected shunt and supply configuration.

🧩

High-Impedance Sensor Interfacing

OPA202ID is appropriate for high-impedance sensor interfaces because its super-beta bipolar input architecture is designed to combine low input bias current with low voltage noise. These characteristics reduce errors when a sensor has a high source impedance or when the input network must not disturb a small sensing current. The device can be configured as a non-inverting or inverting amplifier around the precision signal while its 0.2 uVPP input noise limits added signal uncertainty. The 25 nF capacitive-drive specification also helps when the sensor is connected through a cable or probe. Check the exact input bias current, offset behavior, common-mode limits, and noise spectrum against the sensor impedance before setting the closed-loop gain.

🖥️

Fast-Conversion ADC Input Conditioning

The OPA202ID can condition inputs for precision, fast-acquisition analog-to-digital converters where low noise and stable drive into sampling capacitance matter. Its 0.2 uVPP input noise and 9 nV/sqrt(Hz) noise density reduce amplifier-added uncertainty, while the specified 25 nF capacitive-load drive capability supports interfaces that include converter input capacitance, protection devices, or routing capacitance. Low output impedance is particularly useful when the converter performs periodic charge sampling during conversion. The amplifier should be placed close to the converter, with feedback components positioned to minimize parasitic capacitance. Verify the selected ADC's input range, kickback behavior, acquisition time, and settling requirements rather than relying only on nominal bandwidth figures.

🏭

Industrial Instrumentation and Buffering

OPA202ID suits industrial instrumentation that buffers weak sensor signals before digitization or control. The super-beta BJT input stage provides low bias current, which helps preserve the integrity of high-resistance transducers and long analog connections. Its 0.2 uVPP input noise and 9 nV/sqrt(Hz) noise density are valuable when the process variable is represented by a small voltage. The single push-pull output in an 8-SOIC package provides a practical implementation for non-inverting, inverting, differential, or active-filter stages. For field-based equipment, keep sensitive traces away from power converters and relay nodes, use stable reference components around the amplifier, and confirm industrial temperature and transient requirements against the exact orderable device.

🎧

Low-Noise Audio and Communication Interfaces

OPA202ID can be used in low-level audio and communication interfaces where signal amplitude is small and added noise is directly audible or measurable. Its specified 0.2 uVPP input noise and 9 nV/sqrt(Hz) noise density provide a low-noise starting point for microphone preamplifiers, line-level buffers, and communication-signal conditioning stages. The heavy-capacitive-drive capability up to 25 nF is useful when the amplifier precedes a connector, cable, or codec input that presents appreciable capacitance. In a practical design, use short low-noise input paths, maintain clean return connections, and ensure that the output can remain linear over the required signal swing and bandwidth. Confirm distortion, slew-rate, output-current, and common-mode requirements for the actual channel.

🌐

Active Filters and Precision Signal Conditioning

OPA202ID is suitable for active filters and precision conditioning networks that require low input bias current, low noise, and predictable behavior around the signal source. The super-beta BJT input architecture reduces bias-current error in equal-input-resistance topologies, while the 0.2 uVPP noise specification helps maintain a clean measurement floor. Its push-pull output provides bidirectional drive for filter networks and downstream instrumentation. Component tolerances and temperature drift should be reviewed alongside the amplifier because passive-network error can dominate the final filter accuracy. Keep resistor networks compact and symmetric where applicable, place feedback components close to the device, and validate phase margin and gain against the intended frequency range. The exact gain-bandwidth and unity-gain stability values should be confirmed in the manufacturer datasheet.

Ringkasan Produk Disebarkan

OPA202ID Texas Instruments Dipergunakan di: Precision Current-Sensing Signal Chains, High-Impedance Sensor Interfacing, Fast-Conversion ADC Input Conditioning, Industrial Instrumentation and Buffering, Low-Noise Audio and Communication Interfaces, Active Filters and Precision Signal Conditioning OPA202UID Same-family OPA202 amplifier option for design review Dipergunakan di: Precision Current-Sensing Signal Chains, High-Impedance Sensor Interfacing, Fast-Conversion ADC Input Conditioning, Industrial Instrumentation and Buffering, Low-Noise Audio and Communication Interfaces, Active Filters and Precision Signal Conditioning
What is the OPA202ID?
The OPA202ID is a single-circuit, low-noise precision operational amplifier from Texas Instruments. It uses a super-beta BJT input stage, operates with up to 36 V, provides 0.2 uVPP input noise and 9 nV/sqrt(Hz) noise density, and is packaged in an 8-SOIC. According to the Texas Instruments product page, its low output impedance and heavy-capacitive-drive capability are intended for modern, fast-acquisition precision analog interfaces.
What are the key specifications of OPA202ID that engineers should know?
The OPA202ID combines a 36 V maximum supply rating with 0.2 uVPP input noise, 9 nV/sqrt(Hz) noise density, and 25 nF capacitive-load drive capability. Texas Instruments describes it as a low-power, super-beta, precision operational amplifier with one push-pull output circuit in an 8-SOIC package. These characteristics make it relevant to high-impedance sensors, precision converter interfaces, instrumentation, and other low-noise analog signal chains.
What noise performance does OPA202ID provide?
The OPA202ID provides input noise of 0.2 uVPP and a noise density of 9 nV/sqrt(Hz). According to the Texas Instruments OPA202 product description, it is designed for precision, low-noise signal acquisition. These figures make the amplifier particularly useful when the signal source has a small output amplitude and the downstream converter or measurement system has limited input-referred noise.
Can OPA202ID drive a large capacitive load?
Yes. The OPA202ID is specified for heavy capacitive-load drive up to 25 nF. According to the Texas Instruments product-page description, its low output impedance supports interface requirements involving modern, fast-acquisition precision ADCs and other capacitive loads. The exact stability, output-current, and frequency behavior at a particular load should still be checked against the manufacturer operating conditions before finalizing the design.
Where can I download the OPA202ID datasheet PDF?
The official OPA202 family datasheet is available from Texas Instruments at https://www.ti.com/lit/gpn/OPA202, and the product page is https://www.ti.com/product/OPA202. These documents contain the ordering information, electrical characteristics, pin descriptions, and application details needed to evaluate OPA202ID. Use the manufacturer PDF for PCB pin assignment and design sign-off.
Where can I find the OPA202ID pinout?
The OPA202ID pin assignment is identified in the official Texas Instruments OPA202 family datasheet at https://www.ti.com/lit/gpn/OPA202. Because OPA202ID uses the 8-SOIC package, the PCB footprint must follow the manufacturer pin-description table for the D package. Confirm pin numbers directly against that table before assigning power, inputs, output, and any offset-null or exposed functions.
OPA202ID vs OPA202UID - which is the better choice?
OPA202ID is the industrial-temperature OPA202 option in the D-package 8-SOIC ordering family, while OPA202UID is another orderable member of the same OPA202 family. The available OPA202 family description confirms that both belong to the low-power, super-beta, low-noise precision amplifier family, but exact ordering details should be checked on the Texas Instruments product page. Choose the variant whose package, grade, lifecycle, and electrical options match the production requirement.
When should I choose OPA202ID instead of a general-purpose op amp?
Choose OPA202ID when the design needs very low input noise, low bias current, 36 V supply capability, and reliable drive into a substantial capacitive load. Its super-beta BJT input stage is suited to high-impedance sources and precision measurements, whereas a general-purpose amplifier may have higher noise or weaker capacitive-load behavior. It is less attractive when the smallest possible package, lowest cost, or highest unity-gain bandwidth is the overriding requirement.
Is OPA202ID suitable for high-impedance sensor amplification?
Yes, OPA202ID is well suited to high-impedance sensor amplification because its super-beta BJT input stage is designed for low bias current while retaining low input noise. The device can preserve small signals from sources where bias-current error would otherwise become significant. Actual sensor compatibility still depends on source resistance, frequency, input bias-current error, noise, and the common-mode range at the operating point.
What can replace OPA202ID?
A true drop-in replacement should use the same 8-SOIC footprint, pin arrangement, supply range, input-stage behavior, output drive, and key electrical ratings. The verified cross-reference results identify the OPA202 family and the OPA202ID ordering option but do not establish five distinct pin-compatible replacements. OPA202UID is the closest same-family candidate identified, while OPA202IPD uses a different package and therefore is not a drop-in substitute for this assembly.
What is the best equivalent for OPA202ID?
OPA202UID is the closest same-family candidate identified for OPA202ID because it is an orderable member of the Texas Instruments OPA202 precision amplifier family and is associated with the same family-level functional characteristics. Confirm its exact D-package ordering suffix, pinout, temperature grade, and electrical limits on the manufacturer product page before treating it as a drop-in replacement. No cross-brand equivalent can be recommended solely from the available cross-reference results.
Where to buy OPA202ID online?
Use the Request a Quote form on this page to request OPA202ID pricing, stock confirmation, and delivery information. The part is an 8-SOIC single-circuit operational amplifier from Texas Instruments, and the manufacturer product page remains the authoritative source for ordering options. A formal quotation is required because current availability and commercial terms can change without changing the component specifications.
What is the price of OPA202ID?
The current commercial price for OPA202ID should be obtained through the Request a Quote form on this page. Pricing depends on order quantity, package suffix, delivery destination, and current channel conditions. The structured pricing area reflects qualifying quantity-break data, while the Request a Quote workflow provides a current response for production purchasing.
What is the lead time for OPA202ID?
Request the current lead time and minimum order quantity through the Request a Quote form on this page. The OPA202ID is identified as an active Texas Instruments ordering option in an 8-SOIC package, but manufacturing and distribution schedules can vary by quantity and date. Confirm the committed delivery date as part of the quotation rather than relying on a historical inventory snapshot.
Is OPA202ID in stock?
Current OPA202ID inventory should be confirmed through the Request a Quote form on this page. Distributor listings indicate market availability for the exact 8-SOIC ordering option, but stock quantities and fulfillment dates are time-sensitive and should not be treated as guaranteed inventory. Include your required quantity, target date, and ship-to location in the quote request.
How should OPA202ID be laid out for low noise and capacitive loading?
Place the amplifier's input, feedback, and compensation components close to the device and keep input traces short and away from switching nodes or high-current paths. Route the output to the capacitive load with a short, controlled trace and confirm the load network against the manufacturer's stability guidance. For sensitive measurements, use a quiet ground reference and avoid long parallel runs beneath or beside the input nodes.

Data referensi kejuruteraan untuk OPA202ID — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose OPA202ID when a design needs very low input noise, low bias current, low output impedance, and reliable drive into a capacitive load. Its 0.2 uVPP input noise, 9 nV/sqrt(Hz) noise density, super-beta BJT input stage, and 25 nF capacitive-drive capability make it particularly appropriate for precision current sensing, high-impedance sensors, ADC input conditioning, and instrumentation buffering. OPA202UID is the closest identified same-family alternative for an 8-SOIC configuration, so compare ordering-specific temperature grade and lifecycle details before changing parts. OPA202IPD should not be treated as a drop-in alternative for an OPA202ID assembly because its P-package construction differs. If the application does not require the OPA202 noise, bias-current, and capacitive-drive characteristics, a lower-cost general-purpose amplifier may be sufficient, provided its input offset, bandwidth, output drive, and stability are acceptable.

Perbandingan dengan Gantian

Parametr Produk Ini OPA202UID
Brand Texas Instruments Texas Instruments
Package 8-SOIC (D package) 8-SOIC (D package)
Circuit Count 1 circuit 1 circuit
Maximum Supply Voltage 36 V 36 V
Input Noise Peak-to-Peak 0.2 uVPP 0.2 uVPP
Input Noise Density 9 nV/sqrt(Hz) 9 nV/sqrt(Hz)
Capacitive-Load Drive 25 nF 25 nF
Input Stage Super-beta BJT Super-beta BJT
Output Type Push-pull Push-pull
Power Class Low power Low power

Penyeberangsung Jelas

  • Lower-noise input stage for precision acquisition (vsOPA202UID)
  • High capacitive-load drive for real-world analog interfaces (vsOPA202UID)
  • Wide supply capability for precision signal chains (vsOPA202UID)

Catatan Desain

Place input, feedback, and compensation components directly beside OPA202ID pins, and keep the sensitive input path short. High-impedance nodes are susceptible to leakage, surface contamination, and stray capacitance, so avoid routing them beside switching-power nodes, relay contacts, or long ground-return paths. For a capacitive load, use the shortest practical output trace and confirm that the selected feedback network remains stable at the maximum connected capacitance.

The specified 25 nF capacitive-drive capability is useful for probe, cable, and converter-input loading, but the amplifier still requires adequate loop stability and output-current margin. Establish the intended load, output voltage, frequency, and supply configuration, then compare them with the manufacturer characteristics. Add an isolation resistor only after checking that the resulting load and feedback network preserve the required settling behavior and do not create unacceptable gain error.

Do not treat the 36 V maximum supply rating as the recommended operating point, and do not assume that the 25 nF capacitive-load figure applies at every frequency or output amplitude. Use the pin-description table in the manufacturer datasheet to confirm the D-package pinout. Also account for input offset, bias-current error, noise gain, common-mode range, output swing, and supply-current limits when defining the usable precision of the circuit.

Separate the sensitive analog path from digital and switching signals, and provide a low-impedance return beneath or adjacent to the circuit where the board stackup permits it. For gain stages with high closed-loop gain, use closely placed feedback resistors to minimize parasitic feedback. Place bypass capacitors close to the supply pins and follow the exact compensation and decoupling arrangement shown for the chosen OPA202 configuration in the manufacturer documentation.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The OPA202 family is an industrial precision operational amplifier and is not an automotive-qualified product. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product documentation for the exact orderable device.

Pencarian Berhubungan

OPA202ID datasheet OPA202ID pinout OPA202ID datasheet pdf OPA202ID equivalent OPA202ID replacement OPA202ID cross reference OPA202ID vs OPA202UID OPA202ID footprint OPA202ID 36V op amp OPA202ID 25nF capacitive load OPA202ID noise density Texas Instruments OPA202ID OPA202ID price OPA202ID stock OPA202ID application circuit

Komponen dan Tanda berkaitan

Texas Instruments OPA202ID OPA202UID OPA202IPD OPA202 operational amplifier precision operational amplifier analog signal-conditioning IC super-beta BJT bipolar-junction transistor input bias current input noise noise density 0.2 uVPP 9 nV/sqrt(Hz) 25 nF capacitive load 36 V supply push-pull output 8-SOIC SOIC package family surface-mount package precision current sensing high-impedance sensor interface ADC input conditioning industrial instrumentation active filter
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ